Page 2: Vehicles Sold In Canada
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution there- fore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 7 INTRODUCTION 5...
Page 8: Warnings And Cautions
The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel and is visible from outside the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Vehicle Identification Number Label affixed to a window on your vehicle, the vehicle NOTE: It is illegal to remove the VIN.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Key-In-Ignition Reminder .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Locks ......25 Manual Door Lock ..... 26 Power Door Locks .
Page 13: Periodic Safety Checks You Should Make
Safety Tips ......60 Exhaust System ..... . . 60 Safety Checks You Should Make Inside The Vehicle .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle’s locks. These numbers can be used to order duplicate keys from your authorized dealer or a locksmith.
Page 15: Key-In-Ignition Reminder
NOTE: The Power Accessory Delay feature allows you to operate the radio and the power windows for two minutes after turning OFF the ignition switch. Removing the key from the ignition switch and opening the driver’s door will cancel this feature. Your authorized dealership can enable or disable the Power Accessory Delay feature as desired.
Page 16 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE arm itself in approximately 16 seconds. During the arming process, the Vehicle Security Light will flash at a fast rate. Once the system is armed, the light will flash once every six seconds. Vehicle Security Light NOTE: The system will not cancel the arming process if you...
Page 17 Entering the Trunk with the System Armed — Convertible NOTE: Using the key to open the trunk while the system is armed will trigger the alarm. Press the TRUNK button on the RKE transmitter to allow access without triggering the alarm or having to disarm the system.
Page 18: To Disarm The System
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System There are two ways to disarm the system: Use the key to unlock the driver’s door. The door lock is located on the outside door panel beneath the mirror.
Page 19: Electronic Immobilization System - Canada Only
Electronic Immobilization System — Canada Only The Electronic Immobilization system prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. To Arm the System The Electronic Immobilization system will passively arm 30 seconds after the key is removed from the vehicle.
Page 20: Illuminated Entry System
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The interior lights will turn on whenever a door is opened or the liftgate is opened (Coupe models) and the dimmer switch is not in the defeat position. The interior lights will turn on, remain on for about 30 seconds, and then fade to off if any of the following occur: A door is opened using the outside door handle and...
Page 21 UNLOCKED will flash in the odometer if one door is unlocked or will remain on steadily if both doors are unlocked. NOTE: On Coupe models, pressing either the UNLOCK button or the LIFTGATE button will allow liftgate access. Remote Key Unlock, Driver Door/Both Doors First This feature lets you program the system to unlock either the driver’s door or both doors on the first press of the UNLOCK button on the RKE transmitter.
Page 22: To Lock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights with Remote Key Lock This feature will cause the park lights and turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off.
Page 23: To Unlatch The Trunk/Liftgate
2. Release both buttons at the same time. 3. Test the feature while outside of the vehicle, by pressing the LOCK button on the RKE transmitter with the ignition in the OFF/LOCK position, and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting.
Page 24: Programming Additional Transmitters
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters NOTE: You must have at least one programmed RKE transmitter to perform this procedure. If you do not have a programmed RKE transmitter, contact your authorized dealer for details. Use this procedure to program up to three additional transmitters for your vehicle.
Page 25: Battery Replacement
Battery Replacement The recommended replacement battery is 2016. This is a generic battery, readily available at local retail stores. NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Do not touch the battery terminals that are on the back housing or the printed circuit board.
Page 26: General Information
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To assemble the RKE transmitter case, snap the two halves together. 4. Test the RKE transmitter operation. General Information This RKE transmitter complies with FCC rules Part 15. Operation is subject to the following conditions: 1.
Page 27: Things To Know Before Starting Your Vehicle 25
DOOR LOCKS WARNING! Do not touch the exhaust pipe sill covers when entering or exiting your vehicle. They can be hot enough to burn you. Observe the warning labels on each door closure panel. For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
Page 28: Manual Door Lock
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Door Lock The driver’s door can be locked or unlocked with the key. The door lock is located on the outside door panel beneath the mirror. Mechanical Door Lock Power Door Locks A power door lock switch is on each door trim panel.
Page 29 Electronic Door Lock This vehicle is equipped with a virtual lock system. Input from the outside door handle is ignored if the vehicle is virtually locked. Door Lock Messaging The words “DOOR UNLOCKED” will flash in the odom- eter if one door is unlocked or will remain on steadily if both doors are unlocked.
Page 30: Windows
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature can also be disabled at an authorized deal- ership if desired. NOTE: Use the Automatic Door Locks feature in accor- dance with local laws. WINDOWS Power Windows The power window switches are located between the driver and passenger seats on the center tunnel bezel, just to the left of the parking brake.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power win- dows while operating the power window switch. Such entrapment may result in serious injury or death.
Page 32: Auto Down Feature
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Feature Both windows have an Auto Down feature. Press the WINDOW switch to the second detent, release, and the window will go down automatically. Press the switch a second time in either direction to stop the window. To open the window to a desired position, press and hold the WINDOW switch in the first detent.
Page 33 NOTE: The liftgate release switch will be ignored under the following conditions: When the ignition is in RUN and the parking brake is not set. When vehicle speed is not 0 mph (0 km/h). When all doors are locked (except for RKE transmitter liftgate access).
Page 34: Trunk Lock And Release - Convertible Models Only
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE — CONVERTIBLE MODELS ONLY You can unlatch the trunk lid by pressing the TRUNK button on the Remote Keyless Entry (RKE) transmitter for at least one second. The park lights and turn signal lights will flash three times to acknowledge the signal and the trunk lid will pop open.
Page 35: Trunk Emergency Release
Trunk Emergency Release The trunk of your vehicle is equipped with an emergency release handle. It is located on the inside of the trunk lid, near the latch, and is coated so that it glows in a darkened trunk. Pull on the handle to open the trunk. Emergency Release THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 OCCUPANT RESTRAINTS...
Page 36: Lap/Shoulder Belts
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your street.
Page 37 WARNING! (Continued) Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 4. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 39 WARNING! (Continued) A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug.
Page 41: Lap/Shoulder Belt Untwisting Procedure
Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 42: Automatic Locking Mode
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Buckle the driver’s seat belt. 4. Turn the ignition switch to the ON/RUN position, but do not start the engine. Wait for the Seat Belt Reminder Light to turn off and then proceed to the next step. NOTE: You must perform the following steps within 60 seconds of turning the ignition switch to the ON/RUN position.
Page 43: Seat Belts And Pregnant Women
How to Engage the Automatic Locking Mode To convert the passenger seat belt from emergency lock- ing mode to automatic locking mode, grasp the shoulder portion of the belt and pull all of the webbing out of the retractor. Then, allow some of the webbing to retract back into the retractor.
Page 44: Driver And Passenger Supplemental Restraint System (Srs) - Airbag
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use a seat belt extender when the seat belt is not long enough when worn low and snug and in the recom- mended seating positions.
Page 45 WARNING! (Continued) Do not drill, cut, or tamper with the knee bolster in any way. Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizens band radios, etc. Relying on the airbags alone could lead to more severe injuries in a collision.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. An infant up to one year or approximately 20 lbs (9 kg) should never ride in the vehicle because in the event of a crash, the rear-facing child seat places them too close to the passenger airbag.
Page 47 9. Read the instructions provided with your child safety seat or booster seat to make sure that you are using it properly. 10. All occupants should wear their lap and shoulder belts properly. 11. Position the driver seat and passenger seat as far away from the instrument panel as practical to allow the airbags room to inflate.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE − Interconnecting Wiring − Seat Track Position Sensors How the Airbag System Works The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. The airbag inflators are designed to provide different rates of inflation.
Page 49 WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If there is a fault present in the OCS, the Airbag Warning Light will turn on. This indicates that you should take the vehicle to an authorized dealer for service. The Airbag Warning Light will turn on when- ever there is fault present, which can affect the opera- tion of the airbag system.
Page 51 and for most properly installed child restraint systems. However, under certain conditions, even with a properly installed child restraint system, the PAD Indicator Light may not be on, even though the airbag is disabled. This can occur if the child restraint is lighter than the thresh- old weight necessary to turn the PAD Indicator Light on.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE proper airbag deployment. Do not make any modifica- tions to the passenger seat components, assembly, or to the seat cover. If the seat, trim cover, or cushion needs service for any reason, take the vehicle to your autho- rized dealer.
Page 53 If a Deployment Occurs The airbag system is designed to deploy when the ORC detects a moderate-to-severe frontal collision, to help restrain the driver and passenger, and then to deflate immediately. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. Maintaining Your Airbag System WARNING! Modifications to any part of the airbag system could cause it to fail when you need it.
Page 55: Child Restraint
Airbag Warning Light You will want to have the airbags ready for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an autho- rized dealer service the system immediately: The Airbag Warning Light does not come on or flickers during the six to eight seconds when the ignition switch is first turned on.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat Owner’s Manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child: Infant and Child Restraints Safety experts recommend rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
Page 57 The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 59 3. Remove the child tether access cover by prying either side with a screwdriver or similar tool, as shown. Child Tether Access Cover NOTE: While the child tether is in use, keep the access cover in a safe place so that it can be replaced after use of the child tether.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Return the seatback to an upright position. 8. Install the child restraint according to the manufactur- er’s directions. 9. Remove slack from the tether strap according to the child restraint manufacturer’s directions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the...
Page 61: Break-In Recommendations
3. Allow some of the webbing to retract back into the retractor. As the belt retracts, you will hear a clicking sound indicating that the belt is now in automatic locking mode. 4. Tighten the lap portion of the belt and allow the excess webbing to retract back to the retractor.
Page 62: Safety Tips
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Avoid excessive idling. Check the engine oil level at every fuel fill. NOTE: A new engine will consume some oil during the first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as a sign of difficulty.
Page 63: Vehicle
mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace or adjust as required. Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts,...
Page 64: Outside The Vehicle
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and side wall for cuts and cracks.
Page 65: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation — If Equipped ..65 To Lower The Top ..... 65 To Raise The Top .
Page 66 64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-On Reminder ....84 Battery Saver Feature — Exterior Lights ..84 Fog Lights .
Page 67: Convertible Top Operation - If Equipped
CONVERTIBLE TOP OPERATION — IF EQUIPPED WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore, it is important that all occupants wear their seat belts at all times when riding in a convertible.
Page 68: To Raise The Top
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Depress the button located at the top of the latch and then pull the latch handle downward and rearward. Unlatching Convertible Top 4. Disengage the latch hook from the windshield receiver rod and then pull the latch all the way back to the detent stow position.
Page 69 4. Press downward on the convertible top and then press the lever behind the driver seat to release the downstack latch. Convertible Top Latch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 5. Manually raise the convertible top until it meets the windshield header.
Page 70 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. From inside the vehicle, grasp the handles and pull the convertible top toward the windshield header. Then, push the latch handle forward so that the latch hook engages the windshield receiver rod. Aligning Convertible Top 8.
Page 71: Convertible Top Boot Cover Installation - If Equipped
NOTE: Until the convertible top system has had ad- equate time to break-in, it may take a greater effort to engage the latch hook and close the latch. However, several weeks of normal convertible top usage will reduce these efforts. 9.
Page 72 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Slide the boot cover pocket over the front corner of the convertible top on the driver side of the vehicle. Then, stretch and slide the boot cover pocket over the front corner of the convertible top on the passenger side of the vehicle.
Page 73 6. On the passenger side of the vehicle, clip the tab under the trunk lid stop and on the outer edge of the quarter panel flange. Attaching Passenger Side Tab UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 7. Push downward on the boot cover pocket to engage the inboard tab.
Page 74 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. On the driver side of the vehicle, clip the tab under the trunk lid stop and on the outer edge of the quarter panel flange. Attaching Driver Side Tab 9. Push downward on the boot cover pocket to engage the inboard tab.
Page 75 10. Push downward on the boot cover behind driver seat to lock down the boot cover. 11. Stretch and smooth out the boot cover from the rear of vehicle. Stretching and Smoothing Cover UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 12.
Page 76: Convertible Top Boot Cover Removal And Storage
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Open the trunk. 2. On the driver side of the vehicle, pull upward on the boot cover to disengage the inboard tab. Disengaging Driver Side Tab 3.
Page 77 4. On the passenger side of the vehicle, pull upward on the boot cover to disengage the inboard tab. Disengaging Passenger Side Tab UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 5. Unclip the tab under the trunk lid stop and on the outer edge of the quarter panel flange.
Page 78: Understanding The Features Of Your Vehicle 63
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Slide the boot cover pockets off the front corners of the convertible top. 7. Fold the outer edges of the boot cover inward. Folding Outer Edges 8. Fold the boot cover again. Folding Boot Cover 9.
Page 79: Mirrors
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A pivot system allows for horizontal and verti- cal mirror adjustment. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 80: Power Mirrors
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
Page 81: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 NOTE: When not in use, return the power mirror switch to the neutral (off) position to prevent accidental mirror movement. SEATS Manual Seat Adjustments Forward and Rearward Adjustment The adjusting bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rear- ward.
Page 82 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 83: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Reach into the lower right grille opening and pull the primary hood latch forward. Hood Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 2.
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Assist props will raise the hood to a normal usage position. If greater access is required, the hood may be pushed up at the front, raising the hood beyond the initial opening height. CAUTION! Do not leave the hood open in areas where strong gusts of wind are likely.
Page 85: Lights
LIGHTS Exterior and Interior Lighting Control The multifunction lever on the left side of the steering column controls the operation of the headlights, parking lights, turn signal lights, front fog lights, instrument panel lights, and interior lights. Multifunction Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation.
Page 86: Daytime Running Lights
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This feature can be disabled at the authorized dealership, if so desired. Daytime Running Lights The fog lights will come on as Daytime Running Lights, whenever the ignition switch is ON, the headlights are off, and the parking brake is off.
Page 87: Turn Signals
Turn Signals Move the multifunction lever upward or downward and the corresponding turn signal indicator on the instru- ment panel will flash to show proper operation of the front and rear turn signal lights. Turn Signal Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 You can also signal a lane change by moving the lever partially upward or downward without moving beyond the detent.
Page 88: High Beam/Low Beam Select Switch
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Pull the multifunction lever toward you to switch the headlights to high beam. Pull the lever a second time to switch the headlights back to low beam. Headlight Beam Control Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you.
Page 89 A door is unlocked using the outside driver’s door key cylinder. The interior lights will turn on and remain on for about four seconds and then fade to off if a door is opened using the inside door handle. Courtesy/Reading Lights Two courtesy/reading lights are located in the bottom of the rearview mirror.
Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature — Interior Lights To protect the battery, the interior lights will turn off automatically 15 minutes after the ignition switch is moved to the OFF/LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open or the liftgate is open (Coupe models).
Page 91: Windshield Wipers And Washers
Interior Light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom OFF position. The inte- rior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle). This feature brightens the odometer and radio dis- play when the parking lights or head- lights...
Page 92: Intermittent Wiper System
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE intermittent DEL setting for Low-speed wiper operation, or to the second detent past the intermittent DEL setting for High-speed wiper operation. CAUTION! Turn the windshield wipers off when driving through an automatic car wash. Damage to the wind- shield wipers may result if the wiper switch is left in any position other than off.
Page 93: Windshield Washers
Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the windshield wiper is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
Page 94: Adjustable Pedals
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 95 To adjust the pedals: 1. Adjust the seat and steering column to a comfortable position. 2. Either press the adjustable pedals switch forward to move the pedals forward (toward the front of the ve- hicle), or pull the switch rearward to move the pedals rearward (toward the rear of the vehicle).
Page 96: Adjustable Foot Rest
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Foot Rest This feature allows the driver to adjust the foot rest forward or backward and to rotate it upward or down- ward to allow for greater driving comfort. Adjustable Foot Rest To adjust the pedal: 1.
Page 97: Rear Window Features
REAR WINDOW FEATURES Electric Rear Window Defroster The electric rear window defroster control is lo- cated on the climate control. Press this button to turn on the rear window defroster. A light above the button will illuminate when the rear window defroster is ON.
Page 99: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....99 Instrument Cluster Description ... . 100 Speedometer .
Page 100 98 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode In RBB, RAH, REV And RBK Radios ..... 122 Selecting Satellite Mode In RBP, RBU, RAZ, RB1 And RBQ Radios .
Page 101: Instrument Panel Features
INSTRUMENT PANEL FEATURES 1 - Air Outlet 2 - Sound System Speaker 3 - Main Message Center 4 - Fuel Gauge 5 - Auxiliary Message Center 6 - Tachometer UNDERSTANDING YOUR INSTRUMENT PANEL 99 7 - Speedometer/Odometer 8 - Oil Pressure Gauge 9 - Passenger Airbag Off Light 10 - Passenger Airbag 11 - Glove Compartment...
Page 102: Instrument Cluster Description
100 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION Speedometer Shows the vehicle’s speed in miles- per-hour (mph) and kilometers-per- hour (km/h). Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. NOTE: U.S. federal regulations require upon transfer of vehicle ownership, the seller certify the mileage the vehicle has been driven.
Page 103: Message Center
The word “DECK” will flash in the display if the trunk/liftgate is open. The words “LOW TIRE” will flash slowly in the display and a chime will sound if the tire pressure is low. The words “FLAT TIRE” will flash rapidly in the display and a chime will sound if critically low tire pressure is detected.
Page 104 102 UNDERSTANDING YOUR INSTRUMENT PANEL This light also illuminates at vehicle start-up to indicate that the ABS self-check is in process. If the light remains on after start-up, or turns on and remains on at road speeds, it may indicate a system malfunction or that the system is inoperative.
Page 105 Certain conditions such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the light after engine start. The vehicle should be serviced if the light remains on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing.
Page 106 104 UNDERSTANDING YOUR INSTRUMENT PANEL Brake Warning Light The red Brake System Warning Light turns on when the ignition is first turned on. It should stay on briefly as a bulb check. If the light does not turn on during starting, have it repaired promptly. If the light remains on following the bulb check, it may be an indication that the parking brake is not released.
Page 107 If the light turns on steady while the engine is running, safely bring the vehicle to a complete stop as soon as possible, cycle the ignition key, and then restart the engine. The light should turn off. However, if the light remains on steady, see your authorized dealer for service as soon as possible.
Page 108 106 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated.
Page 109: Gauges And Indicator Lights
WARNING! Do not exceed 55 mph (88 km/h) if the LOW Tire indicator is activated. Vehicle handling and braking may be reduced. You could have an accident and be severely or fatally injured. Seat Belt Reminder Light If the driver does not buckle their seat belt and vehicle speed exceeds 5 mph (8 km/h), or if the passenger does not buckle their seat belt within 10 seconds of vehicle speed exceeding 5 mph (8 km/h),...
Page 110 108 UNDERSTANDING YOUR INSTRUMENT PANEL 6000 RPM. This serves as a visual aid to shift before reaching the red line. This warning will turn off when the tachometer pointer falls below 5900 RPM. Coolant Temperature Gauge This gauge shows the engine coolant tempera- ture.
Page 111 This gauge does not indicate the amount of oil in the engine. The engine oil level must be checked under the hood. Check the level often during severe usage. Oil Pressure Warning Light The red Oil Pressure Warning Light is located in the Oil Pressure Gauge.
Page 112: Setting The Digital Clock
110 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The accessory belt also drives the water pump. Op- erating the vehicle with a failed belt can cause engine overheating and possible severe engine damage. SETTING THE DIGITAL CLOCK The digital display panel on the radio displays the time in hours and minutes.
Page 113: Sales Code Rah - Am And Fm Stereo Radio With Cd Player And Cd/Dvd Changer Controls
SALES CODE RAH — AM AND FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. RAH Radio UNDERSTANDING YOUR INSTRUMENT PANEL 111 Radio Operation Power/Volume Control Push the ON/VOL control to turn the radio on.
Page 114 112 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the TUNE button to select the following format types: Program Type Adult Hits Adult Hit Classical Classical Classic Rock Classic Rock College College Country Country Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalgia Oldies...
Page 115 The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 116 114 UNDERSTANDING YOUR INSTRUMENT PANEL Tone Control The Bass and/or Treble controls sound for the desired tone. Press the AUDIO button, select Bass or TREBLE, then press SEEK + or SEEK amplification of the band. To Set the Radio Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button.
Page 117: Cd Player Operation
NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
Page 118: Cd/Dvd Changer Operation
116 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 119: Notes On Playing Mp3 Files
Time Press the TIME button to change the display from elapsed CD or DVD playing time to time of day. Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions.
Page 120 118 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Page 121: Operation Instructions
Playback of MP3 files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: Media - CD-RW media may take longer to load than...
Page 122: Satellite Radio - If Equipped
120 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD Mode for MP3 Play) Press the FF side of the button to move forward through the MP3 selection. Press the RW side of the button to move back through the MP3 selection. AM/FM Button (CD Mode for MP3 Play) Switches the Radio into the AM or FM Radio mode.
Page 123: System Activation
System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of SIRIUS audio service that is included with the factory- installed satellite radio system in your vehicle. Sirius will contact you to supply a welcome kit and to confirm subscription information, including the set up of your on-line listening account at no additional charge.
Page 124: Selecting Satellite Mode In Rbb, Rah, Rev And Rbk Radios
122 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access with RBP, RBU, RAZ, RB1 and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for three seconds. All twelve ESN/SID numbers will be displayed.
Page 125: Storing And Selecting Pre-Set Channels
and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and release the SCAN button (if equipped) to automatically change channels every seven seconds. The radio will pause on each channel for seven seconds before moving on to the next channel.
Page 126: Pty (Seek) Button
124 UNDERSTANDING YOUR INSTRUMENT PANEL PTY (SEEK) Button When the desired program is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped).
Page 127: Radio Operation And Cellular Phones
3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7.
Page 128: Air Conditioning And Heating System
126 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating System Air Conditioning And Heater Controls Blower Control Use this control to regulate the amount of air forced through the sys- tem in any mode you select. Turn the control clockwise to increase fan speed.
Page 129 Temperature Control Use this control to regulate the tem- perature of the air inside the passen- ger compartment. The blue area of the control indicates cooler temperatures while the red area indicates warmer temperatures. Mode Control Use this control to select the direction of air flow.
Page 130 128 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is a varying temperature differential be- tween the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature provides improved comfort during sunny but cool con- ditions.
Page 131: Operating Tips
Operating Tips NOTE: Refer to the chart at the end of this section for suggested control settings for various weather condi- tions. Summer Operation The engine cooling system in air-conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating.
Page 132 130 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly re- moved by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side win- dow fogging becomes a problem increase blower speed.
Page 133: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....134 Normal Starting ..... 135 If Engine Fails To Start .
Page 134 132 STARTING AND OPERATING Anti-Lock Brake System ....148 Tire Safety Information ....151 Tire Markings .
Page 135 Materials Added To Fuel ....173 Fuel System Cautions ....173 Carbon Monoxide Warnings .
Page 136: Starting And Operating
134 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct any other occupant to buckle their seat belt. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
Page 137: Normal Starting
Normal Starting CAUTION! The engine in your vehicle is designed for operation down to 0°F (-18°C). Starting the engine below 0°F (-18°C) creates a potential for scuffing or seizing of internal components in this very high performance engine. To prevent engine damage, do not start the engine at temperatures below 0°F (-18°C).
Page 138: If Engine Fails To Start
136 STARTING AND OPERATING 6. Press the red ENGINE START button located on the instrument panel. Release the button when the engine starts. ENGINE START Button If Engine Fails to Start CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time.
Page 139: After Starting
WARNING! (Continued) Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
Page 140 138 STARTING AND OPERATING CAUTION! Failure to depress the clutch pedal fully to the floor may cause increased shift efforts, and may result in damage to the clutch and transmission. Be sure the transmission is in FIRST gear when moving forward from a standing position.
Page 141: Recommended Shift Speeds
Shifting gears during cold weather may require an increased effort until the transmission lubricant is warm. This is normal and not harmful to the transmis- sion. Due to the high performance nature of your drivetrain, a certain amount of noise from the transmission is normal.
Page 142 140 STARTING AND OPERATING FIRST gear, and the accelerator is at 1/4 throttle or less. The Skip Shift Indicator Light located in the tachometer will turn Amber during these times. When the indicator light turns amber, the shift mecha- nism will only allow shifts from FIRST gear to FOURTH gear.
Page 143: Driving On Slippery Surfaces
DRIVING ON SLIPPERY SURFACES Acceleration WARNING! Rapid acceleration on slippery surfaces is dangerous. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road...
Page 144: Driving Through Water
142 STARTING AND OPERATING DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on or cross a road or a path where water is flowing and/or rising (as in storm run-off).
Page 145 CAUTION! (Continued) Driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of con- tamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
Page 146: Power Steering
144 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 147: Parking Brake
apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading.
Page 148 146 STARTING AND OPERATING drops into the handle (releasing the lock), guide the handle downward to its stop and then release the button and the handle. Parking Brake The Brake System Warning Light in the instrument cluster will turn on when the ignition is in the ON/RUN position and the parking brake is applied.
Page 149: Brake System
BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during application, greater pedal force required to slow or stop, and potential activation of the Brake System Warning Light.
Page 150: Anti-Lock Brake System
148 STARTING AND OPERATING Safe Operating Tips WARNING! To use your brakes and accelerator more safely, follow these tips: Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage.
Page 151 NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning. The Anti-Lock Brake System conducts a low-speed self- test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occurring, you may feel slight pedal movement.
Page 152 150 STARTING AND OPERATING WARNING! (Continued) Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond...
Page 153: Tire Safety Information
Anti-Lock Brake Warning Light The amber Anti-Lock Brake Warning Light will turn on and stay on briefly as a bulb check when the ignition is first turned on. If the light does not turn on during starting, have it re- paired promptly.
Page 154 152 STARTING AND OPERATING NOTE: P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. European-Metric tire sizing is based on European design standards.
Page 155 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%)
Page 156 154 STARTING AND OPERATING Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 157: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, DOT = Department of Transportation —...
Page 158: Tire Loading And Tire Pressure
156 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle...
Page 159 NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg”...
Page 160 158 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calcu- late total load, cargo/luggage, and towing capacities...
Page 161 STARTING AND OPERATING 159...
Page 162: Tires - General Information
160 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 163: Tire Inflation Pressures
WARNING! (Continued) Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 164: Tire Pressures For High Speed Operation
162 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 165: Radial Ply Tires
loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail.
Page 166: Tire Spinning
164 STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h). For additional information, refer to “Freeing A Stuck Vehicle” in Section 6. WARNING! Fast spinning tires can be dangerous.
Page 167: Life Of Tire
These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 168: Replacement Tires
166 STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed.
Page 169: Tire Storage
WARNING! (Continued) Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings.
Page 170 168 STARTING AND OPERATING Rotate the tires “side-to-side” as shown in the diagram. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
Page 171: Tire Pressure Monitor System (Tpms)
TIRE PRESSURE MONITOR SYSTEM (TPMS) Low Tire Indicator If tire pressure falls below 23 psi (159 kpa), the Low Tire Pressure Telltale in the Message Center will illuminate, a chime will sound, and the words LOW TIRE will flash slowly in the Liquid Crystal Display (LCD) panel in the bottom of the speedometer.
Page 172: Fuel Requirements
170 STARTING AND OPERATING TPMS Malfunction Warning Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated.
Page 173: Reformulated Gasoline
If you experience these symptoms, try another brand of “premium” gasoline before considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) which...
Page 174: E-85 Usage In Non-Flex Fuel Vehicles
172 STARTING AND OPERATING Problems that result from using methanol/gasoline or E85 Ethanol blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline contain- ing 10% ethanol (E10).
Page 175: Materials Added To Fuel
content of gasoline may not be indicated on the pump, you should ask your gasoline retailer if his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than allowed in the United States.
Page 176: Carbon Monoxide Warnings
174 STARTING AND OPERATING The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not the responsibility of the manufacturer.
Page 177: Adding Fuel
ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door above the rear tire on the passenger side of the vehicle. To access the gas cap, grasp the finger pull (on the left side of the fuel filler door) and pull it open.
Page 178: Trailer Towing
176 STARTING AND OPERATING WARNING! Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. Never add fuel to the vehicle when the engine is running. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle.
Page 179: Ground Clearance
GROUND CLEARANCE The front and rear fascias and side sills ride low and ground clearance is limited. CAUTION! Damage to the front and rear fascias and side sills can occur if you disregard the low ground clearance in these areas of your vehicle. Pay close attention when parking to avoid running into parking curbs.
Page 181: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....180 If Your Engine Overheats ....180 TIREFIT Kit .
Page 182: Hazard Warning Flasher
180 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is on the top of the steering column, just behind the steering wheel. Hazard Warning Switch Press the Hazard Warning flasher switch and all front and rear directional signals will flash. Press the switch a second time to turn the flashers off.
Page 183: Tirefit Kit
In city traffic — While moving, shift into the highest gear possible to reduce engine RPM. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat.
Page 184: Tirefit Storage
182 WHAT TO DO IN EMERGENCIES TIREFIT Storage The TIREFIT kit is located in the trunk. TIREFIT Location TIREFIT Usage Precautions NOTE: Replace the TIREFIT Sealant Bottle prior to the expi- ration date (printed on the bottle label) to assure optimum operation of the system.
Page 185 only the Black Air Pump Hose 6 and make sure the Mode Select Knob 4 is in the Air Mode when inflating such items to avoid injecting sealant into them. The TIREFIT Sealant is only intended to seal small punc- tures in the tire tread of a tire on this vehicle.
Page 186 184 WHAT TO DO IN EMERGENCIES WARNING! (Continued) Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you. WARNING! Take care not to allow the contents of TIREFIT to come in contact with hair, eyes, or clothing.
Page 187: Tirefit Kit Components And Operation
TIREFIT Kit Components and Operation 1. Sealant Bottle 2. Pressure Gauge 3. AIR PUMP POWER Button 4. Mode Select Knob WHAT TO DO IN EMERGENCIES 185 5. Power Plug and Cable 6. Air Pump Hose (Black) 7. Sealant Hose (Clear with Yellow Cap) 8.
Page 188: Sealing A Tire With Tirefit
186 WHAT TO DO IN EMERGENCIES Using the Air Pump Power Button Push and release the button 3 once to turn ON the TIREFIT kit. Push and release the button 3 again to turn OFF the TIREFIT kit. Sealing a Tire with TIREFIT A.
Page 189 5. Remove the cap from the valve stem and then screw the fitting at the end of the Sealant Hose 7 onto the valve stem. 6. Uncoil the Power Plug and Cable 5 and then insert the plug into the vehicle’s power outlet. NOTE: Do not remove foreign objects (e.g., screws or nails) from the tire.
Page 190 188 WHAT TO DO IN EMERGENCIES D. After Injecting TIREFIT Sealant 1. Allow the air pump to inflate the tire to the pressure indicated on the tire pressure label on the driver-side latch pillar. Check the pressure in the tire by looking at the Pressure Gauge 2.
Page 191 WARNING! TIREFIT is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using TIREFIT. Do not exceed 55 mph (90 km/h) until having the tire repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you.
Page 192 190 WHAT TO DO IN EMERGENCIES 7. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer or tire ser- vice center. 8. Replace the Sealant Bottle 1 at your nearest authorized Mopar parts dealership as soon as possible. Refer to “H. Sealant Bottle Replacement.”...
Page 193 H. Sealant Bottle Replacement 1. Uncoil the Clear Sealant Hose 7. 2. Locate the rectangular SEALANT BOTTLE RELEASE button in the recessed area where you place your fingers to unlatch the hoses 6 and 7 from their storage area. 3. Use the Yellow Cap on end of the Clear Sealant Hose 7 to depress the SEALANT BOTTLE RELEASE button.
Page 194: Jump-Starting Procedures
192 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES WARNING! Take care to avoid the radiator cooling fans when- ever the hood is raised. They can start anytime the ignition switch is on. You can be hurt by the fans. Take care to avoid the accessory drive whenever the hood is raised.
Page 195 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles touch one another.
Page 196 194 WHAT TO DO IN EMERGENCIES 7. If you are jump-starting another vehicle, connect one end of a jumper cable to the remote jump-start positive post (+). Connect the other end of the same cable to the positive (+) terminal of the discharged battery. 8.
Page 197: Freeing A Stuck Vehicle
NOTE: The Vehicle Security Alarm System will prevent the engine from starting. 12. Start the engine in the vehicle with the discharged battery. If engine does not start in 15 seconds, stop cranking engine and allow starter to cool down before cranking again.
Page 198: Towing A Disabled Vehicle
196 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE Do not tow with sling type equipment. Only use flat bed equipment. Always comply with applicable state or local towing ordinances. CAUTION! Towing with equipment other than flat bed types may damage your vehicle.
Page 199: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 8.4L ... . . 199 Onboard Diagnostic System (OBD II) ..200 Emissions Inspection And Maintenance Programs .
Page 200 198 MAINTAINING YOUR VEHICLE Brake System ..... . . 222 Manual Transmission ....224 Hydraulic Clutch .
Page 201: Engine Compartment - 8.4L
ENGINE COMPARTMENT — 8.4L 1 — Coolant Pressure Cap 2 — Engine Oil Dipstick 3 — Power Distribution Center 4 — Remote Jump Start Positive Battery Post 5 — Brake Fluid Reservoir MAINTAINING YOUR VEHICLE 199 6 — Clutch Fluid Reservoir 7 —...
Page 202: Onboard Diagnostic System (Obd Ii)
200 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems.
Page 203: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states that require an Inspection and Mainte- nance (I/M), this check verifies the Malfunction Indicator Light (MIL) is functioning and is not on when the engine is running, and that the OBD II system is ready for testing.
Page 204: Replacement Parts
202 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
Page 205: Dealer Service
DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 206 204 MAINTAINING YOUR VEHICLE The best time to check the oil level is approximately five minutes after a fully warmed engine is turned off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground also will improve the accuracy of the oil level readings.
Page 207 Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or SM/CF, and meet the requirements of Chrysler Material Standard MS-10725.
Page 208: Engine Oil Filter
206 MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil Do not add supplemental materials, other than leak detection dyes, to the engine oil.
Page 209: Maintenance-Free Battery
WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed.
Page 210 208 MAINTAINING YOUR VEHICLE To gain access to the battery, remove the floor portion of the rear compartment carpet. Battery Location Accessing The Battery...
Page 211 WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 212: Battery Save Feature
210 MAINTAINING YOUR VEHICLE Battery Save Feature The Battery Save feature conserves battery power when storing the vehicle. It allows for up to three months of storage time without losing radio and engine controller memory. Using this feature is an alternative to discon- necting the battery.
Page 213: Air Conditioner Maintenance
The Vehicle Security Alarm is disabled when the Battery Save Feature is enabled. Therefore, the vehicle is not protected when the Battery Save Feature is enabled. The exterior and interior lighting functions will not work when the Battery Save Feature is enabled. To Deactivate the Battery Save Feature 1.
Page 214: Body Lubrication
212 MAINTAINING YOUR VEHICLE WARNING! Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
Page 215: Windshield Wiper Blades
attention should also be given to hood latching compo- nents to insure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
Page 216: Exhaust System
214 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or side of the vehicle is damaged;...
Page 217 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. Have your vehicle serviced promptly in the event of engine malfunction, particularly when involving en- gine misfire or other apparent loss of performance. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 218: Cooling System
216 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- age: Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. Do not try to start the engine by pushing or towing the vehicle.
Page 219 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (anti- freeze).
Page 220 218 MAINTAINING YOUR VEHICLE CAUTION! Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible.
Page 221 When adding engine coolant (antifreeze): The manufacturer recommends using MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below 34°F ( 37°C) are anticipated.
Page 222 220 MAINTAINING YOUR VEHICLE WARNING! The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 223 of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming...
Page 224: Brake System
222 MAINTAINING YOUR VEHICLE Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat.
Page 225 Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reser- voir. Overfilling of fluid is not recommended because it may cause leaking in the system.
Page 226: Manual Transmission
224 MAINTAINING YOUR VEHICLE Change Brake Fluid Brake fluid will tend to absorb moisture from the atmo- sphere over time. If the fluid becomes contaminated with water, brake performance will deteriorate. Therefore, the brake fluid must be changed at the intervals specified in “Maintenance Schedules”...
Page 227 Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to the reservoir. Do Not Overfill. Overfilling can cause clutch release problems as the clutch wears. A low fluid level may indicate a leak, in which case, hydraulic clutch linkage replacement may be required.
Page 228: Rear Axle
226 MAINTAINING YOUR VEHICLE Rear Axle Axle Lubricant Level Check Check the exterior of the axle for evidence of gear oil leakage every 12 months or 6,000 miles (10 000 km). This check should be made with the vehicle level and sup- ported by the suspension, with the vehicle on the ground or raised on an axle and wheel type hoist.
Page 229 Washing Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR Car Wash or a mild car wash soap, and rinse the panels completely with clear water. If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR Super Kleen Bug and Tar Remover to remove.
Page 230 228 MAINTAINING YOUR VEHICLE Convertible Top Care — Convertible Models Only Use a mild detergent to clean the top. Avoid heavy scrubbing and rinse with plenty of clean water. Allow to dry thoroughly before storage. Interior Care Use MOPAR Total Clean to clean fabric upholstery and carpeting.
Page 231 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 232: Fuses
230 MAINTAINING YOUR VEHICLE FUSES Power Distribution Center The Power Distribution Center is located in the engine compartment on the driver’s side of the vehicle. This center contains fuses and relays. Power Distribution Center Cavity Car- Mini- Description tridge Fuse Fuse 40 Amp —...
Page 233 Cavity Car- Mini- Description tridge Fuse Fuse 40 Amp — Headlights Green 30 Amp — Ignition Switch Run Feed Pink — 20 Amp Auto Shutdown Relay Yellow (ASD) — 20 Amp Cigar Lighter Yellow — 15 Amp Hazard Flasher Blue —...
Page 234 232 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description tridge Fuse Fuse 64, 65 — 10 Amp Airbag 66, 67 — 20 Amp WIPER Switch Yellow 68, 69 — 20 Amp Left HID Headlight Yellow 70, 71 — 20 Amp Right HID Headlight Yellow CAUTION! When installing the Power Distribution Center...
Page 235: Mini-Power Distribution Center
Mini-Power Distribution Center The Mini-Power Distribution Center is located in the engine compartment on the passenger’s side of the vehicle. This center contains radiator fan control relays and has two externally-mounted 40 Amp fuses for the radiator fans. Mini-Power Distribution Center MAINTAINING YOUR VEHICLE 233 CAUTION! When installing the Mini-Power Distribution...
Page 236: Vehicle Storage
234 MAINTAINING YOUR VEHICLE VEHICLE STORAGE We recommend that you follow these guidelines for storing your vehicle for extended periods. Fill the fuel tank. This will prevent water condensation inside the tank. If you plan to store your vehicle more than two months, add an anti-oxidant fuel stabilizer to the fuel tank.
Page 237 Then, either disconnect the battery at the negative terminal or use the “Battery Save Feature” to conserve battery power. Refer to “Battery Save Feature” under “Maintenance Procedures” in this section for details. NOTE: Disconnecting the battery causes the engine control system to lose memory of some “learned” func- tions.
Page 238: Replacement Bulbs
236 MAINTAINING YOUR VEHICLE properly. If not, there is a problem with a switch or the system. See your authorized dealer for service. Cover the vehicle whenever possible to prevent acci- dental damage to the finish. REPLACEMENT BULBS LIGHT BULBS — Interior Message Center Indicators .
Page 239: Bulb Replacement
LIGHT BULBS — Exterior (Coupe Models) Low/High Beam High Intensity Discharge (HID) Headlight ..Serviced at authorized dealer only Auxiliary High Beam Headlight ..(HB3A) 9005XS Front Park/Turn Signal Light ... . . 3157AK Fog Light .
Page 240: High Intensity Discharge Headlights (Hid)
238 MAINTAINING YOUR VEHICLE 2. Turn the appropriate bulb and socket assembly counter- clockwise, and then pull it out of the headlight assembly. 1 — Front Side Marker Light 2 — Front Park/Turn Signal Light 3 — Low/High Beam HID Headlight 4 —...
Page 241: Front Fog Light
WARNING! A transient high tension occurs at the bulb sockets of High Intensity Discharge (HID) headlights when the HEADLIGHT switch is turned ON. It may cause serious electrical shock or electrocution if not ser- viced properly. See your authorized dealer for ser- vice.
Page 242: Taillight, Tail/Stop Light, Rear Marker Light
240 MAINTAINING YOUR VEHICLE 2. Turn the bulb and socket assembly counterclockwise, and then pull it out of the front fog light assembly. 3. Pull the bulb out of the socket assembly. 4. Push the replacement bulb into the socket assembly. 5.
Page 243: Taillight, Tail/Stop Light, Rear Marker Light (Coupe Models)
3. Turn the appropriate bulb and socket assembly coun- terclockwise, and then pull it out of the upper light assembly. 1 — Rear Marker Light 2 — Tail/Stop Light 3 — Taillight MAINTAINING YOUR VEHICLE 241 4. Pull the bulb out of the socket assembly. 5.
Page 244: Backup Light, Rear Turn Signal Light
242 MAINTAINING YOUR VEHICLE Backup Light, Rear Turn Signal Light 3. Remove the three upper light assembly retaining nuts. 1. Open the trunk. 2. Remove the two fasteners and then remove the access panel.
Page 245 MAINTAINING YOUR VEHICLE 243 5. Remove the upper light assembly. 4. Remove the three bulb and socket assemblies from the upper light assembly by turning them counterclockwise and then pulling them out of the upper light assembly.
Page 246: Rear Turn Signal Light
244 MAINTAINING YOUR VEHICLE 6. Turn the appropriate bulb and socket assembly coun- terclockwise, and then pull it out of the lower light assembly. 1 — Backup Light 2 — Rear Turn Signal Light 7. Pull the bulb out of the socket assembly. 8.
Page 247: License Light
10. Reinstall the three bulb and socket assemblies into the upper light assembly, and turn them clockwise. 11. Reinstall the upper light assembly and the three retaining nuts. 12. Install the access panel and the two fasteners. 13. Close the trunk. License Light 1.
Page 248: Fluids And Capacities
246 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil with Filter 8.4 Liter Engine (SAE 0W-40, API Certified) Cooling System * 8.4 Liter Engine (MOPAR Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S.
Page 249: Fluids, Lubricants, And Genuine Parts
FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or SM/CF, and meet the requirements of Chrysler Material Standard MS-10725.
Page 250: Chassis
248 MAINTAINING YOUR VEHICLE Chassis Component Transmission Rear Axle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid MOPAR Synthetic Gear and Axle Lubricant SAE 75W-140 or equivalent, with Limited Slip Additive Friction Modifier MOPAR Brake and Clutch Fluid DOT 4 Motor Vehicle or equivalent MOPAR Power Steering Fluid + 4, MOPAR ATF+4 Automatic Transmission Fluid...
Page 251 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..250 Maintenance Schedules ....250 Maintenance Schedule B ....253 Maintenance Schedule A .
Page 252: Emissions Control System Maintenance
250 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability.
Page 253 NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5000 km) or three months, whichever comes first, and follow the maintenance recommendations in “Maintenance Schedule B” in this section. If ANY of these apply to you, then flush and replace the engine coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first, and follow the maintenance...
Page 254 252 MAINTENANCE SCHEDULES At Each Stop for Fuel Check the engine oil level about five minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark.
Page 255: Maintenance Schedule B
MAINTENANCE SCHEDULE B Follow “Maintenance Schedule B” if you usually operate your vehicle under one or more of the following condi- tions. Day or night temperatures are below 32°F (0°C). Stop and go driving. Extensive engine idling. Driving in dusty conditions. Short trips of less than 10 miles (16 km).
Page 256 254 MAINTENANCE SCHEDULES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if nec- essary. Inspect the transmission fluid. Inspect the brake linings. Change the rear axle fluid. Change the brake fluid.
Page 257 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if nec- essary. Inspect and replace the PCV valve, if neces- sary. Change the transmission fluid. Inspect the transmission fluid.
Page 258 256 MAINTENANCE SCHEDULES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the engine air cleaner fil- ter, if necessary. Inspect and replace the auto tension drive belt, if necessary.
Page 259 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if necessary. Inspect and replace the PCV valve, if necessary. Flush and replace engine coolant at 60 months, if not done at 102,000 miles.
Page 260 258 MAINTENANCE SCHEDULES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the air cleaner filter, if nec- essary. Inspect and replace the PCV valve, if neces- sary. Inspect and replace the auto tension drive belt, if necessary.‡...
Page 261 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Replace the spark plugs. Replace the ignition cables. Flush and replace the engine coolant, if not replaced at 60 months.
Page 262 260 MAINTENANCE SCHEDULES Miles (Kilometers) Change the rear axle fluid. Change the brake and clutch fluid. Change the brake fluid. Lubricate the front and rear suspension ball joints. 93,000 96,000 99,000 102,000 (155 000) (160 000) (165 000) (170 000) (175 000) (180 000) 105,000 108,000...
Page 263 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Inspect and replace the engine air cleaner filter, if neces- sary. Inspect and replace the PCV valve, if necessary. Flush and replace the engine coolant, if not replaced at 102,000 months.
Page 264 262 MAINTENANCE SCHEDULES Miles (Kilometers) Change the rear axle fluid. Change the brake and clutch fluid. Lubricate the front and rear suspension ball joints. ‡ This maintenance is not required if previously replaced. Although not required, the manufacturer recom- mends reprogramming TPMS after rotating tires so sys- tem can relearn tire pressure sensor location.
Page 265: Maintenance Schedule A
MAINTENANCE SCHEDULE A Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Inspect the transmission fluid. Inspect the brake linings. Change the rear axle fluid. Change the brake fluid. Lubricate the front and rear suspension ball joints.
Page 266 264 MAINTENANCE SCHEDULES Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Inspect and replace the PCV valve, if necessary. Flush and replace the engine coolant at 60 months, if not done at 102,000 miles.
Page 267 Miles (Kilometers) [Months] Change the rear axle fluid. Change the brake and clutch fluid. Change the brake fluid. Lubricate the front and rear suspension ball joints. MAINTENANCE SCHEDULES 265 36,000 42,000 48,000 (60 000) (70 000) (80 000) [36] [42] [48] 54,000 60,000...
Page 268 266 MAINTENANCE SCHEDULES Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Inspect and replace the PCV valve, if necessary. Inspect and replace the auto tension drive belt, if necessary.‡...
Page 269 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate the tires. Inspect and replace the engine air cleaner filter, if necessary. Inspect and replace the PCV valve, if necessary. Replace the spark plugs. Replace the ignition cables. Flush and replace the engine coolant, if not re- placed at 60 months.
Page 270 268 MAINTENANCE SCHEDULES Miles (Kilometers) [Months] Inspect the brake linings. Change the rear axle fluid. Change the brake and clutch fluid. Lubricate the front and rear suspension ball joints. ‡ This maintenance is not required if previously replaced. Although not required, the manufacturer recom- mends reprogramming TPMS after rotating tires so sys- tem can relearn tire pressure sensor location.
Page 271 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle......271 Prepare For The Appointment .
Page 272 270 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Quality Grades ......276 Treadwear ......277 Traction Grades .
Page 273: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 274: Chrysler Llc Customer Center
272 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Page 275: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 276: Warranty Information (U.s. Vehicles Only)
274 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addi- tion, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemi- cals known to the State of California to cause cancer and birth defects, or other reproductive harm.
Page 277: In Canada
To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administra- tor, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Page 278: Department Of Transportation Uniform Tire Quality Grades
276 IF YOU NEED CONSUMER ASSISTANCE Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 279: Treadwear
Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
Page 280 278 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
Page 281 INDEX...
Page 282 280 INDEX About Your Brakes ..... . . 147 ABS (Anti-Lock Brake System) ... . 101,148 Accessory Delay, Power .
Page 283 Location ......192,207 Saving Feature (Protection) ....210 Storing Vehicle .
Page 284 282 INDEX Clean Air Gasoline ..... . . 171 Climate Control ......125 Clock .
Page 285 Door Locks ......25 Door Locks, Automatic ....27 Doors .
Page 286 284 INDEX Engine Oil Viscosity Chart ....205 Ethanol ....... 171 Exhaust Gas Caution .
Page 287 Gauge ......109 Methanol ......171 Octane Rating .
Page 288 286 INDEX Hood Release ......81 Hydraulic Clutch Fluid ....224 Ignition .
Page 289 Battery Saver ......84,88 Brake Warning ......104 Bulb Replacement .
Page 290 288 INDEX Power Door ......26 Low Tire Indicator ..... . . 169 Low Tire Pressure System .
Page 291 Checking ......203 Dipstick ......203 Disposal .
Page 292 290 INDEX Radial Ply Tires ......163 Radiator Cap (Coolant Pressure Cap) ..219 Radio Antenna .
Page 293 Seat Belt Reminder ..... 39,107 Seat Belts ......33,34 And Pregnant Women .
Page 294 292 INDEX Steering Power ......144 Tilt Column ......91 Storage .
Page 295 Tread Wear Indicators ....164 Top Cover ......69 Towing .
Page 296 294 INDEX Warranty Information ..... 274 Washer, Adding Fluid ..... 213 Washers, Windshield .
Page 297 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalKey-In-Ignition ReminderVEHICLE SECURITY ALARM SYSTEM Rearming of the SystemTo Arm the SystemTo Disarm the SystemElectronic Immobilization System - Canada OnlyILLUMINATED ENTRY SYSTEM REMOTE KEYLESS ENTRY (RKE) To Unlock the DoorsTo Lock the DoorsTo Unlatch the Trunk/LiftgateUsing The Panic AlarmProgramming Additional TransmittersBattery ReplacementGeneral InformationDOOR LOCKS Manual Door LockPower Door LocksWINDOWS Power WindowsAuto Down Feature Wind BuffetingLIFTGATE - COUPE MODELS ONLY TRUNK LOCK AND RELEASE - CONVERTIBLE MODELS ONLY TRUNK SAFETY WARNING - CONVERTIBLE MODELS ONLY Trunk Emergency ReleaseOCCUPANT RESTRAINTS Lap/Shoulder BeltsLap/Shoulder Belt Untwisting ProcedureEnhanced Seat Belt Reminder System (BeltAlert) Automatic Locking ModeSeat Belts and Pregnant WomenSeat Belt ExtenderDriver and Passenger Supplemental Restraint System (SRS) - AirbagChild RestraintBREAK-IN RECOMMENDATIONS...
Page 298: Installation Of Radio Transmitting Equipment
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.

Dodge 2009 Viper Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Replacement Bulbs/Bulb Number

Maintenance Schedules

If You Need Consumer Assistance

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dodge 2009 Viper

Summary of Contents for Dodge 2009 Viper