Dodge 2006 JR41 Stratus Sedan Owner's Manual

Dodge 2006 stratus automobile owner's manual

page of 296

/ 296
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

SECTION

INTRODUCTION

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING YOUR INSTRUMENT PANEL

STARTING AND OPERATING

WHAT TO DO IN EMERGENCIES

MAINTAINING YOUR VEHICLE

MAINTENANCE SCHEDULES

IF YOU NEED CONSUMER ASSISTANCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277

INDEX

TABLE OF CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269

PAGE

Table of Contents

Chapters

Table of Contents

Summary of Contents for Dodge 2006 JR41 Stratus Sedan

Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
This number also ap- pears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label as a convenient record of your vehicle identification number and optional equipment.
Page 7: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS Sentry Key — If Equipped ....9 Replacement Keys ..... . 9 Customer Key Programming .
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tamper Alert ......19 Security System Manual Override ...19 Trunk Lock And Release .
Page 9: Things To Know Before Starting Your Vehicle 7
SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for 2 seconds then shut off.
Page 10: Customer Key Programming
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure.
Page 11: Illuminated Entry System
ILLUMINATED ENTRY SYSTEM The interior lights will come on when you open any door, unlock the vehicle with the remote keyless entry (if so equipped) or central unlock (if so equipped). They will remain on for about 30 seconds after all doors are closed then fade to off.
Page 12: Power Door Locks
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks There is a door lock switch on each front door trim panel located to the front of the door handle. Press this switch to lock or unlock the four doors. Power Door Lock Switch If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors...
Page 13: Central Locking - If Equipped
Central Locking — If Equipped All vehicle doors are locked with the first turn of the key to the LOCK position. The double activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors at once.
Page 14: Automatic Unlock On Exit - Only Available If
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door lock switch to lock the doors. Power Door Lock Switch 4. A single chime will indicate the completion of the programming. Automatic Unlock on Exit — Only Available if Automatic Door Locks are Enabled This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK...
Page 15: Remote Keyless Entry - If Equipped
WARNING! Avoid trapping anyone in the vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Child Lock Control NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), lower the window and open the door with the outside door handle.
Page 16: To Lock The Doors
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Press and hold the Unlock button on the transmit- ter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the LOCK button.
Page 17: Panic Alarm
2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Trunk button. 3. Release both buttons. Panic Alarm The panic mode unlocks the driver’s door, turns on the interior lights, flashes the headlights, and sounds the horn for about 3 minutes or until the alarm is turned off.
Page 18: Transmitter Battery Service
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undes- ired operation If your Remote Lock Control fails to operate from a normal distance, check for these two conditions: 1.
Page 19: Vehicle Theft Alarm
VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes. For the first three minutes the horn will sound and the headlights and interior lights will flash. Then the horn will stop and if the source of the trigger is still present, the lights will continue to flash for another 15 minutes.
Page 20: Trunk Lock And Release
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE Trunk Release Button Use the key or the Remote Keyless Entry Transmitter to open the trunk from outside the vehicle. From inside the car the trunk lid can be released by depressing the Trunk Release Button located on the instrument panel to the left of the steering wheel.
Page 21: Trunk Internal Emergency Release
Trunk Internal Emergency Release Emergency Release NOTE: As a security measure, a Trunk Internal Emer- gency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
Page 22: Occupant Restraints
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power windows while operating the power window switch. Such entrapment may result in serious injury or death.
Page 23: Lap/Shoulder Belts
Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
Page 24 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 25 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 27: Seat Belt Pretensioners
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 28: Enhanced Driver Seat Belt Reminder System (Beltalert)
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt.
Page 29: Seat Belts And Pregnant Women
The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy.
Page 30: Driver And Right Front Passenger Supplemental Restraint System (Srs) - Airbag
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag Front Airbag Components This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
Page 31 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are not there to protect you. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the vehicle seat belt (see section on “Child Restraint”) should be secured in the rear seat in child restraints or belt- positioning booster seats. Older children who do not use child restraints or belt- positioning booster seats should ride properly buckled up in the rear seat.
Page 33 • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters • Left and Right Window Bags Above Side Windows — If Equipped • Left and Right Side Impact Sensors — If Equipped •...
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 35 They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE where the window bag inflates. This especially applies to children. The window bag is only about 3 cm) thick when it is inflated. Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it.
Page 37 Children 12 years and under should ride properly buck- led up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.
Page 39 NOTE: For additional information refer to www.seatcheck.org or call 1–866–SEATCHECK. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now avail- able. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to also have features for installation using the vehicle’s seat...
Page 41 Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child restraint rearward and downward into the seat, removing slack in the straps according to the child restraint manufacturer’s instructions. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
Page 43 In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it.
Page 44: Engine Break-In Recommendations
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instruc- tions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Page 45: Safety Tips
SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. •...
Page 46: Periodic Safety Checks You Should Make Outside The Vehicle
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the bulb is not lit during starting, have it replaced.
Page 47: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Console Features ..... . .50 Console Features — Without Heated Seats ..50 Console Features —...
Page 48 48 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) ..62 Lights-On Reminder ....62 Fog Lights —...
Page 49 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 49 Sunshade Operation ....75 Sunroof Fully Closed ....76 Wind Buffeting .
Page 50: Console Features
50 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Console Features — Without Heated Seats Console The front console has two cup holders in the front and a storage bin. An optional removable ashtray may be located in the driver’s side cup holder. The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover.
Page 51: Console Features - With Heated Seats
Console Features — With Heated Seats Console The front console has two cup holders. An optional removable ashtray may be located in the driver’s side cup holder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover.
Page 52: Mirrors
52 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Adjusting Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 53: Electric Remote-Control Mirrors- If Equipped
CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Electric Remote-Control Mirrors— If Equipped Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel to the left of the steering wheel.
Page 54: Outside Mirror - Passenger's Side
54 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are.
Page 55 Manual Seat Adjuster After releasing the adjusting bar, apply forward and rearward body pressure to be sure the seat is latched. Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever.
Page 56: Power Seats - If Equipped
56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor. Use the front switch to move the seat up, down, forward, rearward, or to tilt the seat. The rear switch controls the seatback recliner.
Page 57: Folding Rear Seat
Adjustable Head Restraint Folding Rear Seat To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seat back to the upright position be sure the seat back is latched.
Page 58: To Open And Close The Hood
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood Release Lever Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood.
Page 59: Lights
WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Interior Lights The map/courtesy lights come on when a door is opened and the panel lamp dimmer switch (located on the turn signal control stalk) is in any detent except fully counter-...
Page 60: Front Map/Reading Lights - If Equipped
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (full-circle). This feature bright- ens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Front Map/Reading Lights —...
Page 61: Multi-Function Control Lever
Multi-Function Control Lever Multi-Function Lever The Multi-Function lever controls the operation of the headlights, turn signals, headlight beam select switch, instrument panel light dimming, courtesy lights, passing lights, dome light and fog lights. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the control lever to the first detent for parking light operation.
Page 62: Automatic Headlights-If Equipped
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights—If Equipped This system automatically turns your headlights on at a preset level of outdoor lighting. Turn the end of the control lever to the third detent to turn the system on. When the system is on, the headlight delay feature is also on.
Page 63: Headlight Beam Select Switch
Headlight Beam Select Switch Pull the turn signal lever towards you to switch the headlights to HIGH beam. Pull the turn signal lever a second time to switch the headlights to LOW beam. Flash to Pass You can signal another vehicle with your headlights by lightly pulling the turn signal lever toward the steering wheel.
Page 64: Mist
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several cycles after the lever is released, and then resume the intermit- tent interval previously selected.
Page 65: Traction Control- If Equipped
Tilt Steering Column Control WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 66: Electronic Speed Control- If Equipped
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Traction Control System is enabled each time the ignition switch is turned On. This will occur even if you used the switch to turn the system off before powering down or turning the ignition to Lock. ELECTRONIC SPEED CONTROL—...
Page 67: To Deactivate
To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory. Pushing the ON/OFF button or turning off the ignition turns the speed control system off and erases the memory. To Resume Speed: To resume a previously set speed, push and release the RESUME/ACCEL button.
Page 68 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When Climbing A Hill If vehicle speed drops 3 mph (5 km/h) below the Speed Control set speed, the transaxle will downshift to third gear. Under severe conditions the transaxle may down- shift again to second gear. The transaxle will upshift to fourth gear after the vehicle has reached the top of the hill.
Page 69: Garage Door Opener - If Equipped
GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system;...
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 71: Rolling Code" Programming
5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4.
Page 72: Canadian Programming/Gate Programming
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com.
Page 73: Operation
Operation Press and hold the desired button on the Universal Transceiver until the garage door or other device begins to operate. The light in the display shows that the signal is being transmitted. The hand held transmitter may also be used at any time. Reprogramming A Single Button 1.
Page 74: Power Sunroof - If Equipped
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors on the overhead console. Power Sunroof Controls WARNING! • Never leave children in a vehicle, with the keys in the ignition switch.
Page 75: Opening Sunroof - Manual
Opening Sunroof - Manual Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Fully Closed Press and hold the switch forward until the sunroof stops completely to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLET The power outlet is located in the lower center of your instrument panel.
Page 77: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....81 Instrument Cluster ..... .82 Instrument Cluster Description .
Page 78 78 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning ......94 Radio Data System (RDS) ....95 PTY (Program Type) Button .
Page 79 Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability ......103 Radio Operation .
Page 80 80 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode In RBB, RAH And RBK Radios ......116 Selecting Satellite Mode In RBP, RBU, RAZ, RB1 And RBQ Radios .
Page 81: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 81 INSTRUMENTS AND CONTROLS...
Page 82: Instrument Cluster
82 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 83: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Traction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON.
Page 84 84 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Airbag Light The light comes on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the bulb does not come on during starting, have the bulb replaced. If the light stays on, or comes on while driving, have the system checked by an authorized dealer.
Page 85 resume to full illumination. (See “EMISSIONS IN- SPECTION AND MAINTENANCE PROGRAMS” in the “MAINTAINING YOUR VEHICLE” section of your Owner Manual for more details). If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap or poor fuel quality may illuminate the light after engine start.
Page 86 86 UNDERSTANDING YOUR INSTRUMENT PANEL 13. Engine Temperature Warning Light This light warns of an overheated engine cool- ant condition. 14. Trip Odometer Button Press and release this button to change the display from odometer to trip odometer. The word TRIP will appear when in the trip odometer mode.
Page 87 17. Anti-Lock Warning Light — If Equipped This light monitors the Anti-Lock Brake System described elsewhere in this manual. This light will come on when the ignition key is turned to the RUN position and may stay on for several seconds. If the light does not come on, have the system checked by an authorized dealer.
Page 88 88 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the brake light on is danger- ous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.
Page 89: Compass, Temperature, And Trip Computer Display - If Equipped
COMPASS, TEMPERATURE, AND TRIP COMPUTER DISPLAY — IF EQUIPPED Trip Computer Display This feature allows you to choose between a compass / temperature display and one of five trip conditions being monitored. Control Buttons Step Button Use this button to choose or cycle through the five trip conditions.
Page 90: Trip Conditions
90 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Conditions Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- tion: (Average Fuel Economy) x (Fuel Remaining) This display cannot be reset.
Page 91 Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear on the display. After the vehicle has completed at least one complete circle in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished.
Page 92: Cigar Lighter/Ashtray
92 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than 40°F ( 40°C), the display will show 40°F/C. CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smok- er’s”...
Page 93: To Set The Clock
To Set The Clock: 1. Use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. 2. Press any other button to exit from the clock setting mode.
Page 94: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
94 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. RAZ Radio Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch.
Page 95: Radio Data System (Rds)
Radio Data System (RDS) The Radio Data System allows radio broadcasting sta- tions to send data signals on a subcarrier frequency which is added to the stereo signal. RDS was developed to give FM receivers user-friendly features, such as Program Service name (PS) and Program Type (PTY). Program Service name is typically used by the broad- caster to display the station’s name or call letters, for example WNIC .
Page 96: Balance
96 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Page 97: Am/Fm Selection
AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next.
Page 98: Seek Button
98 UNDERSTANDING YOUR INSTRUMENT PANEL be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year. Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection.
Page 99: Noise Reduction
Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off.
Page 100: Seek Button
100 UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
Page 101: Tape Cd Button
To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds.
Page 102 102 UNDERSTANDING YOUR INSTRUMENT PANEL The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace.
Page 103: Sales Code Rbb-Am/Fm Stereo Radio With Cassette Tape Player And Cd Changer Capability
SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY NOTE: The radio sales code is located on the lower left side of your radio faceplate. RBB Radio UNDERSTANDING YOUR INSTRUMENT PANEL 103 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on.
Page 104 104 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection.
Page 105: Mode Button
Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed.
Page 106: Cd Changer Control Capability - If Equipped
106 UNDERSTANDING YOUR INSTRUMENT PANEL beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automati- cally when a selection has been located.
Page 107 Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc.
Page 108: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
108 UNDERSTANDING YOUR INSTRUMENT PANEL • Disc inserted upside down • Damaged disc • Water condensation on optics SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate.
Page 109 To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button.
Page 110: Cd Player Operation
110 UNDERSTANDING YOUR INSTRUMENT PANEL Time Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1.
Page 111: Cd Changer Control Capability - If Equipped
beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal.
Page 112 112 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc.
Page 113: Disc Cd Changer - If Equipped
An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel.
Page 114: Playing Discs
114 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Insert the CD while the light above the chosen button is flashing and the two lights on either side of the slot are illuminated. 3. Upon insertion, the CD will begin to play, and both the button light and the lights in the corner of the loading slot will illuminate.
Page 115: Program Button 5
Press button 4 a second time to stop random play. Program Button 5 Press this button to play the previous disc. Time Button Press this button to switch between time of day and CD track time. Changing Modes While in the radio mode, if a cassette is loaded, press the Mode button to switch to the tape mode.
Page 116: System Activation
116 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Page 117: Selecting Satellite Mode In Rbp, Rbu, Raz, Rb1 And Rbq Radios
Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word SIRIUS appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds.
Page 118: Using The Pty (Program Type) Button (If Equipped)
118 UNDERSTANDING YOUR INSTRUMENT PANEL Using the PTY (Program Type) Button (If Equipped) Follow the PTY button instructions that apply to your radio. PTY Button SCAN When the desired program type is obtained, press the SCAN button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type.
Page 119: Remote Sound System Controls - If Equipped
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system.
Page 120: Cd Player - Single Disc In Radio
120 UNDERSTANDING YOUR INSTRUMENT PANEL If you press the switch up or down twice it plays the second selection, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode. CD Player —...
Page 121: Compact Disc Maintenance
Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport.
Page 122: Radio Operation And Cellular Phones
122 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. You may have a problem with CD-R (recordable) and CD-RW (recordable and writable) disks.
Page 123 Interior ATC Sensors There are two interior sensors in the vehicle. The Sun Sensor is mounted in the center of the instrument panel near the windshield glass. The In-Car Temperature Sen- sor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance.
Page 124 124 UNDERSTANDING YOUR INSTRUMENT PANEL Comfort Control Use this control to regulate the comfort inside the pas- senger compartment. Press the top of the switch to raise the temperature selection and the bottom of the switch to lower it. The comfort setting range is from Low, 60, 61,...to 89,90, Hi, for automatic temperature control.
Page 125 NOTE: The Recirc button light will blink if you try to use it in the Mix or Defrost modes. Air Direction Buttons (Mode) These buttons allow you to select from five air distribu- tion patterns. These buttons should be used only when you can not achieve comfort or visibility in Auto opera- tion.
Page 126 126 UNDERSTANDING YOUR INSTRUMENT PANEL Windshield Defrost Air is directed through the defrost outlets and side window demist outlets. A small amount of air also is directed through the floor outlets. Use this mode with maximum fan and comfort level settings for best windshield and side window defrosting.
Page 127 Hot Weather Automatic Recirculation The system will automatically recirculate the air inside the vehicle when the interior is very warm. This will provide maximum cooling. The system will also occa- sionally return to REC on hot, humid or very hot, dry days to maintain occupant comfort.
Page 128 128 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (ATC only)
Page 129: Manual Air Conditioning/Heater Control - If
NOTE: If the system is in the AUTO mode and the fan control is already rotated fully clockwise or fully coun- terclockwise, the control may have to be rotated to the middle and then to the desired fan setting for manual adjustment of fan speed.
Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. NOTE: If your air conditioning performance seems lower than expected, check the front of the air condition- ing condenser for an accumulation of dirt or insects.
Page 131 • Panel — Air Conditioning Outside air flows through the air condition- ing system and then through the outlets located in the instrument panel. • Bi-Level — Air Conditioning Outside air flows through the air condition- ing system and then through the outlets located in both the instrument panel and floor outlets.
Page 132 132 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Seat Outlets These outlets are located under the front seats and direct warm air to the rear seat passengers. Air is directed through these outlets when you select either the Floor, Bi-Level, or Mix modes. Rear Window Defroster The Rear Window Defroster button is located to the right of the Mode Control.
Page 133 NOTE: Do not use the recirculation mode as it will not clear windows under these conditions. Summer Operation Air conditioned vehicles must be protected with a high- quality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating.
Page 134 134 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (Manual A/C Control Only)
Page 135 UNDERSTANDING YOUR INSTRUMENT PANEL 135 Outside Air Intake Make sure the air intake, directly in front of the wind- shield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. Air Intake...
Page 137: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....140 Automatic Transaxle ....140 Manual Transaxle .
Page 138 138 STARTING AND OPERATING Tire Safety Information ....152 Tire Markings ......152 Tire Identification Number (TIN) .
Page 139 Fuel Requirements ....175 Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles ..176 Starting .
Page 140: Starting Procedures
140 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
Page 141: Extreme Cold Weather (Below -20°F Or -29°C)
Ignition Key Positions WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. STARTING AND OPERATING 141 CAUTION! Do not attempt to push or tow your vehicle to get it started.
Page 142: If Engine Fails To Start
142 STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” WEATHER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
Page 143: Automatic Transaxle
WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. AUTOMATIC TRANSAXLE Brake/Transmission Interlock This interlock system prevents you from moving the gear selector out of the Park position unless the brake pedal is pressed.
Page 144: Automatic Transaxle Ignition Interlock System
144 STARTING AND OPERATING CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 145: Four Speed Automatic Transaxle
Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrat- ing; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and preci- sion shifts will develop within a few shift cycles.
Page 146 146 STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P. Make sure it is in Park before leaving the vehicle.
Page 147: Parking Brake
NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance, fuel economy, and extend transaxle life by reduc- ing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress.
Page 148 148 STARTING AND OPERATING for automatic transaxle vehicles, or reverse for vehicles with manual transaxle. To release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transaxle locking mechanism may make it...
Page 149: Brake System
BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 150: Power Steering
150 STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 151 Traction Control Switch A push-button located on the top of the steering column turns the Traction Control System ON or OFF. The system is always in the “ON” mode unless: • The traction control switch has been used to turn the system off;...
Page 152: Tire Safety Information
152 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 153 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 154: Tire Identification Number (Tin)
154 STARTING AND OPERATING H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 155 DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards, and is approved for highway use. MA = Code representing the tire manufacturing location. (2 digits) L9 = Code representing the tire size. (2 digits) ABCD = Code used by tire manufacturer.
Page 156: Tire Loading And Tire Pressure
156 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
Page 157 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 158 158 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and...
Page 159 STARTING AND OPERATING 159...
Page 160: Tires-General Information
160 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 161: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 162 162 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”.
Page 163: Radial-Ply Tires
WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 164: Limited Use Spare - If Equipped
164 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
Page 165: Tread Wear Indicators
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 166: Life Of Tire
166 STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread.
Page 167: Alignment And Balance
WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Page 168: Tire Chains
168 STARTING AND OPERATING TIRE CHAINS Due to limited clearance, tire chains are not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during winter.
Page 169: Autostick - If Equipped
Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected before rotating. The suggested rotation method is the “forward-cross”...
Page 170: Autostick Operation
170 STARTING AND OPERATING Autostick Operation The Autostick position is just below the Overdrive posi- tion and is identified by the word “AUTOSTICK”. When you place the shift lever in the Autostick position, it can be moved from side to side. Moving the lever to the left (-) triggers a downshift and to the right (+) an upshift.
Page 171: Fuel Requirements
• The transaxle will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions. • While in the Autostick mode, Speed Control will only function in third or fourth gear. Downshifting out of third gear turns off speed control.
Page 172: Reformulated Gasoline
172 STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
Page 173: Mmt In Gasoline
MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles.
Page 174: Carbon Monoxide Warnings
174 STARTING AND OPERATING malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers are not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not the responsibility of the manufacturer.
Page 175: Flexible Fuel- (Fleet Vehicles Only)
FLEXIBLE FUEL— (Fleet Vehicles Only) E-85 General Information The information in this section is for Flexible Fuel ve- hicles only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Un- leaded Gasoline Only. This section only covers those subjects that are unique to these vehicles.
Page 176: Selection Of Engine Oil For Flexible Fuel
176 STARTING AND OPERATING Observing these precautions will avoid possible hard starting and/or significant deterioration in drivability during warm up. NOTE: When the ambient temperature is above 90°F, you may experience hard starting and rough idle follow- ing start up even if the above recommendations are followed.
Page 177: Adding Fuel
CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the driver’s side of the vehicle.
Page 178: Vehicle Loading
178 STARTING AND OPERATING CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Lamp to turn on. WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled.
Page 179 Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR. Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its...
Page 180: Trailer Hitch Classification
180 STARTING AND OPERATING Trailer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
Page 181: Trailer Towing Weights (Maximum Trailer Weight Ratings)
Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area 2.4L Automatic/ 20 Sq. Ft Manual 2.7L Automatic/ 20 Sq. Ft. Manual Refer to local laws for maximum trailer towing speeds. Note 1 –...
Page 182: Towing Requirements
182 STARTING AND OPERATING Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle.
Page 183 Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings. WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel.
Page 184 184 STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires −...
Page 185 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines.
Page 186: Towing Tips
186 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
Page 187 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend transmission life by reducing exces- sive shifting and heat build up.
Page 189: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....190 If Your Engine Overheats ....190 Jacking And Tire Changing .
Page 190: Hazard Warning Flasher
190 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash.
Page 191: Jacking And Tire Changing
CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle in Park with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service.
Page 192: Preparations For Jacking
192 WHAT TO DO IN EMERGENCIES Preparations for Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, and set the parking brake. Place the gear selector in PARK. • Turn on the Hazard Warning Flasher, park vehicle on firm, level surface.
Page 193 WHAT TO DO IN EMERGENCIES 193 1. Block wheel diagonally op- posite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage.
Page 194 194 WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground.
Page 195 WHAT TO DO IN EMERGENCIES 195 Jack Engagement Locations...
Page 196 196 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove lug nuts and tire. 7.
Page 197: Jump-Starting Procedures If Battery Is Low
JUMP-STARTING PROCEDURES IF BATTERY IS WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 198 198 WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. Jump Starting 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attach- ment of the vehicle with the discharged battery.
Page 199 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion;...
Page 200: Driving On Slippery Surfaces
200 WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines.
Page 201: Freeing A Stuck Vehicle
FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
Page 202: Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground)
202 WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h).
Page 203: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine ......205 2.7L Engine ......206 Onboard Diagnostic System —...
Page 204 204 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion ......233 Fuses ....... 237 Underhood Fuses (Power Distribution Center) .
Page 205: 2.4L Engine
MAINTAINING YOUR VEHICLE 205 2.4L ENGINE 2.4L Engine Compartment...
Page 206: L Engine
206 MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.7L Engine Compartment...
Page 207: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 208: Emissions Inspection And Maintenance Programs
208 MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running,...
Page 209: Replacement Parts
If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update.
Page 210: Maintenance Procedures
210 MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 211 Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you.
Page 212 212 MAINTAINING YOUR VEHICLE If none of these apply to you, then change your engine oil at every interval shown on schedule A of the Mainte- nance Schedules section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first.
Page 213 Engine Oil Viscosity (SAE Grade) Engine Oil Fill Cap SAE 5W-20 and SAE 5W-30 engine oils are recom- mended for all operating temperatures. These engine oils are designed to improve low temperature starting and vehicle fuel economy. Refer to the engine oil filler cap for the preferred engine oil viscosity grade for each vehicle.
Page 214 214 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area.
Page 215 Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe con- ditions, the filter element should be inspected periodi- cally and replaced if necessary at the intervals shown on Schedule “B”.
Page 216: Crankcase Emission Control System
216 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Page 217 NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting. Battery Location To access the battery, turn the steering wheel fully to the right and remove the inner fender shield.
Page 218: Air Conditioner
218 MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
Page 219: Power Steering - Fluid Check
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 220: Suspension Ball Joints
220 MAINTAINING YOUR VEHICLE Fluid level should be maintained at the proper level indicated on the side of the reservoir. If necessary, add fluid to restore the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type.
Page 221: Windshield Wiper Blades
If you use a lubricant that cannot be dispensed directly into the lock cylinder, apply a small amount of the lubricant to the key. Insert the key into the lock cylinder, then proceed as described above, to distribute the lubri- cant within the lock cylinder.
Page 222: Windshield Washers
222 MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement • Lift the wiper arm away from the glass. • Push the release tab and slide the wiper blade assem- bly away from the wiper arm. Gently place the wiper arm on the windshield. •...
Page 223: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged;...
Page 224 224 MAINTAINING YOUR VEHICLE system should be drained, flushed and refilled with fresh coolant. Check the front of the radiator for any accumu- lation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
Page 225 replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Addi- tive Technology (HOAT) coolant. When adding coolant, a minimum solution of 50% rec- ommended Mopar Antifreeze/ Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technol- ogy), or equivalent, in water should be used.
Page 226 226 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine.
Page 227: Hoses And Vacuum/Vapor Harnesses
Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator.
Page 228: Brakes
228 MAINTAINING YOUR VEHICLE Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
Page 229 Insure nylon tubing in these areas has not melted or collapsed. NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling area is not neces- sarily an indication of leakage.
Page 230: Fuel System Hoses
230 MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that has a lower initial boiling point than MOPAR DOT 3 Brake Fluid or that is unidentified as to DOT FMVSS specification may result in sudden brake failure during hard or pro- longed braking.
Page 231 Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturers recommended transmis- sion fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
Page 232 232 MAINTAINING YOUR VEHICLE • If the fluid is hot (180°F / 82°C), the reading should be in the cross hatched area marked ”HOT” (between the upper two holes in the dipstick). • If the fluid level shows low, add sufficient transmis- sion fluid to bring to the proper level.
Page 233: Appearance Care And Protection From Corrosion
Frequency of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the lubricant has become contaminated with water. If con- taminated with water, the fluid should be changed im- mediately.
Page 234 234 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
Page 235 Never use cleaners that contain acid, oven cleaners or any abrasive metal cleaner as they will cause perma- nent staining and/or corrosion. • If you carry special cargo such as chemicals, fertilizers, deicer salt, etc., be sure that such materials are well packaged and sealed.
Page 236 236 MAINTAINING YOUR VEHICLE Leather is best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather surface and should be removed immediately with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean or equivalent.
Page 237: Fuses
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 238: Interior Fuses
238 MAINTAINING YOUR VEHICLE A Power Distribution Center is located in the engine compartment; near the air cleaner. This information ap- plies to vehicles built without the fuse and relay num- bering embossed on the Power Distribution Center Top Cover. Interior Fuses Fuse Panel Cover The fuse access panel is behind the end cover at the left...
Page 239 Cavity Fuse Circuit 10 Amp Red Heated Rear Window Indica- 20 Amp Yel- Instrument cluster illumina- tion, Park and tail Lights 20 Amp Yel- Power Receptacle, Horns, Ignition, Fuel, Start 15 Amp Blue Power Door Lock Motors (Body Control Module) 20 Amp Yel- Daytime Running Light Module (Canada)
Page 240: Vehicle Storage
240 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e.
Page 241: Bulb Replacement
BULB REPLACEMENT Headlight Bulb Replacement 1. Open the hood and remove the two headlight mount- ing screws. MAINTAINING YOUR VEHICLE 241 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool.
Page 242 242 MAINTAINING YOUR VEHICLE 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assem- bly away from the vehicle. 4.
Page 243: Park, Turn Signal, Sidemarker Bulb Replacement
6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 8. Reinstall the headlight assembly. Park, Turn Signal, Sidemarker Bulb Replacement 1.
Page 244: Fog Light Bulb Replacement
244 MAINTAINING YOUR VEHICLE Fog Light Bulb Replacement 1. Remove the screw securing the light assembly to the front fascia. 2. Pull the light assembly away from the vehicle to expose the bulb and socket assembly. 3. Disconnect the wiring connector from the bulb and socket assembly.
Page 245: Center Stoplight Bulb Replacement
Center Stoplight Bulb Replacement 1. Open the trunk. Turn the bulb socket counterclockwise to remove it from the housing. 2. Pull the bulb out of the socket, replace the bulb and reinstall the bulb and socket assembly. Rear Light Bulb Replacement 1.
Page 246: License Plate Bulb Replacement
246 MAINTAINING YOUR VEHICLE License Plate Bulb Replacement 1. Locate both small slots on the outboard side of the license lamp. Using a small screwdriver, remove the entire housing. 2. Turn the bulb socket counterclockwise to remove it from the housing. Pull the bulb out of the socket. Replace the bulb and snap it back into place on the housing of the chrome appliqué.
Page 247: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Engine Oil Use API Certified engine oil. SAE 5W-20 and SAE 5W-30 are recommended. Refer to the engine oil fill cap for the correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
Page 248: Chassis
248 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
Page 249 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..250 Maintenance Schedules ....250 Schedule “B” ......253 Schedule “A”...
Page 250: Emission Control System Maintenance
250 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 251 • Taxi, police, or delivery service (commercial ser- vice). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5,000 km) or 3 months, whichever comes first and follow schedule B of the “Maintenance Schedules”...
Page 252 252 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transaxle and add as needed. •...
Page 253: Schedule "B" 253
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an •...
Page 254 254 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
Page 255 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if re- quired.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 256 256 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
Page 257 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 258 258 SCHEDULE “B” Miles (Kilometers) Change the automatic transmission fluid and filter. Rotate the tires. Flush and replace engine coolant at 60 months, if not done at 100,000 miles. 57,000 60,000 63,000 66,000 (95 000) (100 000) (105 000) (110 000) (115 000) 69,000 72,000 (120 000)
Page 259 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 260 260 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on the 2.7 liter en- gine.
Page 261 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Inspect the air cleaner filter and replace if neces- sary.* Replace the air cleaner filter. Replace the spark plugs on the 2.4 liter engine. Replace the ignition cables on the 2.4 liter engine.
Page 262 262 SCHEDULE “B” Miles (Kilometers) Flush and replace engine coolant at 120 months, if not done at 100,000 miles. Rotate the tires. * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty.
Page 263: Schedule "A" 263
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes.
Page 264 264 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if re- quired.
Page 265 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter en- gine.
Page 266 266 SCHEDULE “A” Miles (Kilometers) [Months] Replace the accessory drive belts on 2.4L engine. Flush and replace the engine coolant, if not replaced at 60 months. Rotate the tires. 78,000 84,000 90,000 96,000 (130 000) (140 000) (150 000) (160 000) (170 000) (180 000) (190 000) [78] [84] [90]...
Page 267 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Check and replace, if necessary, the PCV valve.
Page 268 268 SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 269: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......270 Prepare For The Appointment .
Page 270: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 271 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: •...
Page 272: Warranty Information (U.s. Vehicles Only)
272 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.
Page 273: Reporting Safety Defects
REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 274 274 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts.
Page 275: Department Of Transportation Uniform Tire Quality Grades
DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
Page 276: Temperature Grades
276 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 277 INDEX...
Page 278 278 INDEX About Your Brakes ..... . 149 ABS (Anti-Lock Brake System) ... . . 149 Adding Engine Coolant (Antifreeze) .
Page 279 Shifting ......145 Special Additives ..... 232 Autostick .
Page 280 280 INDEX Changing A Flat Tire ....191 Charging System Light ....84 Chart, Tire Sizing .
Page 281 Daytime Running Lights ....62 Dealer Service ......209 Defroster, Rear Window .
Page 282 282 INDEX Oil Synthetic ......213 Overheating ......190 Timing Belt .
Page 283 Filler Cap (Gas Cap) ....177 Filter ......215 Gasoline .
Page 284 284 INDEX HomeLink (Garage Door Opener) Transmitter . 69 Hood Prop ......58 Hood Release .
Page 285 Dimmer Switch, Headlight ... . . 61,63 Engine Temperature Warning ... . . 86 Exterior Check ......46 Fog .
Page 286 286 INDEX Schedule “A” ......263 Schedule “B” ......253 Malfunction Indicator Light (Check Engine) .
Page 287 Passing Light ......63 Pets ........44 Placard, Tire and Loading Information .
Page 288 288 INDEX Safety Checks Outside Vehicle ....46 Safety Defects, Reporting ....273 Safety Information, Tire .
Page 289 Starting ......140 Cold Weather ......141 Engine Fails to Start .
Page 290 290 INDEX Sizes ....... 153 Snow Tires ......168 Spinning .
Page 291 Vanity Mirrors ......54 Vehicle Identification Number (VIN) ..6 Vehicle Loading .
Page 292 292 INDEX...
Page 293 NOTES...
Page 294 NOTES...
Page 295 NOTES...
Page 296 NOTES...

This manual is also suitable for:

Stratus 2006 Stratus sedan 2006

Dodge 2006 JR41 Stratus Sedan Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2006 JR41 Stratus Sedan

Summary of Contents for Dodge 2006 JR41 Stratus Sedan