Page 1: Introduction
SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors ....20 To Lock The Doors .....21 Using The Panic Alarm .
Page 11 Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbags ...44 Passenger Airbag On/Off Switch – If Equipped ......54 Event Data Recorder (EDR) .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Transmission—If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle.
Page 15: Steering Wheel Lock - If Equipped
STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid key to start the engine. NOTE: A key that has not been programmed is consid- ered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle.
Page 17: Customer Key Programming
NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 19: Illuminated Entry
The security system will also disarm, if the vehicle is started with a programmed Sentry Key. If an unpro- grammed Sentry Key is used to start a vehicle, the engine will start and run for 2 seconds and then shut down. After six unsuccessful attempts at starting the engine, the system will shut down until the correct key is used.
Page 20: Remote Keyless Entry
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY Remote Keyless Entry Transmitter This system allows you to lock or unlock the doors or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
Page 21: To Lock The Doors
3. Release both buttons at the same time. 4. Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the transmitter. NOTE: Pressing the LOCK button on the transmitter while you are inside the vehicle will activate the Security Alarm.
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the transmitter, while you are inside the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
Page 23: General Information
To cancel the Panic mode press and release the PANIC button on the transmitter a second time. Panic mode will automatically cancel after 3 minutes or if the vehicle is started or exceeds 15 mph (24 km/h). During the Panic Mode, the door locks and remote keyless entry systems will function normally.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When entering program mode using that fob, all other programmed transmitters will be erased and you will have to reprogram them for your vehicle. Use the following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key: 1.
Page 25: Battery Replacement
NOTE: If you do not have a programmed transmitter, contact your dealer for details. Battery Replacement The recommended replacement battery (2 required) is CR2032. 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart.
Page 26: Remote Starting System - If Equipped
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED Your vehicle may be equipped with a remote starting system, which will allow the vehicle to be started from distances up to approximately 300 feet away from the vehicle using the remote keyless entry key fob which is part of your ignition key.
Page 27: Door Locks
unlocked, you have 60 seconds to enter the vehicle, insert the key in the Ignition and move it to the RUN position, otherwise the engine will cancel remote start and auto- matically turn off. Remote start will also cancel if any of the following occur: •...
Page 28: Power Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
Page 29 locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature This feature unlocks all the doors of the vehicle when any door is opened. The following must be met: • The doors of the vehicle must be locked automatically by the Automatic Door Lock feature.
Page 31: Child Protection Door Lock
Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. Child Lock Lever THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 To use the system, open each rear door, slide the lever UP to engage the locks and DOWN to disengage the child- protection locks.
Page 32: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle. WINDOWS Power Windows Power Window Switch The control on the left front door has up-down switches that give you finger tip control of all four power win-...
Page 33: Auto Down (Driver's Side Only)
Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the Auto Down movement, operate the switch in either the up or down direction and release the switch.
Page 34: Occupant Restraints
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE with the rear windows open, open the front and rear windows together to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, knee bolsters, front airbags for both the driver and front passenger, and if equipped left and right side curtain...
Page 35: Lap/Shoulder Belts
of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the front center seating position (with full bench seat) have combination lap/ shoulder belts.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 37 plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! •...
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 39: Adjustable Upper Shoulder Belt Anchorage
6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 40: Automatic Locking Mode - If Equipped
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in the desired position.
Page 41: Seat Belt Pretensioners
loose end of the webbing. Wear the lap belt snug against the hips. Sit back and erect in the seat, then adjust the belt as tightly as is comfortable. Seat Belt Pretensioners The seat belts for front outboard seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON...
Page 43: Seat Belts And Pregnant Women
Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen.
Page 44: Driver And Right Front Passenger Supplemental Restraint System (Srs) - Airbags
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
Page 45 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
Page 47 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners • Passenger Airbag Disable (PAD) Indicator Light (Ex- tended Cab Vehicles Only) • Passenger Side frontal Airbag ON/OFF Switch (Ex- tended Cab Vehicles Only). How the Airbag System Works •...
Page 49 WARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE symbol and the word OFF to show that the passenger airbag will not inflate during a collision requiring air- bags. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
Page 51 belted properly and do not position items in the area where the window bag inflates. This especially applies to children. The window bag is only about 3-1/2 inches (9 cm) thick when it is inflated. • The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position every- one for the best interaction with the front airbag.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: •...
Page 53 WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, and both front seat belt retractor assemblies (w/ pretensioners), replaced by an authorized dealer as soon as possible. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Maintaining Your Airbag System WARNING! •...
Page 54: Passenger Airbag On/Off Switch - If Equipped
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 5 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
Page 55 • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, •...
Page 56: Event Data Recorder (Edr)
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the key from the switch. This will shut off the passenger frontal airbag. The passenger frontal airbag symbol and the word “OFF” on the passenger airbag disable (PAD) lamp will illuminate when the ignition switch is turned to the ON position.
Page 57 pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US govern- ment and various states.
Page 58: Child Restraint
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems.
Page 59 • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag that does not have a switch to turn the airbag Off. An airbag deployment could cause severe injury or death to infants in this position.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm. For additional information, refer to www.seatcheck.org.
Page 61 use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Club Cab • The Club Cab front and rear right (if equipped with a rear seat) passenger seating positions have lower anchorages for LATCH equipped child restraints. Quad Cab • The Quad Cab second row seat has lower anchorages that capable accommodating...
Page 63 Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE over the top of the anchorage bars, pushing aside the seat cover material. Then attach the tether strap to the anchor- age located on the back of the seat, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint.
Page 65 Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with either cinch- ing latch plates or automatic locking retractors, which are designed to keep the lap portion tight around the child restraint so that it should not be necessary to use a locking clip.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Tether Anchor The Club Cab model has two routing straps located behind each of the rear outboard seat- ing positions. The tether anchor itself is located in the center of vehicle, in between the two seating positions.
Page 67 Tether Strap at the Front Passenger Seat (Club Cab) 1. Route the child restraint tether strap up and over the front passenger seat back and under the head restraint. 2. Connect the tether strap to the lower anchor. 3. Remove the slack in the tether strap so that it is pulled tight.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Route the tether strap across to the center tether anchorage. The center tether is located behind the slide door in the center of the vehicle, between the two seating positions. 3. Remove the slack in the tether strap so that the anchor strap is pulled tight.
Page 69 Tether Straps at the Rear Passenger Seat (Quad Cab) 1. Route the child restraint tether strap under the head restraint for the outboard seating positions, and then through the anchor strap outer loop (webbing material loop), located directly behind the child restraint. 2.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Double Cab...
Page 71: Engine Break-In Recommendations
WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 72: Safety Tips
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an ex-...
Page 73: Safety Checks You Should Make Inside The Vehicle
Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation. Check for proper air flow through all defroster ducts. If there are any question regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer Seat Belts Inspect the belt system periodically, checking for cuts,...
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks.
Page 75 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......79 Inside Day/Night Mirror ....79 Automatic Dimming Mirror —...
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Open And Close The Hood ....88 Lights ....... .90 Interior Lights .
Page 77 Reset Button ......104 Global Reset ......105 Step Button .
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Floor Console — If Equipped ....121 Floor Console Features ....121 Center Storage Compartment —...
Page 79: Mirrors
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck).
Page 80: Outside Mirrors
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight...
Page 81: Electric Remote-Control Mirrors
Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move.
Page 82: Heated Mirrors - If Equipped
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object.
Page 83: Front Seats Manual Seat Recliners
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 84: Manual Lumbar Support Adjustment - If Equipped
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
Page 85: Adjustable Head Restraints - Front Seating Positions
Adjustable Head Restraints — Front Seating Positions Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the driver’s seat cushion. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
Page 87: Club Cab/Quad Cab Rear Seat
control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Tilt Adjustment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Club Cab/Quad Cab Rear Seat More cargo space is available by lifting up on the rear seat cushion.
Page 88: To Open And Close The Hood
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE heat level. Flashing indicator lights on the switch indicate that the Heated Seat system needs servicing. WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 89 Then push the safety latch lever down while lifting the grille with your right hand. It is located at the top center of the grille just left of center. Lift the hood and gas filled props will hold it open. Secondary Latch Location (Push Down) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 To prevent possible damage, do not slam the hood to...
Page 90: Lights
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.When a door is open and the interior lights are on, rotating the dimmer...
Page 91: Battery Saver
control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the Party mode because it allows the doors to stay open for extended periods of time without discharging the vehi- cle’s battery.
Page 92: Headlamp Delay
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp Delay To aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 60 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off.
Page 93: Daytime Running Lights (Canada Only)
To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
Page 94: Cargo Light - If Equipped
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO Light — If Equipped The cargo lights are turned on by pressing on the CARGO button. The interior lights will also turn on when the cargo lights are on. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
Page 95 The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective.
Page 96: Windshield Wipers And Washers
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or LOW beam. WINDSHIELD WIPERS AND WASHERS The multifunction control lever is located on the left side of the steering column.
Page 97: Windshield Washers
Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position.
Page 98: Tilt Steering Column
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE after the washer knob is released. It will then resume the intermittent interval previously selected. If the washer knob is pushed, for a period greater than 1 second, while in the OFF position, the wiper will wipe approximately three wipes, after the wash knob is released.
Page 99: Electronic Speed Control - If Equipped
WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL —...
Page 100: To Set At A Desired Speed
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate speed control with- out erasing the memory.
Page 101 Tapping the DECEL button once will result in a speed decrease (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed will decrease. For example, tapping the button 3 times will decrease the speed by 3 times the speed listed in the table below (refer to the table below for the speed for your specific engine).
Page 102: To Accelerate For Passing
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
Page 103: Overhead Console
OVERHEAD CONSOLE The overhead console has the following features: • Courtesy Lights • Garage Door Opener — If Equipped • Compass/Temperature Mini-Trip Computer — If Equipped UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights.
Page 104: Compass/Temperature Mini-Trip Computer
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE COMPASS/TEMPERATURE MINI-TRIP COMPUTER This feature allows you to choose between a compass/ temperature display and one of four trip conditions being monitored. US/M Button Use this button to change the display from U.S. to metric measurement units.
Page 105: Global Reset
Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and elapsed time displays.
Page 106: Average Fuel Economy (Avg Eco)
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is...
Page 107: C/T Button
C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges.
Page 108: Manual Compass Calibration
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After completing one 360° turn, with the vehicle traveling less than 5 mph (8 km/h), in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally.
Page 109: Outside Temperature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 110: Garage Door Opener - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Page 111 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 112: Programming Homelink
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 113 NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the Gate Operator/Canadian Pro- gramming section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter.
Page 114: Canadian Programming/Gate Programming
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device.
Page 115: Erasing Homelink Buttons
etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-355- 3515. Erasing HomeLink Buttons To erase programming from the three buttons (individual buttons cannot be erased but can be reprogrammed - note below), follow the step noted: •...
Page 116: Power Sunroof - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE vehicle entry. HomeLink operation will be re-stored when the Security Alarm has been Disarmed . If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously trained frequencies, hold down both outside buttons until the green light begins to flash.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Sunroof Switch (No Console) Sunroof Switch Console Press and hold the “V” button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward.
Page 118: Express Open Feature
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again. Express Open Feature During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position.
Page 119: Sunroof Maintenance
WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, sunroof,other controls, or move the vehicle.
Page 120: Electrical Outlet Use With Engine Off (Battery Fed Configuration)
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: All accessories connected to these outlets should be removed or turned OFF when the vehicle is not in use to protect the battery against discharge (unless the cus- tomer has reconfigured the fuse block to switched battery feed).
Page 121: Understanding The Features Of Your Vehicle 121
FLOOR CONSOLE — IF EQUIPPED Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat has the following features: • Miscellaneous storage compartments • Flexible cup holder inserts • Portable phone storage bin • Portable phone cord routing between lid and base on forward edge •...
Page 122: Center Storage Compartment - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outlet and Portable Phone Storage The console is equipped with a power outlet, portable phone storage bin, and phone cord routing. The phone storage bin can be used when easy access to the phone is needed.
Page 123: Cup Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 CUP HOLDERS If your vehicle has bucket seats with a center console, there are three cup holders located on the console. Refer to the section on floor console. A two-cavity cup holder is available on all Quad Cab with rear seats mounted on the floor.
Page 124: Rear Window Features
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster – If Equipped CAUTION! Use care when washing the inside of the rear win- dow to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
Page 125: Sliding Rear Window - If Equipped
Sliding Rear Window – If Equipped Sliding Rear Window Latch A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 TAILGATE Tailgate Removal To simplify mounting a camper unit with an overhang,...
Page 126: Two Position Tailgate / Upper Load Platform
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Lift the tailgate off of the pivot on the passenger side by pulling upward and rearward at the same time. 4. Slide the tailgate to the passenger side while making sure clearance from the box and taillight is maintained. To reinstall the tailgate, do the following: 1.
Page 127 1 — Bulkhead Divider 2 — Upper Load Floor Indent 2. Secure the tailgate in the partially open position: • Open the tailgate slightly. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 • Snap the tailgate support cable between the cable guide and the tailgate bumper.
Page 128: Slide-In Campers
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Remove both cables from between the cable guides and the tailgate bumpers and lower the tailgate. CAUTION! • Care should always be exercised when operating a vehicle with cargo. Vehicle speeds may need to be reduced.
Page 129: Carbon Monoxide Warning Vehicles Equipped With A Cap Or Slide-In Campers
To mount a camper unit with an overhang, the tailgate can be removed. Unlatch tailgate and remove support cables from the retainer pins. Raise right side of tailgate until the lower right side pivot clears the hanger bracket. Then slide the tailgate to the right to remove. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Carbon Monoxide Warning Vehicles Equipped With A Cap or Slide-In Campers...
Page 131 INSTRUMENT PANEL AND CONTROLS CONTENTS Instruments And Controls ....134 Instrument Cluster ..... . 135 Instrument Cluster Description .
Page 132 132 INSTRUMENT PANEL AND CONTROLS Operating Instructions - Satellite Radio — If Equipped ......153 Sales Code RAQ –...
Page 133 Remote Sound System Controls — If Equipped . . 172 Radio Operation ..... . 172 CD Player ......173 Compact Disc Maintenance .
Page 134: Instruments And Controls
134 INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS...
Page 135: Instrument Cluster
INSTRUMENT PANEL AND CONTROLS 135 INSTRUMENT CLUSTER...
Page 136: Instrument Cluster Description
136 INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Temperature Gauge The temperature gauge indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operat- ing satisfactorily.
Page 137 left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less. There is a pointer on the side of this symbol that indicates the side that your fuel filler door is located.
Page 138 138 INSTRUMENT PANEL AND CONTROLS CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off.
Page 139 11. Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on.
Page 140 140 INSTRUMENT PANEL AND CONTROLS range (PRND21). If the PRNDL displays only the char- acters PRND21 (no boxes), have the system checked by an authorized dealer. 16. Trip Odometer The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button.
Page 141 18. Transmission Temperature Indicator This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing. If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEU- TRAL until the light goes off.
Page 142 142 INSTRUMENT PANEL AND CONTROLS 21. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
Page 143: Electronic Digital Clock
24. SVC (Service) 4WD Indicator The SVC 4WD lights will come on when the ignition key is turned to the ON position and will stay on for 2 seconds. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required.
Page 144: Clock Setting Procedure
144 INSTRUMENT PANEL AND CONTROLS display. On the AM/FM/CD (single-disc) radio only one of the two, time or frequency is displayed. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune / Audio control.
Page 145: Electrical Disturbances
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
Page 146: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
146 INSTRUMENT PANEL AND CONTROLS SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. REF Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 147 Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 148 148 INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes.
Page 149 Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
Page 150: Operation Instructions - Cd Mode
150 INSTRUMENT PANEL AND CONTROLS Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
Page 151 SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Page 152: Operation Instructions - Auxiliary Mode
152 INSTRUMENT PANEL AND CONTROLS Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 153: Operating Instructions - Hands Free Phone - If Equipped
TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for 5 seconds. RW/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped).
Page 154: Sales Code Raq - Am/Fm/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (Ves) Capabilities
154 INSTRUMENT PANEL AND CONTROLS SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. RAQ Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC...
Page 155 Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player, Satellite Radio, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 156 156 INSTRUMENT PANEL AND CONTROLS Time Button Press the time button and the time of day will be displayed for 5 seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune / Audio control.
Page 157 Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL- ANCE will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
Page 158 158 INSTRUMENT PANEL AND CONTROLS Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is Jazz displayed, the radio will be tuned to the next frequency News...
Page 159: Operation Instructions - (Cd Mode For Cd Audio Play)
You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET/DIR button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 160 160 INSTRUMENT PANEL AND CONTROLS CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
Page 161: Load/Eject Button
LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC.
Page 162 162 INSTRUMENT PANEL AND CONTROLS TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed.
Page 163: Notes On Playing Mp3 Files
Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
Page 164 164 INSTRUMENT PANEL AND CONTROLS Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Page 165: Operation Instructions
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: •...
Page 166 166 INSTRUMENT PANEL AND CONTROLS LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
Page 167: Satellite Radio - If Equipped
AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
Page 168: System Activation
168 INSTRUMENT PANEL AND CONTROLS System Activation NOTE: Your vehicle’s radio must be on and in satellite mode when the activation process takes place. To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com.
Page 169: Selecting Satellite Mode In Ref, Raq, And Rak
ESN/SID Access With RAQ and RAK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will display. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
Page 170: Selecting A Channel
170 INSTRUMENT PANEL AND CONTROLS Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
Page 171: Pty Button Seek
one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected.
Page 172: Remote Sound System Controls - If Equipped
172 INSTRUMENT PANEL AND CONTROLS REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push button in the center.
Page 173: Cd Player
The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set push-buttons. CD Player Pressing the top of the switch once will go to the next track on the CD.
Page 174: Sound Box Operation
174 INSTRUMENT PANEL AND CONTROLS NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service.
Page 175: Radio Operation And Cellular Phones
RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 176 176 INSTRUMENT PANEL AND CONTROLS at the top of the snowflake button shows that the air conditioning is on. Press the button a second time to turn the air conditioning off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on.
Page 177 Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel. NOTE: The air conditioner compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 178: Operating Tips
178 INSTRUMENT PANEL AND CONTROLS Temperature Control The rotary knob at the center of the control panel controls the temperature of the inte- rior air. You can choose your degree of comfort by rotating the knob. The coldest tem- perature setting is to the ex- treme left (blue region) and the warmest setting is to the extreme right (red region) of...
Page 179 drive with the windows open for the first few minutes. Once the hot air has been expelled, close the windows and turn the mode selector to the Recirculation Panel Mode or Recirculation Mode Bi-level position. When a comfortable condition has been reached, choose a mode position and adjust the temperature control knob and blower speed as necessary to maintain comfort.
Page 180 180 INSTRUMENT PANEL AND CONTROLS Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration of engine coolant to distilled water is recommended.
Page 181: Operation Tips Chart
INSTRUMENT PANEL AND CONTROLS 181 Operation Tips Chart...
Page 183 STARTING AND OPERATING CONTENTS Starting Procedures ..... 187 Manual Transmission ....187 Automatic Transmission .
Page 184 184 STARTING AND OPERATING NV 244 Generation II Transfer Case Operating Information / Precautions ....205 Shifting Procedure - NV 244 Generation II Transfer Case ......209 Limited-Slip Rear Axle Differential—...
Page 185 Alignment And Balance ....234 Supplemental Tire Pressure Information – If Equipped ......235 Tire Chains .
Page 186 Snowplow ......264 Dodge Dakota Models ....264 Recreational Towing (Behind Motorhome, Etc.) .
Page 187: Starting Procedures
STARTING PROCEDURES The starter should not be operated for more than 15 second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Be sure to turn off the engine if you want to rest or sleep in your car.
Page 188: Normal Starting
188 STARTING AND OPERATING Normal Starting Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
Page 189: After Starting
WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 190: Automatic Transmission
190 STARTING AND OPERATING The engine block heater cord is located at the right front of the engine compartment for all engine applications. WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow-...
Page 191: Brake/Transmission Interlock System
WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 192 192 STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park).
Page 193 “R” Reverse Use this range only after the vehicle has come to a complete stop. “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle.
Page 194 194 STARTING AND OPERATING • transmission has reached normal operating tempera- ture. NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level.
Page 195 performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
Page 196: Manual Transmission
196 STARTING AND OPERATING transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position.
Page 197: Recommended Shift Speeds
To shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop. Reverse has a crash-through lockout feature. In order to get into the reverse gate you should start in neutral 3/4 and move rapidly into the reverse gate in one swift motion.
Page 198: Downshifting
198 STARTING AND OPERATING Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed.
Page 199: Four-Wheel Drive Operation
FOUR-WHEEL DRIVE OPERATION NV233/243 GII Transfer Case Operating Information/Precautions The NV233/243 is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. The NV233/243 transfer case provides 4 mode positions: 2 (rear) wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral.
Page 200 200 STARTING AND OPERATING (2WD). If the indicator light is on, the desired position (4WD LOCK and 4WD LOW) has been obtained. If One or More Shift Requirements are not Met: 1. An indicator light will flash. 2. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met.
Page 201 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
Page 202: Shifting Procedure - Nv233/243 Transfer Case
202 STARTING AND OPERATING 4WD LOCK 4 Wheel Drive Lock (4WD LOCK) Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose or slippery road surfaces only. 4WD LOW 4 Wheel Drive Low (4WD LOW) Range - Low speed 4 wheel drive.
Page 203 return the control knob back to the original position, make certain all shift requirements have been met, wait five (5) seconds and try the shift again. 2WD to 4WD LOCK or 4WD LOCK to 2WD Rotate the 4WD Control Switch to the desired position. Shifts between 2WD and 4WD LOCK can be done with the vehicle stopped or in motion.
Page 204 204 STARTING AND OPERATING 2. Shift the transmission into NEUTRAL (depress clutch on manual transmissions). 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions).
Page 205: Nv 244 Generation Ii Transfer Case Operating
NV 244 Generation II Transfer Case Operating Information / Precautions The NV 244 Generation II is an electric shift transfer case and is operated by the 4WD Control Switch, which is located on the instrument panel. The NV 244 Generation II transfer case provides 4 mode positions - Normal four-wheel-drive (4WD) high range, four-wheel-drive lock (4WD LOCK), four-wheel-drive low (4WD LOW) range, and neutral (N).
Page 206 206 STARTING AND OPERATING NOTE: The transfer case Neutral (N) position is to be used for recreational towing only. See Recreational Tow- ing section for specific procedures on shifting into and out of Neutral (N). Transfer Case Position Indicator Lights Transfer case position indicator lights are located on the instrument cluster.
Page 207 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 40 km/h (25 mph). Proper operation of four-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
Page 208 208 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position see the following informa- tion: Normal Four-Wheel-Drive High Range - Employs inter- axle differential. Allows front and rear wheels to rotate at different speeds. All road surfaces. 4WD LOCK Four-Wheel-Drive Lock (4WD LOCK)- Locks the transfer case inter-axle differential.
Page 209: Case
Shifting Procedure - NV 244 Generation II Transfer Case NOTE: The 4x4 system will not allow shifts between 4WD/ 4WD LOCK if the rear wheels are spinning (no traction). In this situation a position indicator light will flash and the original position indicator light will remain ON.
Page 210: Limited-Slip Rear Axle Differential- If Equipped
210 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to complete stop. 2.
Page 211: Driving On Slippery Surfaces
WARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface.
Page 212: Parking Brake
212 STARTING AND OPERATING PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. Be sure the parking brake is firmly set when parked and the gear-shift lever is in the PARK position.
Page 213: Brake System
WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or the vehicle may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury.
Page 214: Four-Wheel Anti-Lock Brake System
214 STARTING AND OPERATING The system remains operational in the four-wheel drive mode. The level of performance is reduced when the front brakes are locked up. This will cause the rear brakes to lock-up through the drivetrain, which may reduce the effectiveness of the anti-lock system.
Page 215 WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. STARTING AND OPERATING 215 WARNING! •...
Page 216: Power Steering
216 STARTING AND OPERATING When you are in a severe braking condition involving use of the Anti-lock Brake System, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system reverting to the base brake system.
Page 217: Rocking The Vehicle
WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
Page 218: Tire Safety Information
218 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 219 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 220 220 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 221: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 222: Tire Loading And Tire Pressure
222 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 223 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 224 224 STARTING AND OPERATING passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = 650 lbs.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
Page 225 STARTING AND OPERATING 225...
Page 226: Tires - General Information
226 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 227: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 228 228 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 229: Radial-Ply Tires
Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 230: Compact Spare Tire - If Equipped
230 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 231: Limited Use Spare - If Equipped
Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
Page 232: Tread Wear Indicators
232 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
Page 233: Life Of Tire
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
Page 234: Alignment And Balance
234 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 235: Supplemental Tire Pressure Information - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION – IF EQUIPPED A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 236 236 STARTING AND OPERATING CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage.
Page 237: Snow Tires
CAUTION! • Do not use tire chains on vehicles equipped with tires other than P245/70R16. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. • Do not use tire chains on the front wheels of your vehicle.
Page 238: Fuel Requirements
238 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 239: Reformulated Gasoline
Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular”...
Page 240: Mmt In Gasoline
240 STARTING AND OPERATING CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. NOTE: 4.7L Engine — If Equipped , is now rated for E85 Ethanol use.
Page 241: Materials Added To Fuel
Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. There- fore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s...
Page 242: Carbon Monoxide Warnings
242 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 243: Adding Fuel
ADDING FUEL Fuel Cap Holder NOTE: If fuel is poured from a portable container, the container should have a flexible nozzle long enough to extend into the fuel filler tube. STARTING AND OPERATING 243 CAUTION! To avoid fuel spillage and overfilling, do not “top off”...
Page 244: Fuel Filler Cap (Gas Cap)
244 STARTING AND OPERATING WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle or on a truck bed. You could be burned. Always place gas containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door.
Page 245: Flexible Fuel- If Equipped
FLEXIBLE FUEL— IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel ve- hicles only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Un- leaded Gasoline Only. This section only covers those subjects that are unique to these vehicles.
Page 246: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
246 STARTING AND OPERATING For best results, a refueling pattern that alternates be- tween E-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that • you do not switch when the fuel gauge indicates less than 1/4 full •...
Page 247: Cruising Range
Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel con- sumption. You can expect your MPG and your driving range to decrease by about 30% compared to gasoline operation. Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol.
Page 248 248 STARTING AND OPERATING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture.
Page 249: Curb Weight
Each axle GAWR is determined by the component in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle’s GVWR. Tire Size This is the minimum allowable tire size for your vehicle.
Page 250 250 STARTING AND OPERATING or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store heavier items down low and be sure that the weight is distributed equally.
Page 251: Trailer Towing
after the vehicle has been weighed both in its curb weight condition, and in its loaded and ready for operation condition. Gross Vehicle Weight Rating (GVWR) 6500 LBS. STARTING AND OPERATING 251 TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
Page 252 252 STARTING AND OPERATING Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its loaded and ready for operation condition. The recom- mended way to measure GTW is to put your fully loaded trailer on a vehicle scale.
Page 253 Frontal Area The maximum height and maximum width of the front of a trailer. TSC (Trailer Sway Control) – If Equipped • Trailer Sway Control – Electronic TSC uses sensors in the vehicle to recognize a swaying trailer and will take the appropriate actions to attempt to stop the sway.
Page 254 254 STARTING AND OPERATING used in accordance with the manufacturers’ directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety. The addition of a friction / hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.
Page 255 STARTING AND OPERATING 255 Weight Distributing Hitch System Improper Adjustment of Weight Distributing System Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin.
Page 256: Trailer Hitch Classification
256 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to...
Page 257: Trailer Towing Weights
• http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 258: Towing Requirements
258 STARTING AND OPERATING • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
Page 259 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 260 260 STARTING AND OPERATING 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements —...
Page 261 actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 262: Towing Tips
262 STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7- Pin Connector Towing Tips...
Page 263 If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “TOW HAUL”...
Page 264: Snowplow
Maintenance section of this manual for more informa- tion. SNOWPLOW Dodge Dakota Models NOTE: Do not use Dodge Dakota Models for snowplow applications. WARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end of your vehicle.
Page 265: Recreational Towing (Behind Motorhome, Etc.)
CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual STARTING AND OPERATING 265 RECREATIONAL TOWING (BEHIND...
Page 266 266 STARTING AND OPERATING CAUTION! The transfer case must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection but- ton is located on the lower left hand corner of the 4WD Control Switch. Shifts into and out of transfer case Neutral (N) can take place with the selector switch in any mode position.
Page 267 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 4 seconds. 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. STARTING AND OPERATING 267 9.
Page 268 268 STARTING AND OPERATING during the 4 second timer, then the Neutral (N) indicator light will flash continuously until all requirements are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
Page 269 8. After the Neutral (N) indicator light turns off release the Neutral (N) button. 9. After the Neutral (N) button has been released the transfer case will shift to the position identified by the selector switch. 10. Start the engine. Shift the automatic transmission into Drive (D), or place the manual transmission in 1st gear and momentarily release the clutch, to verify that the transfer case has engaged.
Page 270: Equipment Identification Plate
270 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission position.
Page 271: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....272 Adding Fuel ......272 Changing A Flat Tire .
Page 272: Hazard Warning Flasher
272 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers.
Page 273: Changing A Flat Tire
WARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed.
Page 274 274 WHAT TO DO IN EMERGENCIES Jack Stowage Location Extended Cab Jack Stowage Location Extended Cab...
Page 275: Removing The Spare Tire
Jack Stowage Location Double Cab WHAT TO DO IN EMERGENCIES 275 WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure.
Page 276 276 WHAT TO DO IN EMERGENCIES Steps for Removing the Spare Tire • Remove the jack from the stowage compartment using the supplied finger assist tool. • Remove the finger assist tool from jack and set aside until jack is stowed. •...
Page 277 Turning Lug Wrench and Extension It is recommended that you stow the flat or spare to avoid tangling the loose cable. WHAT TO DO IN EMERGENCIES 277 Spare Tire Stowage Location NOTE: The winch mechanism is designed for use with the jack extension tube only.
Page 278: Tire Changing Procedure
278 WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 279 • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
Page 280 280 WHAT TO DO IN EMERGENCIES positions shown with the drive tubes extending to the rear. Connect the jack tube extension and wheel wrench. Left Rear Jacking Location Right Rear Jacking Location NOTE: Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required.
Page 281 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 5. Remove the wheel nuts and pull the wheel off. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel.
Page 282 282 WHAT TO DO IN EMERGENCIES WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
Page 283: Jump Starting
JUMP STARTING WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or cloth- ing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the con- taminated area immediately with large quantities of water.
Page 284 284 WHAT TO DO IN EMERGENCIES 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result.
Page 285: Emergency Tow Hooks - If Equipped
WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. EMERGENCY TOW HOOKS —...
Page 286: Towing A Disabled Vehicle
286 WHAT TO DO IN EMERGENCIES WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing.
Page 287: Two-Wheel Drive Vehicles
Two-Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF position along with the front wheels raised and the rear wheels on the ground. The speed must not exceed 30 mph (50 km/h) and the distance must not exceed 15 miles (25 km).
Page 289: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 3.7L/4.7L Engine Compartment ... . . 292 Onboard Diagnostic System — OBD II ..293 Loose Fuel Filler Cap Message ... . 293 Emissions Inspection And Maintenance Programs .
Page 290 290 MAINTAINING YOUR VEHICLE Front Suspension Ball Joints ....306 Drive Shaft Constant Velocity Joints ..307 Body Lubrication ..... 307 Windshield Wiper Blades .
Page 291 License Lamps ..... . . 343 Fog Lamps ......345 Fluids And Capacities .
Page 292: 3.7L/4.7L Engine Compartment
292 MAINTAINING YOUR VEHICLE 3.7L/4.7L ENGINE COMPARTMENT...
Page 293: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 294: Emissions Inspection And Maintenance Programs
294 MAINTAINING YOUR VEHICLE cap until a clicking sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started.
Page 295: Replacement Parts
3. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 4. Approximately 15 seconds later, one of two things will happen: a. The MIL light will blink for approximately 5 sec- onds and then remain on until the first engine crank or the key is turned off.
Page 296: Dealer Service
296 MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 297: Engine Oil
could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Engine Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
Page 298 298 MAINTAINING YOUR VEHICLE Change Engine Oil Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures are below 32°F (0°C). •...
Page 299 Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner. The crankcase ventilation system should also be checked periodically. Make sure that these units are always clean.
Page 300: Engine Oil Filter
300 MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Synthetic Engine Oils You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed.
Page 301: Drive Belts - Check Condition And Tension
Drive Belts — Check Condition and Tension Belt tension is controlled by means of an automatic tensioner. No belt tension adjustments are required. However, belt and belt tensioner condition should be inspected at the specified intervals, and replaced if re- quired.
Page 302: Engine Air Cleaner Filter
302 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe con- ditions, the filter element should be inspected periodi- cally and replaced if necessary at the intervals shown on Schedule “B”.
Page 303 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 304: Maintenance Free Battery
304 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle.
Page 305: Air Conditioner Maintenance
CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case. •...
Page 306: Power Steering - Fluid Check
306 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 307: Drive Shaft Constant Velocity Joints
Drive Shaft Constant Velocity Joints All four wheel drive models are equipped with four constant velocity joints. Periodic lubrication of these joints is not required. However, the joint boot should be inspected for external leakage or damage periodically. If external leakage or damage is evident, the joint boot and grease should be replaced immediately.
Page 308: Windshield Washers
308 MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Washers The fluid reservoir should be checked for fluid level at regular intervals.
Page 309: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken,...
Page 310: Cooling System
310 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radia- tor is hot.
Page 311 Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 312 312 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 313 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 314 314 MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 315: Emission Related Components
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Emission Related Components Fuel System Hoses And Vapor/Vacuum Harnesses When the vehicle is serviced for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 316: Brake System
316 MAINTAINING YOUR VEHICLE attempt to clean the oil PCV valve! Check ventilating hose for indication of damage or plugging with deposits. Replace if necessary. Brake System Power Disc Brakes (Front) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material.
Page 317 WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
Page 318: Clutch Hydraulic System
318 MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance free system.
Page 319 3. Fully apply the parking brake and press the brake pedal. 4. Place the gear selector momentarily in each gear position ending with the lever in P (Park). 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6.
Page 320 Authorized Dodge Dealer or Service Center. It is important that the transmission fluid be maintained at the correct level and that it be drained and refilled as specified.
Page 321: Transfer Case
Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low. Have the transfer case serviced immediately. CAUTION! Damage may result from operation of the vehicle with low transfer case fluid. The transfer case fluid should be drained and refilled at the intervals specified.
Page 322: Selection Of Lubricating Grease
322 MAINTAINING YOUR VEHICLE differential. Rear axle fluid level should be 1/4 (6.4mm) below filler plug for 8 1/4”, and 9 1/4 axles. Front Axle Front Axle fluid level should be at the bottom of the fill plug. Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for chassis...
Page 323: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 324 324 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
Page 325 Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopar Wheel Cleaner or select a nonabra- sive, non-acidic cleaner.
Page 326 326 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean.
Page 327: Fuses (Power Distribution Center)
1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
Page 328 328 MAINTAINING YOUR VEHICLE These power distribution centers house new plug-in “Cartridge” fuses which replace all the in-line fusible links previously used. The power distribution centers also contain “Mini”fuses and plug-in “ISO” relays. These fuses and relays can be obtained from your dealer. Cartridge Mini Cavity...
Page 329 Cartridge Mini Cavity Fuse Fuse 20 Amp Horn Yellow 20 Amp ABS Feed (Valves) Yellow 20 Amp Fuel Pump Yellow 15 Amp Center High Mounted Blue Stop Lamp (CHMSL) 20 Amp Cabin Compartment Yellow Node (CCN) Door Locks/Brake Transmis- sion Shift Interlock (BTSI) 25 Amp Audio Amp...
Page 330 330 MAINTAINING YOUR VEHICLE Cartridge Mini Cavity Fuse Fuse 30 Amp Front Control Module Pink (FCM) 2 (Ext. Light # 2) 40 Amp HVAC Blower Motor Green 10 Amp Ignition UNLK/RN/ST 10 Amp Crank 20 Amp Run/Start Blue 30 Amp Starter Solenoid Pink Spare...
Page 331 Cartridge Mini Cavity Fuse Fuse Spare 10 Amp Cabin Compartment Node (CCN) Accessory (ACC) Feed 10 Amp Heated Seats 20 Amp Airbag System # 2 Yellow 20 Amp Heated Seats Yellow 10 Amp HVAC Module 10 Amp ABS Module 20 Amp Front Control Module Yellow (FCM) 3 (Reverse...
Page 332: Vehicle Storage
332 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Power Distribution Center (PDC).
Page 333: Bulb Replacement
MAINTAINING YOUR VEHICLE 333 BULB REPLACEMENT Headlamps Removing Headlamp Assembly Removing Attaching Screw...
Page 334 334 MAINTAINING YOUR VEHICLE Removing Headlamp Assembly 1. Open the hood. 2. Remove the 3 screws attaching the headlamp housing to the inner panel. 3. Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel. 4.
Page 335 MAINTAINING YOUR VEHICLE 335 Unlocking Connector Removing Headlamp from Assembly...
Page 336 336 MAINTAINING YOUR VEHICLE Removing Headlamp Bulb Disconnecting Headlamp Bulb Connector 6. Reverse procedure to install new Headlamp bulb into the headlamp assembly. NOTE: These are Halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life.
Page 337: Front Park And Turn Signal Lamp
Front Park and Turn Signal Lamp. • Open the hood. • Remove the (3 ) screws attaching the headlamp hous- ing to the inner panel. • Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel. NOTE: It is not necessary to disconnect the connector to replace this bulb.
Page 338: Rear Side Marker, Taillamps/Stoplamp, And Turn Signal Bulbs - Replacement
338 MAINTAINING YOUR VEHICLE • Rotate bulb socket 1/4 turn and remove socket from housing. • Pull bulb straight from socket. • Reverse procedure to install new turn signal bulb. Disconnecting Turn Signal Connector Rear Side Marker, Taillamps/Stoplamp, and Turn Signal Bulbs —...
Page 339 MAINTAINING YOUR VEHICLE 339 2. Pull the taillamp housing straight out from the body. 3. Rotate the bulb socket counterclockwise to from the housing. Pulling Housing From Body Rotating Bulb Socket From Housing...
Page 340 340 MAINTAINING YOUR VEHICLE 4. Pull bulb straight out of socket. Pulling Bulb From Socket 5. Reverse Procedure to install bulb and housing. Place the two raised blocks passed the body. Sliding Raised Blocks Past Body...
Page 341: Center High-Mounted Stoplamp And Cargo Lamp
MAINTAINING YOUR VEHICLE 341 2. Remove housing from Cab Center High-Mounted Stoplamp And Cargo Lamp 1. Remove the two (2) screws holding the housing/lens to the body as shown. Removing Housing from Cab Removing Screws...
Page 342 342 MAINTAINING YOUR VEHICLE 3. Remove connector from housing tab for more clear- ance. Removing Connector from Tab 4. Turn desired bulb socket ⁄ and bulb from housing. Removing Socket From Housing turn and remove socket...
Page 343: License Lamps
5. Pull desired bulb straight from the socket. Pulling Bulb From Socket • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 6. Reverse procedure for installation of bulbs and hous- ing. MAINTAINING YOUR VEHICLE 343 License Lamps 1.
Page 344 344 MAINTAINING YOUR VEHICLE 2. Rotate the socket 1/4 turn counterclockwise. Rotating Socket 3. Pull bulb from socket. Pulling Bulb From Socket 4. Reverse procedure for installation.
Page 345: Fog Lamps
Fog Lamps 1. Disconnect connector from fog lamp by raising wire harness lock tab and pulling on wire harness connector. FLUIDS AND CAPACITIES Fuel 3.7L/4.7L, 87 Octane 4.7L HO, 91 Octane, Recommended Not Required Engine Oil (with filter) 3.7L, SAE 5W-20, API Certified 4.7L, SAE 5W-20, API Certified 4.7L HO, SAE 5W-20, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle...
Page 346: Fluids, Lubricants And Genuine Parts
346 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection 3.7L/4.7L Fuel Selection 4.7L HO Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent.
Page 347: Chassis
Chassis Component Automatic Transmission Manual Transmission (Getrag 238) Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant (MS-9763).
Page 349 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..350 Maintenance Schedules ....350 Schedule “B” ......353 Schedule “A”...
Page 350: E Emission Control System Maintenance
350 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 351 • Off-road or desert operation. • Heavy Loading • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B”...
Page 352 352 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 353: Schedule "B" 353
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 354 354 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if neces- sary.
Page 355 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings.
Page 356 356 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 357 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 358 358 SCHEDULE “B” Miles (Kilometers) Drain and refill automatic transmission fluid and change main sump filter (4.7L). * Inspect transfer case fluid (4X4). Flush and replace engine coolant at 60 months, or 102, 000 miles (170 000 km) whichever comes first. 48,000 51,000 54,000...
Page 359 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 360 360 SCHEDULE “B” Miles (Kilometers ) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4).
Page 361 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Flush and replace engine coolant, if not done at 60 months. Change rear axle fluid. Change front axle fluid (4X4).
Page 362 362 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings.
Page 363 Miles (Kilometers) Drain and refill automatic transmission fluid, change filter (3.7L). * Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. (4.7L). * Flush and replace engine coolant, if not re- placed at 102,000 miles (170 000 km).
Page 364: 364 Schedule "A
364 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as neces- sary.
Page 365 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (170 000 km).
Page 366 366 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 367 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill tranfer case fluid (4X4). Flush and replace engine coolant, if not done at 60 months. Flush and replace engine coolant, if not done at 102,000 miles (170 000 km) Inspect brake linings.
Page 368 368 SCHEDULE “A” ** This maintenance is recommended by the manufac- turer to the owner, but not required to maintain the emissions warranty. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts.
Page 369: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......370 Prepare For The Appointment .
Page 370: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 371 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 372 372 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 373: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 374: Publication Order Forms
374 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 375: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 376: Temperature Grades
376 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Page 377 INDEX...
Page 378 378 INDEX Adding Fuel ......243,272 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 302 Air Conditioner Maintenance .
Page 379 Axle Lubrication (Axle Fluid) ....321 Ball Joints ......306 Battery .
Page 380 380 INDEX Catalytic Converter ..... . 302 CD (Compact Disc) Player ....146,154 Cellular Phone .
Page 381 Selection of Coolant (Antifreeze) ..311,345,346 Temperature Gauge ..... 136 Cruise Control (Speed Control) ....99 Cup Holder .
Page 382 382 INDEX Emission Related Components ....315 Engine Air Cleaner ......302 Block Heater .
Page 383 Maintenance ......247 Replacement Parts ..... 247 Starting .
Page 384 384 INDEX Fuel ....... . 136 Odometer ......140 Speedometer .
Page 385 Inflation Pressure Tires ....235 Inside Rearview Mirror ....79 Instrument Cluster .
Page 386 386 INDEX High Beam/Low Beam Select ....96 Instrument Cluster ..... 136 Intensity Control .
Page 387 Manual Transmission ....187,196,318 Fluid Level Check ..... . 318 Lubricant Selection .
Page 388 388 INDEX Overheating, Engine ..... . 138 Owner’s Manual (Operator Manual) ..374 Panic Alarm .
Page 389 Radio (Sound Systems) ....146,154 Rear Axle (Differential) ....321 Rear Window .
Page 390 390 INDEX Child Restraint ..... . . 58,59 Extender ......43 Front Seat .
Page 391 Speed Control (Cruise Control) ....99 Speedometer ......138 Starting .
Page 392 392 INDEX Chains ......235 Changing ......273 Compact Spare .
Page 393 Transaxle ......190 Automatic ......12,190 Manual .
Page 394 394 INDEX Weight Load Carrying ....247 Wheel Alignment and Balance ....234 Wheel and Wheel Trim .
Page 395 NOTES...
Page 396 NOTES...
Page 397 NOTES...
Page 398 NOTES...
Page 399 NOTES...
Page 400 NOTES...

This manual is also suitable for:

2007 nd dakota

Dodge 2007 Dakota Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Instrument Panel and Controls

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2007 Dakota

Summary of Contents for Dodge 2007 Dakota