Dodge 2005 Dakota Owner's Manual

Dodge 2005 Dakota Owner's Manual

Dodge 2005 dakota automobile owner's manual
Table of Contents

Advertisement

SECTION
1

INTRODUCTION

2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
4
INSTRUMENT PANEL AND CONTROLS
5
STARTING AND OPERATING
6
WHAT TO DO IN EMERGENCIES
7
MAINTAINING YOUR VEHICLE
8
MAINTENANCE SCHEDULES
9
IF YOU NEED CONSUMER ASSISTANCE
10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
INDEX
TABLE OF CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
PAGE
1
2
3
4
5
6
7
8
9
10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2005 Dakota and is the answer not in the manual?

Questions and answers

Josie
March 13, 2025

Anti theft system unlock

1 comments:
Mr. Anderson
March 13, 2025

To unlock the anti-theft system on a 2005 Dodge Dakota, follow these steps:

1. Insert a programmed Sentry Key fully into the ignition.
2. Turn the key to the "ON" position.
3. Wait for the Security Light to stop flashing and stay on for 3 seconds, then turn off.
4. If the vehicle does not start, try another programmed key.
5. If the system remains locked, you may need to program a new key or seek assistance from a dealer.

If additional keys need to be programmed, follow the key programming procedure in the manual.

This answer is automatically generated

Summary of Contents for Dodge 2005 Dakota

  • Page 1: Introduction

    TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
  • Page 3: Table Of Contents

    CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
  • Page 4: Introduction

    4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
  • Page 5: Warnings And Cautions

    This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
  • Page 6: Vehicle Modifications / Alterations

    6 INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
  • Page 7 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....10 Key-In-Ignition Reminder ....10 Sentry Key —...
  • Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement ....26 Security Alarm System — If Equipped ..27 To Set The Alarm .
  • Page 9: Safety Checks You Should Make Outside The

    Safety Tips ......73 Exhaust System ..... . .73 Safety Checks You Should Make Inside The Vehicle .
  • Page 10: Things To Know Before Starting Your Vehicle 7

    10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front.
  • Page 11: Sentry Key - If Equipped

    SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal, the vehicle will start and run for 2 seconds, then shut off.
  • Page 12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Security Light will illuminate for about 3 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Light will flash continuously to signal that the vehicle has been immobi- lized.
  • Page 13: Ignition And Steering Lock

    2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds, a chime will sound and the Security Light will begin to flash. Turn the ignition back to the OFF position and remove the second key.
  • Page 14: Automatic Transmissions

    14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE depress and hold the release button located between the ignition switch and the instrument panel. Turn the igni- tion key to LOCK and remove the key. Manual Transmissions Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your ve- hicle.
  • Page 15: Illuminated Entry

    Automatic Transmissions NOTE: On vehicles equipped with an automatic trans- mission, the key cannot be turned to LOCK until the selector is in the PARK position. Do not attempt to pull the shift lever out of PARK after the key is in the LOCK position.
  • Page 16: Door Locks

    16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks All the doors can be “manually” locked from the inside by pushing down the door lock plunger, located at the rear of the door. Both front doors may be opened from the inside with the door lock plunger in the down or locked position.
  • Page 17: Power Door Locks

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Power Door Locks Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
  • Page 18 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a safety feature the doors will not lock when using the door lock switches during the following conditions: • The driver’s door is open while the key is in the ignition. Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph...
  • Page 19 • The doors of the vehicle must be locked automatically by the Automatic Door Lock feature. • The vehicle is in P (Park) and the ignition switch is in any key position. This feature will not operate if any of the conditions above are not met or following has occurred: •...
  • Page 20: Child Protection Door Lock

    20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
  • Page 21: Remote Keyless Entry

    WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
  • Page 22: To Unlock The Doors

    22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors.
  • Page 23 Horn Chirp Programming The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure: 1. Press and hold the LOCK button on the key fob. 2. After holding the LOCK button for four seconds, also press the PANIC button within 6 seconds.
  • Page 24: Using The Panic Alarm

    24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
  • Page 25: Programming Additional Transmitters

    1. Weak batteries in transmitter. The expected life of batteries is five years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios. Programming Additional Transmitters Vehicles will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle.
  • Page 26: Battery Replacement

    26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. Using the fob to be programmed, press and release both the LOCK and UNLOCK buttons, simultaneously for 2 seconds and then release. 9. Press and release the UNLOCK button a single chime will be heard.
  • Page 27: Security Alarm System - If Equipped

    2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together.
  • Page 28: To Disarm The System

    28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter to unlock the doors. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.
  • Page 29: Windows

    WINDOWS Power Windows THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 The control on the left front door has up-down switches that give you finger tip control of all four power win- dows. There is a single opening and closing switch on the passenger doors for passenger window control.
  • Page 30: Auto Down

    30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF.
  • Page 31: Sliding Rear Window

    Sliding Rear Window Sliding Window Light Latch A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the...
  • Page 32: Lap/Shoulder Belts

    32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up.
  • Page 33 WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
  • Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
  • Page 35 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increas- ing the possibility of injury.
  • Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
  • Page 37: Adjustable Upper Shoulder Belt Anchorage

    Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best.
  • Page 38: Automatic Locking Mode (If Equipped)

    38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode (if equipped) To convert from the normal emergency locking mode to the automatic locking mode, grasp the shoulder belt portion and pull all of the webbing out of the retractor. Allow some of the webbing to retract into the retractor, as the belt retracts you will hear a clicking sound to indicate the seat belt is now in the automatic locking mode.
  • Page 39: Enhanced Driver Seat Belt Reminder System (Beltalert)

    The pretensioners are triggered by the Occupant Re- straint Controller (ORC). Like the airbags, the pretension- ers are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced. Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is...
  • Page 40: Seat Belts And Pregnant Women

    40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming.
  • Page 41: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbags

    WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
  • Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
  • Page 43 Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
  • Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. 4.
  • Page 45 Air Bag System Components The airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors (If Equipped) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Window Bags above Side Windows (If Equipped) •...
  • Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters.
  • Page 47 NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned off.
  • Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all properly installed rear facing child re- straints, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. If the PAD indicator light is not illuminated, DO NOT assume the air bag is turned off and move the child restraint to the second row of seats (if equipped).
  • Page 49 the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS.
  • Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Indicator Light and the Airbag Warning Light. Once the lodged object is removed, the fault will be automatically cleared after a short period of time. • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
  • Page 51 or a weight less than the predetermined threshold, the ORC will not illuminate the PAD indicator light even though the airbag is turned OFF. • Your vehicle has four Weight Sensors located within the seat structure or between the seat tracks and cushion frame.
  • Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle.
  • Page 53 NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: •...
  • Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
  • Page 55: Passenger Airbag On/Off Switch - If Equipped

    • The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control mod- ule may also be disabled.
  • Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death.
  • Page 57: Event Data Recorder (Edr)

    To Shut Off the Passenger Frontal Airbag Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove the key from the switch. This will shut off the passenger frontal airbag. The passenger frontal airbag symbol and the word “OFF”...
  • Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the event that an investigation is undertaken by DaimlerChrysler Corporation (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
  • Page 59: Child Restraint

    • Airbag deployment level (if applicable) • Seatbelt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Cruise control status • Traction/stability control status Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too.
  • Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg). Convertible child seats can be used either rearward-facing or forward-facing in the vehicle.
  • Page 61 Children Too Large for Booster Seats • Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
  • Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
  • Page 63 provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH- compatible child restraint systems are now available. However, because the lower anchorages are to be intro- duced over a period of years, child restraint systems having attachments for those anchorages will continue to...
  • Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCH compatible, you can only install the child restraints using the vehicle’s seat belts.
  • Page 65 of the seat cushion where it meets the seat back, and are just visible when you lean into the vehicle to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
  • Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using the Vehicle Seat Belt The passenger seat belts are equipped with either cinch- ing latch plates or automatic locking retractors, which are designed to keep the lap portion tight around the child restraint so that it should not be necessary to use a locking clip.
  • Page 67 Child Restraint Tether Anchor The Club Cab model has two routing straps located behind each of the rear outboard seat- ing positions. The tether anchor itself is located in the center of vehicle, in between the two seating positions. The front outboard passenger seating position is also equipped with a child tether anchorage, located at the base of the front seat back.
  • Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Strap at the Front Passenger Seat (Club Cab) 1. Route the child restraint tether strap up and over the front passenger seat back and under the head restraint. 2. Connect the tether strap to the lower anchor. 3.
  • Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Tether Straps at the Rear Passenger Seat (Club Cab) 1. Route the child restraint tether strap through the routing loop, located directly behind the child restraint. The routing loops are located behind the flip-down door on the cab back panel (padded bolster).
  • Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Straps at the Rear Passenger Seat (Quad Cab) 1. Route the child restraint tether strap under the head restraint for the outboard seating positions, and then through the anchor strap outer loop (webbing material loop), located directly behind the child restraint.
  • Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Multiple Child Restraint Quad Cab...
  • Page 72: Engine Break-In Recommendations

    72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
  • Page 73: Safety Tips

    A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an ex- tremely toxic gas that by itself is colorless and odorless.
  • Page 74: Safety Checks You Should Make Inside The Vehicle

    74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.).
  • Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Fluid Leaks Check the area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if gasoline fumes are detected, the cause should be located and corrected.
  • Page 77: Understanding The Features Of Your Vehicle

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......81 Inside Day/Night Mirror ....81 Automatic Dimming Mirror —...
  • Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment — If Equipped ......109 Adjustable Head Restraints —...
  • Page 79 To Set At A Desired Speed ....123 To Deactivate ......123 To Resume Speed .
  • Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Erasing Homelink Buttons ....138 Reprogramming a Single Homelink Button . . . 138 Security ......139 Electrical Power Outlets .
  • Page 81: Mirrors

    MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck).
  • Page 82: Understanding The Features Of Your Vehicle

    82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for annoying head- light glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror.
  • Page 83: Electric Remote-Control Mirrors

    Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move.
  • Page 84: Heated Mirrors - If Equipped

    84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object.
  • Page 85 The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32 name phonebook accessible only in that language. This system is driven through your Blue- tooth™ Hands-Free profile cellular phone. UConnect™ features Bluetooth™...
  • Page 86: Operation

    86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details. The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped.
  • Page 87 NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin.
  • Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Setup Phone Pairing. • When prompted, after the voice on beep, say Pair a Phone. • You will be asked to say a four-digit pin number which you will later need to enter into your cellular.
  • Page 89 Dial by Saying a Number • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Dial. • System will prompt you to say the number you want call. • For example, you can say 234-567-8901. The phone number that you enter must be of valid length and combination.
  • Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the Ready prompt and the following beep, say Phonebook New Entry.
  • Page 91 • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing.
  • Page 92: Phone Call Features

    92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After confirmation, the phonebook entries will be de- leted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. •...
  • Page 93 Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call.
  • Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched.
  • Page 95: Uconnect™ System Features

    Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehicle can be any one of three types: • After ignition key is switched off, a call can continue on the UConnect™...
  • Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: •...
  • Page 97 Please refer to the 24-Hour Towing Assistance coverage details in the DaimlerChrysler Corporation 24-Hour Towing Assistance Program Guide. Paging To learn how to page, refer to section Working with Automated Systems. Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™...
  • Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing Would you like to pair a phone, clear a , you could press the ’Voice Recognition’...
  • Page 99: Advanced Phone Connectivity

    may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you.
  • Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names •...
  • Page 101: Things You Should Know About Your Uconnect™ System

    • The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle. Delete UConnect™...
  • Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English and Spanish accents, the system may not always work for some. •...
  • Page 103 • Performance, such as, audio clarity, echo. and loud- ness to a large degree, rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Cellular phones have been found to occasionally loose connection to the UConnect™...
  • Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
  • Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105...
  • Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
  • Page 107: Seats

    North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
  • Page 108: Front Seats Manual Seat Recliners

    108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
  • Page 109: Manual Lumbar Support Adjustment - If Equipped

    WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
  • Page 110: Way Power Seat Adjuster - Driver's Side Only

    110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, depress the release button located at the base of the head restraint and push down on the head restraint. 6 - Way Power Seat Adjuster — Driver’s Side Only The 6-way power seat adjuster switches are on the outboard side of the driver’s seat.
  • Page 111 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the driver’s seat cushion. Three switches control the seat movement. The four-way switch in the center can be moved forward or backwards to get the most comfortable position.
  • Page 112: Club Cab/Quad Cab Rear Seat

    112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Club Cab/Quad Cab Rear Seat More cargo space is available by lifting up on the rear seat cushion. The Quad Cab rear seat is a 60/40 split cushion and full back. Either cushion can be raised independently. Heated Seats —...
  • Page 113 Then push the safety latch lever down while lifting the grille with your right hand. It is located at the top center of the grille just left of center. Lift the hood and gas filled props will hold it open. Secondary Latch Location (Push Down) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 To prevent possible damage, do not slam the hood to...
  • Page 114: Lights

    114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.When a door is open and the interior lights are on, rotating the dimmer...
  • Page 115: Battery Saver

    control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the Party mode because it allows the doors to stay open for extended periods of time without discharging the vehi- cle’s battery.
  • Page 116: Headlamp Delay

    116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp Delay To aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 60 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off.
  • Page 117: Daytime Running Lights (Canada Only)

    To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
  • Page 118: Cargo Light - If Equipped

    118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO Light — If Equipped The cargo lights are turned on by pressing on the CARGO button. The interior lights will also turn on when the cargo lights are on. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
  • Page 119: Passing Light

    The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective.
  • Page 120: Windshield Wipers

    120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
  • Page 121: Windshield Washers

    WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
  • Page 122: Tilt Steering Column

    122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. WARNING! Tilting the steering column while the vehicle is moving is dangerous.
  • Page 123: Electronic Speed Control - If Equipped

    ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator opera- tion at speeds greater than (refer to the table below for the speed for your specific engine). The controls are mounted on the steering wheel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 To Activate Push the ON/OFF button to the ON position.
  • Page 124: To Resume Speed

    124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Speed Control ON when not in use is dangerous. You could accidentally set the system to cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.
  • Page 125: To Accelerate For Passing

    Functions 3.7L Engage Speed 30 mph (48 km/h) Minimun RESUME Speed 25 mph (40 km/h) ACCEL Increase 2 mph (3km/h) DECEL Decrease 1 mph (2 km/h) Dropout Speed 25 mph (40 km/h) To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed.
  • Page 126: Overhead Console

    126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
  • Page 127: Courtesy/Reading Lights

    Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped.
  • Page 128: Reset Button

    128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RESET Button Use this button to reset the following displays to zero: • Average Fuel Economy • Trip Odometer • Elapsed time. Global Reset If the RESET button and STEP button are pressed at the same time and held for 3 seconds the Global Reset feature will reset the distance to empty (using a default fuel economy value), fuel economy, trip odometer, and...
  • Page 129: Step Button

    Step Button Use this button to choose or cycle through the four trip conditions. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases.
  • Page 130: Trip Odometer (Odo)

    130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When Distance To Empty = 0, the fuel gauge pointer will initially be on the red “E” marker. At this point (fuel gauge pointer on the the red “E” marker) there is reserve fuel capacity, which corresponds to approximately 8% of tank volume.
  • Page 131: Compass/Temperature Display

    Compass/Temperature Display WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
  • Page 132: To Put Into A Calibration Mode

    132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Put Into a Calibration Mode Turn on the ignition and set the display to “Compass/ Temperature.” Press and hold the RESET button to change the display between VAR (compass variance) and CAL (compass calibration) modes. When the CAL sym- bol is displayed complete one 360 degree turn in an area free from large metal objects or power lines.
  • Page 133: Outside Temperature

    To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
  • Page 134: Programming Homelink

    134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
  • Page 135 WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
  • Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the Gate Operator/Canadian Pro- gramming section. 4. The HomeLink indicator light will flash slowly and then rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter.
  • Page 137: Canadian Programming/Gate Programming

    and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device. NOTE: To program the remaining two HomeLink but- tons, begin with Programming step two.
  • Page 138: Using Homelink

    138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.).
  • Page 139: Security

    Security Garage Door Opener Operation with Security Alarm (if equipped) If your vehicle is equipped with the Security Alarm feature, the operation of the HomeLink feature will be purposely inhibited if the Security Alarm is Armed . This prevents HomeLink operation due to un-authorized vehicle entry.
  • Page 140: Electrical Outlet Use With Engine Off (Battery Fed Configuration)

    140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE automatically when ready for use. To preserve the heat- ing element, do not hold the lighter in the heating position. The console outlet can be reconfigured by the customer to operate only when the ignition is On (switch battery fed) or with the ignition switch On/Off (battery fed) to allow for cellular phone charging and/or operation while the ignition is Off.
  • Page 141: Floor Console - If Equipped

    FLOOR CONSOLE — IF EQUIPPED Floor Console Features Floor Console Features The Floor Console between the driver’s and front pas- senger’s seat, has the following features: • Miscellaneous storage compartments • Flexible cup holder inserts • Portable phone storage bin •...
  • Page 142: Center Storage Compartment - If Equipped

    142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outlet and Portable Phone Storage The console is equipped with a power outlet, portable phone storage bin, and phone cord routing. The phone storage bin can be used when ease access to the phone is needed.
  • Page 143: Cup Holders

    CUP HOLDERS If your vehicle has bucket seats with a center console, there are three cup holders located on the console. Refer to the section on floor console. A two-cavity cup holder is available on all Quad Cab with rear seats mounted on the floor. Front Cup Holders –...
  • Page 144: Slide-In Campers

    144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Unclip and remove the cables from the box while maintaining a 45° angle. 3. Lift the tailgate off of the pivot on the passenger side by pulling upward and rearward at the same time. 4.
  • Page 145: General Information

    General Information The Manufacturer’s Warranty does not apply to body modifications and special equipment, such as a camper unit, heaters, stoves, refrigerators, etc., supplied by manufacturers other than the manufacturer. For warranty coverage and service on these items, contact the appli- cable manufacturer.
  • Page 147: Instrument Panel And Controls

    INSTRUMENT PANEL AND CONTROLS CONTENTS Instruments And Controls ....150 Instrument Cluster ..... . 151 Instrument Cluster Description .
  • Page 148 148 INSTRUMENT PANEL AND CONTROLS Sales Code RAQ – AM/FM/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Video Capabilities ... . . 166 Operating Instructions - Radio Mode ..166 Operation Instructions - (CD Mode For CD Audio Play) .
  • Page 149 Remote Sound System Controls — If Equipped . . 182 Radio Operation ..... . 183 CD Player ......183 Compact Disc Maintenance .
  • Page 150: Instruments And Controls

    150 INSTRUMENT PANEL AND CONTROLS INSTRUMENTS AND CONTROLS...
  • Page 151: Instrument Cluster

    INSTRUMENT PANEL AND CONTROLS 151 INSTRUMENT CLUSTER...
  • Page 152: Instrument Cluster Description

    152 INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. (See page 245 for more information.) 2. Temperature Gage The temperature gage indicates engine coolant temperature.
  • Page 153 left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. (See page 118 for more information.) 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less.
  • Page 154 154 INSTRUMENT PANEL AND CONTROLS CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off.
  • Page 155 12. ABS Warning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for approximately 3 seconds. If this light remains on or comes on during driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
  • Page 156 156 INSTRUMENT PANEL AND CONTROLS U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined.
  • Page 157 21. BRAKE System Warning Light This light will light when the ignition key is turned to the ON position and will remain on for a few seconds. If the light stays on, it may be an indication that the parking brake has not been released, or there is a low brake fluid level.
  • Page 158 158 INSTRUMENT PANEL AND CONTROLS If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service. Although your vehicle will usually be drivable and not need towing, see your dealer for service as soon as possible.
  • Page 159: Radio Reception Information

    29. Cargo Lamp The Cargo Lamp light will illuminate when the Cargo Lamp is activated from the headlight control switch, located below the headlight switch. 30. TOW/HAUL The TOW/HAUL button is located at the end of the gear shift lever. This light will illuminate when the TOW/ HAUL button has been selected.
  • Page 160: Electronic Digital Clock

    160 INSTRUMENT PANEL AND CONTROLS ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the “ON” or “ACC”...
  • Page 161: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Hands Free Phone Capability

    SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL HANDS FREE PHONE CAPABILITY INSTRUMENT PANEL AND CONTROLS 161 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
  • Page 162 162 INSTRUMENT PANEL AND CONTROLS Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player or Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
  • Page 163 RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satel- lite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency.
  • Page 164: Operation Instructions - Cd Mode

    164 INSTRUMENT PANEL AND CONTROLS Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be stored into push-button memory.
  • Page 165 NOTE: • You may insert or eject a disc with the radio or ignition switch OFF. • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day. SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD.
  • Page 166: Operating Instructions - Hands Free Phone - If Equipped

    166 INSTRUMENT PANEL AND CONTROLS Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
  • Page 167 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
  • Page 168 168 INSTRUMENT PANEL AND CONTROLS SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
  • Page 169 Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
  • Page 170: Operation Instructions - (Cd Mode For Cd Audio Play)

    170 INSTRUMENT PANEL AND CONTROLS 16 Digit-Character Program Type Jazz Classical Rhythm and Blues Rhythm_and_Blues Soft Rhythm and Blues Foreign Language Foreign_Language Religious Music Religious Talk Personality Public College Unassigned Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
  • Page 171 Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
  • Page 172: Load/Eject Button (Cd Mode For Cd Audio Play)

    172 INSTRUMENT PANEL AND CONTROLS SCAN Button (CD MODE For CD Audio Play) Press the Scan button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode For CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD is being loaded.
  • Page 173 TIME Button (CD MODE For CD Audio Play) Press this button to change the display from a large CD playing time display and small clock time display to a large clock time display and small CD playing time display. RW/FF (CD MODE For CD Audio Play) Press FF (Fast Forward) once and the CD player will begin to fast forward until FF is pressed again or RW or another CD button is pressed.
  • Page 174: Notes On Playing Mp3 Files

    174 INSTRUMENT PANEL AND CONTROLS Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported media (disc types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
  • Page 175 Supported MP3 file formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
  • Page 176: Operation Instructions

    176 INSTRUMENT PANEL AND CONTROLS Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
  • Page 177 LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
  • Page 178: Satellite Radio - If Equipped

    178 INSTRUMENT PANEL AND CONTROLS AM/FM Button (CD Mode For MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode For MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode For MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
  • Page 179: System Activation

    System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2.
  • Page 180: Selecting Satellite Mode In Ref Radios

    180 INSTRUMENT PANEL AND CONTROLS mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in REF Radios Press the MODE button repeatedly until S A appears in the display.
  • Page 181: Storing And Selecting Pre-Set Channels

    Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio.
  • Page 182: Reception Quality

    182 INSTRUMENT PANEL AND CONTROLS Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. •...
  • Page 183: Radio Operation

    The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
  • Page 184: Radio Operation And Cellular Phones

    184 INSTRUMENT PANEL AND CONTROLS 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
  • Page 185: Air Conditioning And Heater

    Air Conditioning And Heater Air Conditioning And Heater Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the outlets selected by the mode control.
  • Page 186 186 INSTRUMENT PANEL AND CONTROLS Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains dust, odors, high humidity, or if rapid cooling is desired. This feature allows for recir- culation of interior air only. Air flows through the panel outlets in this mode.
  • Page 187 Temperature Control The rotary knob at the center of the control panel controls the temperature of the inte- rior air. You can choose your degree of comfort by rotating the knob. The coldest tem- perature setting is to the ex- treme left (blue region) and the warmest setting is to the extreme right (red region) of...
  • Page 188: Operating Tips

    188 INSTRUMENT PANEL AND CONTROLS Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
  • Page 189 Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50% concentration of engine coolant to distilled water is recommended.
  • Page 190: Operation Tips Chart

    190 INSTRUMENT PANEL AND CONTROLS Operation Tips Chart...
  • Page 191: Rear Window Defroster - If Equipped

    INSTRUMENT PANEL AND CONTROLS 191 REAR WINDOW DEFROSTER – IF EQUIPPED CAUTION! Use care when washing the inside of the rear win- dow to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements.
  • Page 193: Starting And Operating

    STARTING AND OPERATING CONTENTS Starting Procedures ..... 196 Manual Transmission ....196 Automatic Transmission .
  • Page 194 194 STARTING AND OPERATING Brake System ......221 Rear Wheel Anti-Lock Brake System — (If Equipped) ....221 Four-Wheel Anti-Lock Brake System —...
  • Page 195 Snowplow ......263 Dodge Dakota Models ....263 Recreational Towing (Behind Motorhome, Etc.) .
  • Page 196: Starting Procedures

    196 STARTING AND OPERATING STARTING PROCEDURES The starter should not be operated for more than 15 second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Manual Transmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress clutch pedal to the floor before starting the vehicle.
  • Page 197: Normal Starting

    Normal Starting Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
  • Page 198: Engine Block Heater - If Equipped

    198 STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. After Starting The idle speed is automatically controlled on fuel injected engines and will decrease as the engine warms up.
  • Page 199: Automatic Transmission

    WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION Automatic Transmission The electronic PRNDL on the instrument cluster indicates the transmission gear selected. The selector lever is mounted on the right side of the steering column. To drive, move the selector lever from Park or Neutral to the desired drive position.
  • Page 200 200 STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without first pulling the lever toward you, after you have set it in P (Park).
  • Page 201 “N” Neutral Shift to Neutral when vehicle is standing for prolonged periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive For most city and highway driving. “2”...
  • Page 202 202 STARTING AND OPERATING • transmission has reached normal operating tempera- ture. NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level.
  • Page 203 performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to 3rd gear (for improved braking) will occur during steady braking.
  • Page 204 204 STARTING AND OPERATING transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission. This condition is normal and will not cause damage to the transmission. The torque converter will refill within five seconds of shifting from Park into any other gear position.
  • Page 205 Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the clutch pedal partially engaged, as this will cause abnormal wear on the clutch. Recommended Shift Speeds To use your manual transmission for fuel economy it should be upshifted as listed below.
  • Page 206: Four-Wheel Drive Operation

    206 STARTING AND OPERATING Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed.
  • Page 207 position - see Shifting Procedure section for specific shifting instructions. The 4HI and 4LO positions are designed for loose, slippery road surfaces only. Driving in the 4HI and 4LO positions on dry hard surfaced roads may cause increased tire wear and damage to the driv- eline components.
  • Page 208 208 STARTING AND OPERATING or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required. WARNING! Always engage the parking brake when powering down the vehicle if the SVC 4WD light is illumi- nated.
  • Page 209 WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
  • Page 210: Shifting Procedure - Nv233 Transfer Case

    210 STARTING AND OPERATING Shifting Procedure - NV233 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
  • Page 211 ON. At this time, reduce speed and stop spinning the wheels to complete the shift. There may be a delay up to 10 seconds for the shift to complete after the wheels have stopped spinning. 4HI to 4LO or 4LO to 4HI NOTE: When shifting into or out of 4LO some gear noise may be heard.
  • Page 212: Nv244 Transfer Case Operating Information / Precautions

    212 STARTING AND OPERATING NOTE: If steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process then the indicator light will flash and the current transfer case position will be maintained.
  • Page 213 When additional traction is required, the 4HI and 4LO positions can be used to lock the front and rear drive- shafts together through the transfer case inter-axle differ- ential and force the front and rear wheels to rotate at the same speed.
  • Page 214 214 STARTING AND OPERATING The SERVICE 4WD warning light monitors the electric shift 4WD system. If this light remains on after engine start up or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required.
  • Page 215 WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
  • Page 216: Shifting Procedure - Nv244 Transfer Case

    216 STARTING AND OPERATING Shifting Procedure - NV244 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
  • Page 217 spinning the wheels to complete the shift. There may be a delay up to 10 seconds for the shift to complete after the wheels have stopped spinning. NOTE: Delayed shifting out of the 4HI position may be experienced due to uneven tire wear, low tire pressure, or excessive loading.
  • Page 218: Limited-Slip Rear Axle Differential- If Equipped

    218 STARTING AND OPERATING 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). NOTE: If steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process, then the desired position indicator light will flash continuously while the original position indicator...
  • Page 219: Parking Brake

    Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface. This could cause both rear wheels to spin, and allow the vehicle to slide sideways on the crowned surface of a road or in a turn.
  • Page 220 220 STARTING AND OPERATING NOTE: The instrument cluster brake warning light indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
  • Page 221: Brake System

    BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly increased over that required with the power system operating. If either the front or rear hydraulic system loses normal capability, the remaining system will still function with some loss of braking effectiveness.
  • Page 222: Four-Wheel Anti-Lock Brake System - If Equipped

    222 STARTING AND OPERATING Four-Wheel Anti-Lock Brake System — If Equipped This Anti-Lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressure to prevent wheel lock-up and help avoid skidding on slippery surfaces.
  • Page 223: Power Steering

    WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
  • Page 224: Rocking The Vehicle

    224 STARTING AND OPERATING ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. The least amount of accelerator pedal pressure to main- tain the rocking motion without spinning the wheels or racing the engine is most effective.
  • Page 225 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
  • Page 226 226 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
  • Page 227 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
  • Page 228: Tire Identification Number (Tin)

    228 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
  • Page 229: Tire Loading And Tire Pressure

    STARTING AND OPERATING 229 Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the shutface of the driver’s door, the “B”...
  • Page 230 230 STARTING AND OPERATING Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
  • Page 231 combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard.
  • Page 232 232 STARTING AND OPERATING...
  • Page 233: Tires-General Information

    WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
  • Page 234: Tire Inflation Pressures

    234 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
  • Page 235 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
  • Page 236: Radial-Ply Tires

    236 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
  • Page 237: Compact Spare Tire - If Equipped

    Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
  • Page 238: Limited Use Spare - If Equipped

    238 STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly.
  • Page 239: Tread Wear Indicators

    WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
  • Page 240: Replacement Tires

    240 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators).
  • Page 241: Alignment And Balance

    CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
  • Page 242: Tire Chains

    242 STARTING AND OPERATING TIRE CHAINS Use “Class S” chains only on the rear tires on Dakota trucks, or other traction aids that meet SAE Type “S” specifications. NOTE: Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions:...
  • Page 243: Snow Tires

    These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Dakota trucks. NOTE: The use of class “S” chains is permitted on Dakotas with P245/70R16 tires. CAUTION! Do not use tire chains on 4x4 Dakota trucks equipped with P265/65R17 tires.
  • Page 244: Tire Rotation Recommendations

    244 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns.
  • Page 245: Fuel Requirements

    FUEL REQUIREMENTS All engines are designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high quality unleaded “regular” gaso- line having an octane rating of 87. The 3.7L/4.7L routine use of premium gasoline is not Engines recommended.
  • Page 246: Reformulated Gasoline

    246 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. We strongly support the use of reformulated gasolines.
  • Page 247: Materials Added To Fuel

    It is even more important to look for gasolines without MMT in Canada because MMT can be used at levels higher than allowed in the United States. MMT is pro- hibited in Federal and California reformulated gasolines. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives.
  • Page 248 248 STARTING AND OPERATING CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: Tighten the gas cap until you hear a “clicking” sound.
  • Page 249: Fuel System Cautions

    CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. WARNING! • Never allow any lit smoking materials near the vehicles while removing the cap or filling the tank.
  • Page 250: Carbon Monoxide Warnings

    250 STARTING AND OPERATING • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock. If spark knock persists, lighten the load, or engine piston damage may result.
  • Page 251: Catalytic Converter

    • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
  • Page 252: Vehicle Loading

    252 STARTING AND OPERATING A scorching odor may be detected if you continue to run a malfunctioning engine. The odor may indicate severe and abnormal catalyst overheating. If this occurs, the vehicle should be stopped, the engine shut off and the vehicle allowed to cool.
  • Page 253 Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the Month, Day, and Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN).
  • Page 254: Curb Weight

    254 STARTING AND OPERATING Inflation Pressure (Cold) This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
  • Page 255 WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle.
  • Page 256: Trailer Towing

    256 STARTING AND OPERATING TRAILER TOWING To maintain warranty coverage, follow the requirements and recommendations in this manual concerning ve- hicles used for trailer towing. Definitions The following trailer towing related terminology defini- tions will assist in understanding the subsequent sec- tions: GROSS COMBINATION WEIGHT RATING (GCWR) is the total permissible weight of your vehicle and trailer...
  • Page 257 Consider the following items when computing the weight on the rear axle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
  • Page 258: Trailer And Tongue Weight

    258 STARTING AND OPERATING • Do not interconnect the hydraulic brake system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs.
  • Page 259: Gross Combined Vehicle Weight Rating (Gcwr)

    Tongue Weight is the weight placed on the vehicle’s trailer hitch by the trailer. Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW on the tow hitch of your vehicle. Trailer sway control and equalizing hitch are required for tongue weights above 350 lbs.
  • Page 260: Trailer Towing Information (Maximum Trailer Weight Ratings)

    In Canada, refer to the following website address: http:// www.dodge.ca. Trailer Towing Requirements All Dodge Dakota trucks are intended to tow trailers up to 2,000 lbs. (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers over 2,000 lbs.
  • Page 261: Trailer Tow Wiring

    If you regularly pull a trailer, regardless of the trailer size, stop and turn signals on the trailer are recommended for motoring safety. When the additional trailer lighting is connected to the vehicle, the flasher does not provide an indication of outside lamp/bulb failure.
  • Page 262: Cooling System Tips-Trailer Towing

    262 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7 - Pin Connector Cooling System Tips—Trailer Towing To reduce potential for engine and transmission over- heating, take the following actions: •...
  • Page 263: Snowplow

    STARTING AND OPERATING 263 SNOWPLOW Dodge Dakota Models NOTE: Do not use Dodge Dakota Models for snowplow applications. WARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end of your vehicle.
  • Page 264: Recreational Towing (Behind Motorhome, Etc.)

    264 STARTING AND OPERATING CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)
  • Page 265: Recreational Towing 4Wd Models

    Recreational Towing 4WD Models CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the NV233 and NV244 HD transfer cases must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection button is located on the lower left hand corner of the 4WD Control Switch.
  • Page 266 266 STARTING AND OPERATING 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 4 seconds. 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8.
  • Page 267 CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P). Returning to Normal Operation Use the following procedure to prepare your vehicle for normal usage.
  • Page 268 268 STARTING AND OPERATING depressing the Neutral (N) button or are no longer met during the 1 second time, then all of the mode position indicator lights will flash continuously until all require- ments are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
  • Page 269: Traction

    CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road...
  • Page 271: What To Do In Emergencies

    WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....272 Adding Fuel ......273 Changing A Flat Tire .
  • Page 272: Hazard Warning Flasher

    272 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers.
  • Page 273: Adding Fuel

    ADDING FUEL If using a portable fuel container, it should have a flexible nozzle long enough to reach past the restriction in the fuel filler tube. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed.
  • Page 274: Changing A Flat Tire

    274 WHAT TO DO IN EMERGENCIES CHANGING A FLAT TIRE Jack Location In the Dakota, the scissor jack and tire changing tools for Club Cab models are stowed in a compartment under the rear passenger seat. Quad Cab model scissor jack and tire changing tools are accessed by lifting up the rear passen- ger seat.
  • Page 275 WHAT TO DO IN EMERGENCIES 275 Jack Stowage Location Club Cab Jack Stowage Location Quad Cab...
  • Page 276: Removing The Spare Tire

    276 WHAT TO DO IN EMERGENCIES WARNING! The jack is designed as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable supports are placed under the vehicle as a safety measure. The vehicle should be jacked on a firm level surface only.
  • Page 277 WHAT TO DO IN EMERGENCIES 277 • Rotate clockwise to stow the spare tire. Turning Lug Wrench and Extension Inserting Lug Wrench and Extension...
  • Page 278: Tire Changing Procedure

    278 WHAT TO DO IN EMERGENCIES It is recommended that you stow the flat or spare to avoid tangling the loose cable. Spare Tire Stowage Location NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
  • Page 279 Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in PARK (automatic transmission). On Four Wheel Drive vehicles, shift the transfer case to the “4L” position. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
  • Page 280 280 WHAT TO DO IN EMERGENCIES 3. When changing a front wheel, place the jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame (prior to inboard transition. Operate the jack using the jack drive tube and the wheel wrench - the tube exten- sion, may be used but is not required.
  • Page 281 Right Rear Jacking Location Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WHAT TO DO IN EMERGENCIES 281 WARNING! Raising the vehicle higher than necessary can make...
  • Page 282 282 WHAT TO DO IN EMERGENCIES 6. Using the wheel wrench, finish tightening the nuts in a crisscross pattern. Correct nut tightness is 85-115 ft. lbs. (115-155 N·m) torque. If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station.
  • Page 283: Jump Starting

    To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle.
  • Page 284 284 WHAT TO DO IN EMERGENCIES Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1.
  • Page 285 WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode.
  • Page 286: Emergency Tow Hooks - If Equipped

    286 WHAT TO DO IN EMERGENCIES EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks. WARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. WARNING! Stand clear of vehicles when pulling with tow hooks.
  • Page 287: Towing A Disabled Vehicle

    CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle.
  • Page 288 288 WHAT TO DO IN EMERGENCIES NOTE: Towing the vehicle at more than 30 mph (50 km/h) or for more than 15 miles (25 km) can cause severe transmission damage.
  • Page 289: Maintaining Your Vehicle

    MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment 3.7L V6 ....292 Engine Compartment 4.7L/4.7HO V-8 ..293 Onboard Diagnostic System — OBD II ..294 Loose Fuel Filler Cap Message .
  • Page 290 290 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 307 Power Steering — Fluid Check ... . 308 Front Suspension Ball Joints ....309 Drive Shaft Constant Velocity Joints .
  • Page 291 Center High-Mounted Stoplamp And Cargo Lamp ......338 License Lamps ..... . . 341 Fog Lamps .
  • Page 292: Maintaining Your Vehicle

    292 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.7L V6...
  • Page 293: Engine Compartment 4.7L/4.7Ho V-8

    MAINTAINING YOUR VEHICLE 293 ENGINE COMPARTMENT 4.7L/4.7HO V-8...
  • Page 294: Onboard Diagnostic System - Obd Ii

    294 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
  • Page 295: Loose Fuel Filler Cap Message

    Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a clicking sound is heard.
  • Page 296 296 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2.
  • Page 297: Replacement Parts

    vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar parts for normal/scheduled maintenance and repairs is highly recommended to in- sure the designed performance.
  • Page 298: Maintenance Procedures

    298 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
  • Page 299 7. Add oil only if the level is below the “SAFE” range (at or below the “ADD” mark) on the engine oil level indicator (dipstick). Adding one quart of oil when the reading is at the ADD mark will result in a reading at the top of the SAFE zone on these engines.
  • Page 300 300 MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing, Taxi, Police or delivery service (com- mercial service). • Off-Road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
  • Page 301 Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the proper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacture only recommends API Certified engine oils that meet requirements DaimlerChrysler Material Stan-...
  • Page 302: Engine Oil Filter

    302 MAINTAINING YOUR VEHICLE Materials Added to Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.
  • Page 303: Spark Plugs

    Belts should be inspected for evidence of cuts, cracks, glazing, or frayed cords and replaced if there is indication of damage which could result in belt failure. Low gen- erator belt tension can cause battery failure. Also check belt routing to make sure there is no interfer- ence between the belts and other engine components.
  • Page 304: Engine Fuel Filter

    304 MAINTAINING YOUR VEHICLE WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed.
  • Page 305 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
  • Page 306: Maintenance-Free Battery

    Maintenance-Free Battery All Dodge trucks are equipped with maintenance-free batteries. You will never have to add water, nor is periodic maintenance required. WARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds.
  • Page 307: Air Conditioner Maintenance

    To determine the battery charge, check the battery test indicator (if equipped) on top of the battery. Refer to the illustration. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
  • Page 308: Power Steering - Fluid Check

    308 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
  • Page 309: Front Suspension Ball Joints

    WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
  • Page 310: Windshield Wiper Blades

    310 MAINTAINING YOUR VEHICLE also be given to hood latching components to insure proper function. When performing other underhood ser- vices, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring.
  • Page 311: Exhaust System

    WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield.
  • Page 312: Cooling System

    312 MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, fol- low the preceding safety tips. Cooling System Inspection Coolant protection checks should be made at every 12...
  • Page 313 Cooling System Maintenance At the intervals shown in the Maintenance Schedules section of this manual, the system should be drained, flushed and refilled. See your authorized dealer for proper cooling system maintenance. Cooling System — Drain, Flush And Refill If the solution is dirty and contains a considerable amount of sediment, it should be cleaned and flushed.
  • Page 314 314 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified (non- HOAT), may result in engine damage and decreased corrosion protection. If a non-HOAT coolant is intro- duced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
  • Page 315 WARNING! Never add coolant to the radiator when the engine is overheated. Do not loosen or remove pressure cap to cool overheated engine. The coolant is under pres- sure and severe scalding could result. Coolant Pressure Cap The coolant pressure cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant bottle.
  • Page 316: Emission Related Components

    316 MAINTAINING YOUR VEHICLE coolant. Your service attendant should be advised of this. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember A. Do not overfill the coolant bottle. B.
  • Page 317 attention should be given to examining hose surfaces nearest to high heat sources, such as the exhaust mani- fold. Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present.
  • Page 318: Brake System

    318 MAINTAINING YOUR VEHICLE Brake System Power Disc Brakes (Front) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake Master Cylinders The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on.
  • Page 319: Clutch Hydraulic System

    CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Brake Linings Your vehicle is equipped with self-adjusting brakes. During normal driving, a few brake applications while moving in reverse will maintain your brakes at the specified adjustment.
  • Page 320: Manual Transmission

    320 MAINTAINING YOUR VEHICLE Manual Transmission Fluid Level Check This fluid should be checked whenever other underhood services are performed. The fluid level is checked by removing the fill plug. If the level of the lubricant is more than 1/4 (6.35 mm) below the bottom of the filler hole while the vehicle is level, enough lubricant should be added to bring the level to the bottom of the filler hole.
  • Page 321 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operat- ing temperature. Verify that solid coating of oil is seen on both sides of the dipstick.
  • Page 322 Authorized Dodge Dealer or Service Center. It is important that the transmission fluid be maintained at the correct level and that it be drained and refilled as specified.
  • Page 323: Transfer Case

    Transfer Case Inspect the transfer case for fluid leaks. If a fluid leak is evident the transfer case fluid level may be low. Have the transfer case serviced immediately. CAUTION! Damage may result from operation of the vehicle with low transfer case fluid. The transfer case fluid should be drained and refilled at the intervals specified.
  • Page 324: Selection Of Lubricating Grease

    324 MAINTAINING YOUR VEHICLE differential. Rear axle fluid level should be 1/4 (6.35mm) below filler plug hole for 8 1/4 axles and should be 5/8 (16mm) below filler plug for 9 1/4 axles. Front Axle Front Axle fluid level should be at the bottom of the fill plug.
  • Page 325: Appearance Care And Protection From Corrosion

    Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
  • Page 326 326 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
  • Page 327 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. •...
  • Page 328: Power Distribution Center (Fuse/Relay)

    328 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer.
  • Page 329: Vehicle Storage

    contain “Mini”fuses and plug-in “ISO” relays. A label inside the latching cover of the Power Distribution Cen- ters identifies each component for ease of replacement, if necessary. These fuses and relays can be obtained from your dealer. CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
  • Page 330: Replacement Light Bulbs

    330 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Dome Light ......WL212–2 Cargo Light ......567 Overhead Console Lights .
  • Page 331 MAINTAINING YOUR VEHICLE 331 Removing Headlamp Assembly Removing Headlamp Assembly 1. Open the hood. 2. Remove the 3 screws attaching the headlamp housing to the inner panel. 3. Grasp the headlamp and pull firmly to disengage the headlamp housing from the fender panel.
  • Page 332 332 MAINTAINING YOUR VEHICLE 4. While firmly holding the headlamp housing in your hands unlock and disconnect Headlamp bulb connector. 5. Twist 1/4 turn and remove Headlamp bulb from housing and replace. Removing Headlamp Bulb Unlocking Connector 6. Twist 1/4 turn and remove bulb and socket from housing, pull bulb straight out from socket and replace.
  • Page 333 MAINTAINING YOUR VEHICLE 333 Removing Headlamp from Assembly Removing Headlamp Bulb...
  • Page 334: Front Park And Turn Signal Lamp

    334 MAINTAINING YOUR VEHICLE Disconnecting Headlamp Bulb Connector 7. Reverse procedure to install new Headlamp bulb into the headlamp assembly. NOTE: These are Halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life.
  • Page 335 MAINTAINING YOUR VEHICLE 335 Removing Turn Signal Bulb Disconnecting Turn Signal Connector • Rotate bulb socket 1/4 turn and remove socket from housing. • Pull bulb straight from socket. • Reverse procedure to install new turn signal bulb.
  • Page 336: Rear Side Marker, Taillamps/Stoplamp, And Turn Signal Bulbs - Replacement

    336 MAINTAINING YOUR VEHICLE Rear Side Marker, Taillamps/Stoplamp, and Turn Signal Bulbs — Replacement 1. Remove the two (2) screws that pass through the bed sheetmetal. Pulling Housing From Body 2. Pull the taillamp housing straight out from the body. Removing the Two (2) Screws...
  • Page 337 MAINTAINING YOUR VEHICLE 337 3. Rotate the bulb socket from the housing. 4. Pull bulb straight out of socket. Pulling Bulb From Socket Rotating Bulb Socket From Housing...
  • Page 338: Center High-Mounted Stoplamp And Cargo Lamp

    338 MAINTAINING YOUR VEHICLE 5. Reverse Procedure to install bulb and housing. Place the two raised blocks passed the body. Sliding Raised Blocks Past Body Center High-Mounted Stoplamp And Cargo Lamp 1. Remove the two (2) screws holding the housing/lens to the body as shown.
  • Page 339 MAINTAINING YOUR VEHICLE 339 2. Remove housing from Cab. 3. Remove connector from housing tab for more clear- ance. Removing Housing from Cab Removing Connector from Tab...
  • Page 340 340 MAINTAINING YOUR VEHICLE 4. Turn desired bulb socket ⁄ turn and remove socket and bulb from housing. Removing Socket From Housing 5. Pull desired bulb straight from the socket. Pulling Bulb From Socket • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 6.
  • Page 341: License Lamps

    MAINTAINING YOUR VEHICLE 341 2. Rotate the socket 1/4 turn counterclockwise. License Lamps 1. Using a screw driver pry black rubber housing from the bumper. Rotating Socket Removing Housing From Bumper...
  • Page 342: Fog Lamps

    342 MAINTAINING YOUR VEHICLE 3. Pull bulb from socket. Pulling Bulb From Socket 4. Reverse procedure for installation. Fog Lamps 1. Disconnect connector from fog lamp by raising wire harness lock tab and pulling on wire harness connector. 2. Rotate fog lamp bulb 1/4 turn counterclockwise and pull to remove from fog lamp housing.
  • Page 343: Fluids And Capacities

    FLUIDS AND CAPACITIES Fuel 3.7L/4.7L, 87 Octane 4.7L HO, 91 Octane, Recommended Not Required Engine Oil (with filter) 3.7L, SAE 5W-30, API Certified 4.7L, SAE 5W-30, API Certified 4.7L HO, SAE 5W-30, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle 3.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L HO (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula)
  • Page 344: Recommended Fluids, Lubricants And Genuine Parts

    344 MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection 3.7L/4.7L Fuel Selection 4.7L HO Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) P/N 5011764AB or equivalent.
  • Page 345: Chassis

    Chassis Component Automatic Transmission Manual Transmission (Getrag 238) Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant (MS9763).
  • Page 347: Maintenance Schedules

    MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..348 Emissions Testing ..... . . 348 Maintenance Schedules .
  • Page 348: Emission Control System Maintenance

    348 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
  • Page 349: Maintenance Schedules

    MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule “B”. It is for vehicles that are operated under the conditions that are listed below and at the beginning of the schedule. •...
  • Page 350 350 MAINTENANCE SCHEDULES Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the interval that occurs first. NOTE: Under no circumstances should oil change in- tervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
  • Page 351 • Inspect the CV joints (if equipped) and front suspen- sion components. • Check the automatic transmission fluid level (if equipped). MAINTENANCE SCHEDULES 351 • Check the manual transission fluid level (if equipped). • Check the coolant level, hoses, and clamps.
  • Page 352: Schedule "B

    352 SCHEDULE “B” Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. •...
  • Page 353 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect engine air cleaner filter, replace if neces- sary. 3,000 6,000 9,000 (5 000) (10 000) (14 000) (19 000)
  • Page 354 354 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
  • Page 355 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. 33,000 36,000 39, 000 (53 000)
  • Page 356 356 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months which- ever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs.
  • Page 357 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Inspect auto tension drive belt and replace if re- quired.
  • Page 358 358 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
  • Page 359 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Flush and replace engine coolant, if not done at 60 months. Change rear axle fluid. Change front axle fluid (4X4). 93,000 96,000 99,000 (149 000) (154 000)
  • Page 360 360 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
  • Page 361 Miles (Kilometers) Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. (4.7L). Flush and replace engine coolant, if not re- placed at 102,000 miles (163 000 km). This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing.
  • Page 362: Schedule "A

    362 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as neces- sary. Replace spark plugs. 6,000 12,000 18,000 (10 000) (19 000)
  • Page 363 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
  • Page 364 364 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Inspect PCV valve, replace as necessary.** Inspect auto tension drive belt and replace if required.
  • Page 365 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Drain and refill tranfer case fluid (4X4). Flush and replace engine coolant, if not done at 60 months. Flush and replace engine coolant, if not done at 102,000 miles (163 000 km) Inspect brake linings.
  • Page 366 366 SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
  • Page 367: If You Need Consumer Assistance

    IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......368 Prepare For The Appointment .
  • Page 368: Suggestions For Obtaining Service For Your Vehicle

    Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
  • Page 369 This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
  • Page 370: Warranty Information (U.s. Vehicles Only)

    370 IF YOU NEED CONSUMER ASSISTANCE Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires.
  • Page 371 IF YOU NEED CONSUMER ASSISTANCE 371 U.S. Vehicles Only...
  • Page 372: Mopar Parts

    372 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra-...
  • Page 373: Publication Order Forms

    PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals.
  • Page 374 374 IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals...
  • Page 375 INDEX...
  • Page 376 376 INDEX Adding Fuel ......247,273 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 303 Air Conditioner Maintenance .
  • Page 377 Ball Joints ......309 Battery ....... 306 Charging .
  • Page 378 378 INDEX Center High Mounted Stop Light ... . 338 Center Seat Storage Compartment ... . 142 Certification Label ..... . . 252 Changing A Flat Tire .
  • Page 379 Customer Assistance ..... 368 Data Recorder, Event ..... . 57 Daytime Running Lights .
  • Page 380 380 INDEX Block Heater ......198 Break-In Recommendations ....72 Compartment .
  • Page 381 Fluid Capacities ......343 Fluid Level Checks Automatic Transmission ....320 Brake .
  • Page 382 382 INDEX Gross Axle Weight Rating ....253 Gross Cargo Weight ..... . 252 GVWR .
  • Page 383 Intermittent Wipers ..... . 120 Introduction ......4 Jack Operation .
  • Page 384 384 INDEX Low Fuel ......152,153 Malfunction Indicator ....157 Passing .
  • Page 385 Automatic Dimming ..... 82 Electric Powered ..... . . 83 Heated .
  • Page 386 386 INDEX Parking On Hill ......219 Passenger Airbag On/Off Switch ... . . 55 Passing Light .
  • Page 387 Reception, Radio ......159 Reclining Front Seats ..... 108 Recommended Fluids, Lubricants and Genuine Parts .
  • Page 388 388 INDEX Inspection ......74 Pretensioners ......38 Reminder .
  • Page 389 Emergency (Jump Starting) ....283 Engine Block Heater ....198 Steering Column Controls .
  • Page 390 390 INDEX Load Capacity ..... 229,230 Radial ......236 Replacement .
  • Page 391 Maintenance ......320 Manual ......196,204,320 Shifting .
  • Page 392 392 INDEX Windshield Washers ....120,121,310 Fluid ......120,310 Windshield Wiper Blades .

This manual is also suitable for:

2005 nd dakota

Table of Contents

Save PDF