Page 1 2009 OWNER’S MANUAL...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 7 INTRODUCTION 5...
Page 8: Van Conversions/Campers
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Identification Number
VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove the VIN.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With A Key .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry (RKE) — If Equipped . . . 20 To Unlock The Doors ....21 To Lock The Doors .
Page 13 Driver And Right Front Passenger Supplemental Restraint System (SRS) — Airbags ......47 Event Data Recorder (EDR) .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
Page 15 NOTE: • If you try to remove the key before you place the shift lever in PARK, the key may become trapped tempo- rarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 16: Locking Doors With A Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With A Key You can insert the key with either side up. To lock the door, turn the key rearward. To unlock the door, turn the key forward. For door lock lubrication, see “Body Lubri- cation”...
Page 17: Sentry Key
SENTRY KEY The Sentry Key Immobilizer System prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speedpass™, additional Sentry Keys , or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle.
Page 19: Customer Key Programming
Customer Key Programming If you have two valid Sentry Keys , you can program new Sentry Keys to the system by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2.
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE reprogrammed. All vehicle keys must be taken to an authorized dealer at the time of service to be reprogrammed. General Information The Sentry Key system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: •...
Page 21: To Disarm The System
Vehicle Security Alarm is arming. The Vehicle Security Light in the instrument panel cluster will flash rapidly for about 16 seconds to indicate that the alarm is being set. After the alarm is set, the Vehicle Security Light will flash at a slower rate to indicate that the Vehicle Security Alarm is armed.
Page 22: Illuminated Entry System - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM — IF EQUIPPED The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open the doors. This feature is only available if you have Remote Keyless Entry.
Page 23: To Unlock The Doors
To Unlock the Doors Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and, if installed, the cargo lamp will turn on for 30 seconds.
Page 24: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Continue to hold the LOCK button, wait at least four seconds, but no longer than 10 seconds, then press and hold the PANIC button. Release both buttons at the same time. 4.
Page 25: Programming Additional Rke Transmitters
Programming Additional RKE Transmitters Refer to “Sentry Key Programming” under “Sentry Key ” in this section. If you do not have a programmed RKE transmitter, contact your authorized dealer for details. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada.
Page 26: Rke Transmitter Battery Service
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE RKE Transmitter Battery Service 1. With RKE transmitter buttons facing down, use a flat blade or dime to pry the two halves of the RKE transmit- ter apart. Make sure not to damage the rubber gasket during removal.
Page 27: Remote Starting System - If Equipped
REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system has a targeted range of 328 ft (100 m). NOTE: The vehicle must be equipped with an auto- matic transmission to be equipped with Remote Start.
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The engine can be started two consecutive times (two 15-minute cycles) with the RKE transmitter. However, the ignition switch must be cycled to the ON position before you can repeat the start sequence for a third cycle.
Page 29: Door Locks
DOOR LOCKS Manual Door Locks Front and rear doors may be locked by moving the lock plunger up or down. All doors may be opened with the inside door handle without lifting the lock plunger. Doors locked before closing will remain locked when closed. The ignition key will unlock all the locks on your vehicle.
Page 30: Power Door Locks - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch Location If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate.
Page 31 3. Place the key into the ignition. 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times, ending in the ON/RUN position. (Do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction.
Page 32: Child Protection Door Lock
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times, ending in the ON/RUN position. (Do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction.
Page 33 To use the system, open each rear door, slide the lever UP to engage the locks and DOWN to disengage the child protection door locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even, if the inside door LOCK is in the UNLOCKED position.
Page 34: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows—If Equipped Power Window Switches The control on the left front door panel has Up/Down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab and Mega Cab models.
Page 35: Wind Buffeting
Auto-Down (Driver’s Side Only) The driver’s window switch has an Auto-Down feature. Press the window switch past the detent, release, and the window will automatically go down. Window Lockout Switch (4–Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Page 36: Occupant Restraints
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and if equipped, window bags for the driver and passengers...
Page 37: Lap/Shoulder Belts
Lap/Shoulder Belts All seating positions except the Quad Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.
Page 39 3. When the belt is extended long enough to fit, insert the latch plate into the buckle until you hear a “click.” Inserting Latch Plate into Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! • A belt buckled into the wrong buckle will not protect you properly.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury.
Page 41 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Regular Cab Front Center Three-Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
Page 43 WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 44: Adjustable Upper Shoulder Belt Anchorage
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In-Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 45: Automatic Locking Retractors (Alr) Mode - If Equipped
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 46: Center Lap Belts
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Center Lap Belts The center seating position for the Quad Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a click. To lengthen the lap belt, tilt the latch plate and pull.
Page 47: Enhanced Seat Belt Use Reminder System (Beltalert )
Enhanced Seat Belt Use Reminder System (BeltAlert ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Seat Belt Use Reminder System (BeltAlert ) will alert the driver to buckle the seat belt.
Page 48: Seat Belts And Pregnant Women
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. BeltAlert can be reactivated by repeating this procedure. NOTE: Although BeltAlert has been deactivated, the Seat Belt Reminder Light will continue to illuminate while the driver’s seat belt remains unbuckled.
Page 49: Driver And Right Front Passenger Supplemental Restraint System (Srs) - Airbags
Driver And Right Front Passenger Supplemental Restraint System (SRS) — Airbags 1 — Driver and Passenger Airbags 2 — Knee Bolsters This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
Page 51 The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate-to- severe frontal collisions. If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate-to- severe side collisions.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child restraints or belt-positioning booster seats, should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. 4. All occupants should use their lap and shoulder belts properly.
Page 53 Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • Side Remote Acceleration Sensors (if equipped) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Window Bags above Side Windows (if equipped) •...
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate.
Page 55 Only). See Passenger Airbag ON/OFF Switch – (2500/ 3500 Regular Cab Vehicles Only) in this section for additional information. Passenger Airbag Disable (PAD) Indicator Light • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the window bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of non-toxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window.
Page 57 The passenger front airbag is to be turned off only if the passenger: • is an infant (less than one year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant;...
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag (2500/3500 Regular Cab Vehicles Only) Place the ignition key in the Passenger Airbag ON/OFF Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn ON the passenger airbag.
Page 59 irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufac- turer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you.
Page 60: Event Data Recorder (Edr)
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material – special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately five seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
Page 61 ment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable. NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indica- tive of a crash, but not severe enough to warrant airbag deployment.
Page 62: Child Restraints
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Used in defense of litigation involving a Chrysler LLC product. 3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that may be recorded: • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system •...
Page 63 Children 12 years and younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. WARNING! Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag unless the airbag is turned off.
Page 65 WARNING! (Continued) • A rearward-facing child restraint should only be used in a rear seat, or in the front seat if the passenger’s front airbag is OFF. If the airbag is left ON, a rearward-facing child restraint in the front seat may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. •...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the front seat of a Regular Cab model, refer to the “Passenger Airbag ON/OFF Switch”...
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab Rear Seats Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage, have been available for some time.
Page 69 inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. • If your child restraint seat is not LATCH-compatible, install the restraint using the vehicle seat belt. Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 71 Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seatback under the head restraint to the tether anchor directly behind the seat.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up”...
Page 73 Multiple Child Restraints 1 — Inner Anchor Strap Ring(s) 2 — Snap Hook 3 — Tether Strap 4 — Passenger’s Side Rear Child Seat 5 — Rear Center Child Seat 6 — Driver’s Side Rear Child Seat THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Tether Anchorage Points at All Three Seating Positions (Mega Cab ) 1.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. Mega Cab Tether Anchor 1 — Tether Strap Hook 2 — Tether Strap to Child Restraint 3 —...
Page 75: Engine Break-In Recommendations
Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.
Page 76: Safety Tips
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed.
Page 77: Safety Checks You Should Make Inside The Vehicle
If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Page 78: Periodic Safety Checks You Should Make Outside The Vehicle
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable.
Page 79 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......82 Inside Day/Night Mirror .
Page 80 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition (VR) System — If Equipped ......114 Voice Recognition (VR) System Operation Commands .
Page 81 Windshield Wipers And Washers Intermittent Wiper System ... . . 138 Windshield Washers ....139 Tilt Steering Column .
Page 82 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Compass Calibration Manual Compass Calibration Recalibrating The Compass Outside Temperature ....153 Garage Door Opener — If Equipped Programming HomeLink Gate Operator/Canadian Programming Using HomeLink...
Page 83 Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission ..... . . 165 Front Instrument Panel Cupholders (Bucket Seats) ..... . . 166 Rear Cupholder (Quad Cab ) —...
Page 84: Mirrors
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
Page 85: Outside Mirrors
Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight...
Page 86: Outside Mirrors Folding Feature
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Folding Feature All 6 x 9 in exterior mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward and normal.
Page 87: Heated Mirrors - If Equipped
Power Mirror Movement Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this section, for further information. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Trailer Towing Mirrors —...
Page 88: Uconnect Phone - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is integrated onto the main mirror surface. Blindspot Mirror uconnect phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect phone.
Page 89 For uconnect customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 uconnect allows you to transfer calls between the sys- tem and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation.
Page 90: Operation
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The uconnect phone can be used with any Hands-Free Profile certified Bluetooth cellular phone. See the uconnect website for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile) you may not be able to use any uconnect features.
Page 91 example, you can use the combined form voice com- mand Phonebook New Entry, or you can break the combined form command into two voice commands: Phonebook and New Entry. Please remember, the uconnect phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, after the beep, say Pair a Phone and follow the audible prompts. • You will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your cellular phone.
Page 93 Call by Saying a Name • Press the PHONE button to begin. • After the Ready prompt and the following beep, say “Call. • The system will prompt you to say the name of the person you want to call. •...
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The uconnect phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
Page 95 • Only the cellular phone’s phonebook is downloaded. SIM card phonebook is not part of the Mobile phone- book. • This downloaded phonebook cannot be edited or deleted on the uconnect phone. These can only be edited on the cellular phone. The changes are trans- ferred and updated to uconnect phone on the next phone connection.
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit uconnect Phonebook Entries NOTE: • Editing names in the phonebook is recommended when the vehicle is not in motion. • Automatic downloaded phonebook entries cannot be deleted or edited. • Press the PHONE button to begin. •...
Page 97 • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say List Names to hear a list of the entries in the phonebook from which you choose.
Page 98: Phone Call Features
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the uconnect Phonebook • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Phonebook List Names. • The uconnect phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available.
Page 99 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cellular phone.
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on hold), press and hold the PHONE button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 101: Uconnect Phone Features
Call Continuation Call continuation is the progression of a phone call on the uconnect phone after the vehicle ignition key has been switched to OFF. Call continuation functionality avail- able on the vehicle can be any one of three types: •...
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance If you are in an emergency and the cellular phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the uconnect phone is operational, you may reach the emergency number as follows: •...
Page 103 Towing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Towing Assistance. NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico).
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your uconnect phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the VOICE RECOGNITION button and say the sequence you wish to enter, followed by the word Send.
Page 105 Turning Confirmation Prompts ON/OFF Turning confirmation prompts off will stop the system from confirming your choices (e.g., the uconnect phone will not repeat a phone number before you dial it). • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Setup Confirmations.
Page 106: Advanced Phone Connectivity
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute OFF) When you mute the uconnect phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect phone: •...
Page 107 • The uconnect phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the VOICE RECOGNITION button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select”...
Page 108: Things You Should Know About Your Uconnect Phone
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your uconnect phone uconnect phone Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “uconnect Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the uconnect phone Voice Training feature may be used.
Page 109 • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: •...
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and •...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109...
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 115 Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
Page 116: General Information
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 117 When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options.
Page 118: Commands
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition (VR) system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2.
Page 119 Radio FM To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the frequency) • “Next Station” (to select the next station) • “Previous Station” (to select the previous station) •...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording, you may press the VR button to stop recording.
Page 121: Voice Training
NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, uconnect phone Voice Training feature may be used.
Page 122: Manual Seat Adjuster - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Adjuster — If Equipped The front seats are adjustable, forward or rearward. The adjustment handle is located at the front edge of each seat cushion. Pull upward on the handle and slide the seat, forward or rearward, to the desired position.
Page 123: Reclining Seats (Quad Cab Models)
Reclining Seats (Quad Cab Models) The recliner handle is located on the outside of the seat cushion. Pull upward on the handle to release the seat- back, lean forward or rearward to the desired position. Seat Recliner Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined.
Page 124: Reclining Seats (2500/3500 Models)
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats (2500/3500 Models) The recliner handle is located on the outside of the seat cushion. Pull upward on the handle to release the seat- back, lean forward or rearward to the desired position. Seat Recliner Handle WARNING! You can be seriously, even fatally, injured riding in a...
Page 125: Adjustable Head Restraints
Adjustable Head Restraints Head restraints can reduce the risk of neck injury in the event of a rear impact. To adjust, pull upward on the head restraints so that the upper edge is as high as practical, at least to the level of the ears. To lower the head restraint, push inward on the button and push down on the head restraint.
Page 126: Power Seats - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped The power seat controls are located on the outboard side of the front seat cushions. Three switches control the seat movement. Power Seat Switch The four-way switch is used to move the seat cushion forward or backward, or to adjust the seat height up or down.
Page 127: Rear Seat Features
Tilt Adjustment CAUTION! Do not place anything under a power seat. It may cause damage to the seat or the seat controls. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Rear Seat Features Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Table Mode) — If Equipped Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint. Table Mode Handle 2.
Page 129 Folding Rear Seat (Kneel Mode) — If Equipped Both the left and right rear seats can be folded flat (kneel mode) and used for carrying cargo. Each of the rear seatbacks provide two D-rings and rear storage bin lids with two slotted cutouts. Use a cargo tie-downs to secure cargo.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The rear seat will drop and move forward in “kneel mode”. To fold either rear seat flat: 1. Lift the handle, located on the outboard side of the seat. Kneel Mode Handle 2.
Page 131: Heated Seats - If Equipped
WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Heated Seats —...
Page 132: To Open And Close The Hood
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex- haustion or other physical condition must exercise...
Page 133 2. Reach into the opening beneath the center of the grille and push upward on the safety latch to release it before raising the hood. Safety Latch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 CAUTION! To prevent possible damage, do not slam the hood to close it.
Page 134: Lights
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS The headlight switch is located on instrument panel to the left of the steering wheel. Headlight Switch Location Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or by pressing the UNLOCK button on the Remote Keyless Entry (RKE) transmitter (if...
Page 135: Battery Saver
Dimmer Control Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar, or if the dimmer control is rotated upwards for approximately 10 minutes, the interior lights will automatically turn off.
Page 136: Headlights, Parking Lights And Panel Lights
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights and Panel Lights When the headlight switch is rotated to the first position, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on. The headlights will turn on when the switch is rotated to the second position.
Page 137: Lights-On Reminder
DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate. Lights-on Reminder If the headlights, parking lights or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened.
Page 138: Multifunction Lever
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever, located on the left side of the steering column, is used to activate the turn signals and high beams headlights. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Lane Change Assist Tap the lever up or down once and the turn signal (left or right) will flash three times then automatically turn off. Flash-to-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel.
Page 140: Windshield Wipers And Washers
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed. Windshield Wiper/Washer Switch Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 141: Windshield Washers
WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 142: Tilt Steering Column
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt control lever is located on the left-side of the steering column, just below the multifunction lever. Pull the lever toward the steering wheel to unlock the steering column.
Page 143: Driver Adjustable Pedals - If Equipped
DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The adjustable accelerator and brake pedal allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustable Pedals Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag, located in the center of the steering wheel.
Page 144: Electronic Speed Control - If Equipped
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.
Page 145: To Activate
simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE”...
Page 146: To Accelerate For Passing
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE is tapped, speed increases so that tapping the button three times will increase speed by 3 mph (4.8 km/h). Tapping the SET DECEL button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases.
Page 147: Overhead Console - If Equipped
OVERHEAD CONSOLE — IF EQUIPPED The two optional overhead consoles may consist of the following features: Overhead Console Features • Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC) — If Equipped UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
Page 148: Overhead Console With Compass/Temperature Mini-Trip Computer - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WITH COMPASS/ TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC) Courtesy Lights This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored.
Page 149: Us/M Button
US/M Button Use this button to change the display from U.S. to METRIC measurement units. US/M Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Reset Button Use this button to reset the following displays: • Average Fuel Economy (AVG ECO) •...
Page 150: Global Reset
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Global Reset If the RESET button is pressed twice within two seconds while in any of the four displays (AVG, ECO, ODO, ET), the Global Reset will reset all four displays. Step Button Use this button to choose or cycle through the four trip conditions.
Page 151: Distance To Empty (Dte)
When the fuel economy is reset, the display will momen- tarily blank. Then, the history will be erased, and the AVERAGING WILL CONTINUE FROM WHERE IT WAS BEFORE THE RESET. The reset value is based on a minimal amount of fuel used and the distance traveled from the previous drive cycle.
Page 152: Trip Odometer (Odo)
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trip Odometer (ODO) NOTE: maximum value 6000 miles (9956 km). Then the trip odometer must be reset in order to update the trip odometer miles/ kilometers. This display shows the distance traveled since the last reset.
Page 153: Understanding The Features Of Your Vehicle 151
WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Automatic Compass Calibration This compass is self-calibrating which eliminates the need to manually set the compass.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Magnetic materials should be kept away from the overhead console. This is where the compass sensor is located. RESET Button Compass Variance is the difference between magnetic North and geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 155: Outside Temperature
RESET button approximately five seconds. The last vari- ance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. Outside Temperature Because the ambient temperature sensor is located under the hood, engine temperature can influence the displayed temperature, therefore, temperature readings are slowly updated when the vehicle speed is below 20 mph...
Page 156: Programming Homelink
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse”...
Page 157 Your vehicle should be parked outside of the garage while training. 1. Turn the ignition switch to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) from the HomeLink buttons while keeping the HomeLink display in view.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).
Page 159: Gate Operator/Canadian Programming
7. Return to the vehicle and press the programmed HomeLink button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training.
Page 160: Using Homelink
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) The hand-held transmitter of the device may also be used at any time.
Page 161: General Information
• Did you unplug the device for training and remember to plug it back in? If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com, for information or assistance. General Information This device complies with FCC rules part 15 and Industry Canada RSS-210.
Page 162: Open Sunroof - Express Mode
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
Page 163: Pinch Protect Override
sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs.
Page 164: Sunroof Maintenance
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS The auxiliary electrical power outlet can provide power for in-cab accessories designed for use with the standard...
Page 165 There is also a power outlet located on the rear of the center console (if equipped with bucket seats). Rear Power Outlet The power outlet(s) has/have a fused direct feed from the battery so it/they receive power whether the ignition is ON or OFF.
Page 166: Cigar Lighter And Ash Receiver
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
Page 167: Cupholders
Ash Receiver CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission Located in the front center stack of the instrument panel are two adjustable cupholders. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 To access the cupholders pull on the cupholder door handle located on the instrument panel.
Page 168: Front Instrument Panel Cupholders (Bucket Seats)
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. Cupholders Front Instrument Panel Cupholders (Bucket Seats) If your vehicle is equipped with bucket seats there are three cupholders located on the front of the center...
Page 169: Rear Cupholder (Quad Cab ) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Rear Cupholder (Quad Cab ) — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. STORAGE Center Storage Compartment (40–20–40 Seat) – If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid.
Page 170 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. •...
Page 171: Center Storage Compartment (Bucket Seats) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Center Storage Compartment (Bucket Seats) – If Equipped Push the upper button on the front of the armrest to raise the upper cover. Inside is a power outlet (if equipped), a cutout for a cellular phone charger cord, removable coin holder (if equipped), and a divider to configure the storage area into separate compartments.
Page 172 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. •...
Page 173: Storage And Seats (Quad Cab Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Storage and Seats (Quad Cab Models) Located in the center of the front 40–20–40 seat cushion there is a storage compartment. Regular Cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat.
Page 174: Plastic Grocery Bag Retainers - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic Grocery Bag Retainers — If Equipped Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Grocery Bag Hooks REAR WINDOW FEATURES Rear Window Defroster and Heated Outside Mirrors —...
Page 175: Power Sliding Rear Window - If Equipped
CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
Page 176: Sliding Rear Window - If Equipped
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat may be equipped with a folding load floor.
Page 177 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Positioning the Load Floor for Storage Access Under the Seat 1.
Page 178: Pickup Box
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Load Floor Securing Straps 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. PICKUP BOX The pickup box has many features designed for utility and convenience.
Page 179 NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar available from your authorized dealer. You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
Page 180: Slide-In Campers
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box.
Page 181 Tailgate Support Strap Attachment 3. Raise the right side of the tailgate until the right side pivot clears the hanger bracket. 4. Slide the entire tailgate to the right to free the left side pivot. 5. Remove the tailgate from the vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: •...
Page 183: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....184 Ram Truck ......184 Power Wagon .
Page 184 182 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode For MP3 Audio Play) ......214 Load/Eject Button (CD Mode For MP3 Play) .
Page 185 Using The PTY (Program Type) Button — If Equipped ......229 PTY Button Scan ....230 PTY Button Seek .
Page 186: Instrument Panel Features
184 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES RAM TRUCK 1 — Headlight Switch 6 — Passenger Airbag 2 — Air Outlets 7 — Glove Compartment 3 — Instrument Cluster 8 — Passenger Airbag On/Off Switch* 4 — Climate Controls 9 —...
Page 187: Power Wagon
POWER WAGON 1 — Headlight Switch 6 — Passenger Airbag* 2 — Air Outlets 7 — Glove Compartment 3 — Instrument Cluster 8 — Power Outlet 4 — Climate Controls 9 — Heated Seat Switch 5 — Radio 10 — TPMS “Light Load” Reset Switch* * If Equipped UNDERSTANDING YOUR INSTRUMENT PANEL 185 11 —...
Page 188: Instrument Cluster - Base
186 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – BASE...
Page 189: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 187 INSTRUMENT CLUSTER – PREMIUM...
Page 190: Instrument Cluster Description
188 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Check Gauges – Premium Cluster Only This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gauges indicate a reading either too high or too low. Examine the gauges carefully, and follow the instructions contained below for each indicated problem.
Page 191 continuous chime will sound to alert you to turn the signals off. If either indicator flashes at a rapid rate, check for a defective outside light bulb. 4. Tachometer The Tachometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high RPM for extended periods.
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Oil Pressure Gauge — Premium Cluster Only The pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction. Immedi- ate service should be obtained from an authorized dealer.
Page 193 CAUTION! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”...
Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Shift Lever Indicator (Automatic Transmission Only) This display indicator shows the automatic transmission shift lever selection. NOTE: You must apply the brakes before shifting from PARK. 16. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven.
Page 195 engine. With the odometer value displayed, hold the trip button down for a period of six seconds. The odometer will change to trip value first, then it will display the engine hour value. The engine hours will be displayed for a period of 30 seconds until the ignition is turned OFF or the engine is started.
Page 196: Understanding Your Instrument Panel 181
194 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD II, that monitors engine and automatic transmission con- trol systems. The light will illuminate when the key is in the ON position, before engine start.
Page 197 The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 20.
Page 199 22. Cargo Light The Cargo Lamp light will illuminate when the Cargo Lamp is activated by pressing the Cargo Light Button on the headlight switch. 23. SERV 4WD Indicator The 4WD indicator will be illuminated when- ever the 4WD mode is engaged for either the manual or electric shift 4WD systems.
Page 200 198 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated.
Page 201 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
Page 202 200 UNDERSTANDING YOUR INSTRUMENT PANEL 29. Fuel Gauge Shows level of fuel in tank when ignition switch is in the ON position. 30. Low Fuel Light When the fuel level drops to 1/16 tank, the fuel symbol will light and a single chime will sound. NOTE: If your vehicle is equipped with an overhead console module (CMTC), it is possible for DTE to display “LO FUEL”...
Page 203: Electronic Digital Clock
33. Charging System Light This light shows the status of the electrical charg- ing system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
Page 204: Clock Setting Procedure
202 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes.
Page 205: Operating Instructions - Radio Mode
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOL control to turn the radio ON. Push the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL will return. Rotating the volume control, turning the radio ON/OFF, or turning OFF the ignition will also return the sound from the speakers NOTE: In Hands Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if...
Page 207 RW/FF (Radio Mode) Pressing the Rewind/Fast Forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary TUNE control clockwise to increase or counter-clockwise to decrease the channel number.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Program Type Radio Mode) Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button or turning the TUNE rotary knob within 5 seconds will allow the program format type to be selected.
Page 209 16 Digit-Character Program Type Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode.
Page 210: Operation Instructions
208 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used a corresponding button number will be displayed. Buttons 1 - 6 (Radio Mode) These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}.
Page 211: Load/Eject Button (Cd Mode For Cd Audio Play)
SEEK Button (CD Mode for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJECT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
Page 213: Notes On Playing Mp3 Files
RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: •...
Page 215 MPEG Sampling Fre- Specification quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 216: Operation Instructions
214 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file.
Page 217 MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the MSG or INFO button once more to return to elapsed time priority mode.
Page 218: (Satellite Radio) And Uconnect Phone
216 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - uconnect studios (Satellite Radio) (If Equipped) Refer to the uconnect studios (Satellite Radio) section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES)™ (If Equipped) Refer to separate Video Entertainment System (VES)™ Guide.
Page 219 Power Switch/Volume Control (Rotary) Push the ON/VOL control to turn the radio ON. Push the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360– degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 220 218 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 221 AM/FM Button (Radio Mode) Press the button to select AM or FM modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control, and “BASS” will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 222: Operating Instructions - Cd Mode
220 UNDERSTANDING YOUR INSTRUMENT PANEL the SET button twice and “SET 2” will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into pushbutton memory.
Page 223 SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD. Press the left side of the button to return to the beginning of the current track, or return to the beginning of the previous track if the CD is within the first 10 seconds of the current selection.
Page 224: Operating Instructions - Auxiliary Mode
222 UNDERSTANDING YOUR INSTRUMENT PANEL RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 225: Operating Instructions - Uconnect Phone - If Equipped
SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for five seconds.
Page 226: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio With Uconnect Gps (Navigation)
224 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH uconnect gps (NAVIGATION) Satellite Navigation Radio and CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability.
Page 227 the worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone and daylight savings information is set. 1. At the Main Menu screen, highlight “Clock Setup” and press ENTER OR press and hold the TIME button on the unit’s faceplate for three seconds.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL User Defined Clock If you wish to set the clock to a time different than the system clock, you can manually adjust the time by choosing the “User Defined Clock” option. 1. At the Clock Setup screen highlight “Displayed Clock: User Defined Clock”.
Page 229: Uconnect Studios (Satellite Radio) - If Equipped
uconnect studios (SATELLITE RADIO) — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios.
Page 230: Selecting Uconnect Studios (Satellite) Mode In Ref, Raq, And Rak Radios
228 UNDERSTANDING YOUR INSTRUMENT PANEL press the SEEK UP button until all 12 ESN/SID digits display. The SEEK DOWN will page down until the first four digits display. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or five minutes have passed since any button was pushed.
Page 231: Selecting A Channel
Selecting Satellite Mode — RAQ and RAK Radio Press the MODE button repeatedly until the word SAT appears in the display. These radios will also display the current station name and program type. For more information, such as song title and artist, press the MSG or INFO button. A CD or tape may remain in the radio while in the Satellite radio mode.
Page 232: Pty Button Scan
230 UNDERSTANDING YOUR INSTRUMENT PANEL PTY Button SCAN When the desired program type is obtained, press the SCAN button within five seconds. The radio will play seven seconds of the selected channel before moving to the next channel of the selected program type. Press the SCAN button a second time to stop the search.
Page 233: Video Entertainment System (Ves)™ - If Equipped
VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF EQUIPPED The optional Video Entertainment System (VES)™ con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The system is located in the headliner behind the front row seat.
Page 234: Radio Operation
232 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker type switch with a button in the center. Pressing the top of the switch will increase the volume, and pressing the bottom of the switch will decrease the volume. The center button of the right-hand control will allow you to change the mode.
Page 235: Radio Operation And Cellular Phones
3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7.
Page 236: Climate Controls
234 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. Climate Control Location Heater Only — If Equipped Manual Heating Controls The mode control (at the right of the control panel) can be set in any of the...
Page 237 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Panel Outside air flows through the outlets located in the instrument panel. Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke or...
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left posi- tion.
Page 239: Air Conditioning And Heating - If Equipped
Air Conditioning and Heating — If Equipped Air Conditioning And Heating UNDERSTANDING YOUR INSTRUMENT PANEL 237 Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the outlets selected by the mode control.
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Page 241 Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel, and the air conditioning may be on. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 242: Air Conditioning With Dual Zone Temperature Control - If Equipped
240 UNDERSTANDING YOUR INSTRUMENT PANEL edges of the instrument panel. The demisters also pro- vide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. To remove frost from the side windows, it is best to use the full defrost mode.
Page 243 A/C Pushbutton With the fan control in the ON posi- tion, pushing the A/C button turns on the air conditioning compressor. An indicator light on the button shows that the Air Conditioning compressor is on. Conditioned air is now directed through the mode outlets selected.
Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air flows through the outlets located in the instru- ment panel and those located on the floor. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets.
Page 245 Dual Zone Temperature Control Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale UNDERSTANDING YOUR INSTRUMENT PANEL 243 indicates cooler temperatures while the red area indicates warmer temperatures.
Page 246: Operating Tips
244 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
Page 247 Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended. For proper coolant type, refer to “Recommended Fluids and Genuine Parts”...
Page 248: Operating Tips Chart
246 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart...
Page 249 STARTING AND OPERATING CONTENTS Starting Procedures ....252 Normal Starting ..... 252 Automatic Transmission .
Page 250 248 STARTING AND OPERATING Electronically Shifted Transfer Case Operating Information/Precautions (Four Position Switch) — If Equipped ..272 Shifting Procedure — Electronically Shifted Transfer Case ..... . . 276 Axle Locker System —...
Page 251 Understanding The Features Of Your Winch ......310 Winch Accessories ....312 Operating Your Winch .
Page 252 250 STARTING AND OPERATING Tire Pressures For High Speed Operation . . . 356 Radial Ply Tires ..... 357 Tire Spinning ..... . . 357 Tread Wear Indicators .
Page 253 Adding Fuel ......379 Loose Fuel Filler Cap (Gas Cap) Message Vehicle Loading ..... 381 Certification Label .
Page 254: Starting Procedures
252 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating.
Page 255 CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle.
Page 256: After Starting
254 STARTING AND OPERATING After Starting The idle speed is automatically controlled and will de- crease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord.
Page 257: Automatic Transmission With Overdrive
WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
Page 258 256 STARTING AND OPERATING WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK.
Page 259 DRIVE This position provides all forward gears, including 3rd gear direct and 4th or 5th gear overdrive (see Overdrive Operation). Use this range for most city and highway driving. SECOND Use this position for driving slowly in heavy city traffic or on mountain roads where more precise speed control is desirable.
Page 260 258 STARTING AND OPERATING • transmission reached temperature. NOTE: • If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for opera- tion at this temperature. Normal operation will re- sume when the transmission fluid temperature has risen to a suitable level.
Page 261 Tow Haul O/D Off Switch This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW HAUL” mode, 5th gear (if equipped) is disabled and 2-3 and 3-4 shift patterns are modified. Shifts into Overdrive (4th gear) are allowed during steady cruise (for improved fuel STARTING AND OPERATING 259 economy) and automatic closed-throttle downshifts to...
Page 262: Four-Wheel Drive Operation - If Equipped
260 STARTING AND OPERATING the upper gears. When the vehicle speed drops or during acceleration when the transmission downshifts to second gear, the clutch automatically disengages. NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usu- ally after 1-3 miles (1.6 - 4.8 km) of driving].
Page 263 This transfer case is intended to be driven in the 2H position for normal street and highway conditions such as dry, hard surfaced roads. When additional traction is required, the 4H and 4L positions can be used to lock the front and rear drive- shafts together and force the front and rear wheels to rotate at the same speed.
Page 264 262 STARTING AND OPERATING NOTE: Delayed shifts out of four-wheel drive may be experienced due to uneven tire wear, low or uneven tire pressures, excessive vehicle loading, or cold tempera- tures. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
Page 265: Shifting Procedure - Manually Shifted Transfer Case
Shifting Procedure - Manually Shifted Transfer Case Manual Transfer Case Shifter 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). With the STARTING AND OPERATING 263 vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera-...
Page 266: Transfer Case Position Indicator Light
264 STARTING AND OPERATING • Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur.
Page 267 This electronically shifted transfer case provides five mode positions. • Two-wheel drive high range (2WD) • Four-wheel drive automatic range (4WD AUTO) • Four-wheel drive lock range (4WD LOCK) • Four-wheel drive low range (4WD LOW) • Neutral (N) This electronically shifted transfer case is designed to be driven in the two–wheel drive position (2WD) or four- wheel drive position (4WD AUTO) for normal street and highway conditions (dry hard surfaced roads).
Page 268 266 STARTING AND OPERATING Driving in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components. NEUTRAL Button NOTE: The transfer case NEUTRAL position is selected by depressing the recessed button located on the lower left hand corner of the 4WD Control Switch.
Page 269 3. When the shift is completed, the “Transfer Case Posi- tion Indicator Light” for the selected position will stop flashing and remain ON. If one or more shift conditions are not met: 1. The “Transfer Case Position Indicator Light” for the current position will remain ON.
Page 270 268 STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD, 4WD AUTO or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h).
Page 271: Shifting Procedure - Electronically Shifted Transfer Case
4WD AUTO Four-Wheel Drive Automatic Range - This range auto- matically engages when the vehicle senses a loss of traction. Additional traction for varying road conditions. 4WD LOCK Four-Wheel Drive Lock Range - This range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed.
Page 272 270 STARTING AND OPERATING • If all the requirements to select a new transfer case position have been met, the current “Transfer Case Position Indicator Light” will turn OFF, the selected “Transfer Case Position Indicator Light” will flash until the transfer case completes the shift. When the shift is completed, “Transfer Case Position Indicator Light”...
Page 273 Alternate Procedure 1. Bring the vehicle to complete stop. 2. With the key ON and the engine either off or running, shift the transmission into NEUTRAL. 3. Rotate the transfer case control switch to the desired position. 4. After the desired “Transfer Case Position Indicator Light”...
Page 274: Electronically Shifted Transfer Case Operating Information/Precautions (Four Position Switch) - If Equipped
272 STARTING AND OPERATING Electronically Shifted Transfer Case Operating Information/Precautions (Four Position Switch) — If Equipped This is an electronically shifted transfer case and is operated by the transfer case switch, which is located on the instrument panel. Transfer Case Switch (Four Position) This electronically shifted transfer case provides four mode positions.
Page 275 LOW positions are designed for loose, slippery road surfaces only. Driving in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause in- creased tire wear and damage to the driveline compo- nents. NEUTRAL Button STARTING AND OPERATING 273 NOTE: The transfer case NEUTRAL position is selected by depressing the recessed button located on the lower left hand corner of the transfer case switch.
Page 276 274 STARTING AND OPERATING 2. The selected “Transfer Case Position Indicator Light” will flash until the transfer case completes the shift. 3. When the shift is completed, the “Transfer Case Posi- tion Indicator Light” for the selected position will stop flashing and remain ON.
Page 277 NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning, as this can cause damage to driveline components. When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed.
Page 278: Shifting Procedure - Electronically Shifted Transfer Case
276 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position see the information below: Rear Wheel Drive High Range - This range is for normal street and highway driving on dry hard surfaced roads. 4WD LOCK Four-Wheel Drive Lock Range - This range locks the front and rear driveshafts together forcing the front and rear...
Page 279 • If all the requirements to select a new transfer case position have been met, the current “Transfer Case Position Indicator Light” will turn OFF, the selected “Transfer Case Position Indicator Light” will flash until the transfer case completes the shift. When the shift is completed, the “Transfer Case Position Indica- tor Light”...
Page 280 278 STARTING AND OPERATING 2. Shift the transmission into NEUTRAL. 3. While still rolling, rotate the transfer case switch to the desired position. 4. After the desired “Transfer Case Position Indicator Light” is ON (not flashing), shift the transmission back into gear.
Page 281: Axle Locker System - Power Wagon Only
AXLE LOCKER SYSTEM — POWER WAGON ONLY This vehicle is equipped with electronically locking front and rear differentials. These differentials, when engaged, mechanically lock together the axle shafts forcing the wheels to spin at an equal rate. This allows the vehicle to maintain its momentum and prevents it from becoming stuck.
Page 282 280 STARTING AND OPERATING The locking axles are controlled by the axle locker switch located on the center console. Locking Axle Switch The switch has three positions, AXLE UNLOCK, REAR LOCK, and FRONT/REAR LOCK. Under normal driv- ing conditions, the switch should be left in the AXLE UNLOCK position.
Page 283 NOTE: Left to right wheel speed difference may be necessary to allow the axle to fully lock. If the indicator light is flashing after placing the switch in the REAR LOCK or FRONT/REAR LOCK position, drive the ve- hicle in a turn or on loose gravel to expedite the locking action.
Page 284: Stabilizer/Sway Bar System - Power Wagon Only
282 STARTING AND OPERATING STABILIZER/SWAY BAR SYSTEM — POWER WAGON ONLY Your vehicle is equipped with an electronic disconnecting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. Due to the use of taller springs, this vehicle has an increased ride height of approximately 1.9 in (48.3 mm) in the front and 1.5 in (38.1 mm) in the rear.
Page 285 WARNING! Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result in serious injury. The front stabilizer bar enhances vehicle stability and is necessary for main- taining control of the vehicle.
Page 286: Safe Off-Road Driving - Power Wagon Only
284 STARTING AND OPERATING WARNING! If the stabilizer/sway bar will not return to On-Road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury.
Page 287 Ramp Travel Index (RTI) The ramp travel index is the distance, in inches, that you can drive your vehicle with one wheel on a 20-degree ramp without lifting any other wheel off the ground. This distance up the ramp divided by the wheelbase of the vehicle and multiplied by 1,000 is the RTI.
Page 288 286 STARTING AND OPERATING Angles A, B, C, and D...
Page 289 Front and Rear (Shown) Differential Height E STARTING AND OPERATING 287 Water Fording Characteristics Water fording characteristic is the vehicle’s ability to cross a body of still water, where the powertrain and drivetrain are safe from water ingestion. This vehicle has high water fording characteristics with the ability to cross a pool of water, without stopping, 24 inches deep at a maximum speed of 10 mph (16 km/h) and a pool of...
Page 290 288 STARTING AND OPERATING using light brake pressure with light throttle will keep the vehicle from jerking or lurching. This technique is also used when you need to stop and restart a vehicle on a steep incline. The Basics Of Off-Road Driving You will encounter many types of terrain driving off- road.
Page 291: Driving In Snow, Mud And Sand
range. This will allow you to idle over obstacles and down hills, with improved control and less effort. Also, use 4L (Low Range) in rain, ice, snow, mud, sand, to get heavy loads rolling, improve traction, or whenever 4H (High Range) traction will not do the job. Driving In Snow, Mud And Sand There is a drastic reduction in traction when driving in snow, mud or sand.
Page 292: Crossing Obstacles (Rocks And Other High Points)
290 STARTING AND OPERATING normally full of debris from previous vehicles getting stuck. As a good practice before entering any mud hole, get out and determine how deep it is, if there are any hidden obstacles and if the vehicle can be safely recovered if stuck.
Page 293 vehicle to a complete stop and then inch the vehicle forward until it makes contact with the object. Apply the throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. WARNING! Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle.
Page 294 292 STARTING AND OPERATING independently. You need to use caution when crossing large obstacles with steep sides. Do not attempt to cross any large obstacle with steep sides at an angle great enough to put the vehicle at risk of a rollover. If you get caught in a rut, dig a small trench to the right or left at a 45-degree angle ahead of the front tires.
Page 295: Hill Climbing
CAUTION! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill Climbing Hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and should not be attempted.
Page 296 294 STARTING AND OPERATING fresh bite into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in REVERSE and back straight down the grade using engine resistance along with the vehicle brakes.
Page 297: Driving Through Water
sure the surface has good traction with firm and stable soils. If possible transverse the incline at an angle heading slightly up or down. WARNING! Driving across an incline increases the risk of a rollover, which may result in severe injury. •...
Page 298 296 STARTING AND OPERATING your vehicle’s abilities and be able to recover it if something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake. If the engine stalls do not attempt to restart it.
Page 299 crossing is the water depth, current and bottom con- ditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. •...
Page 300: Airing Down For Off-Road Driving
298 STARTING AND OPERATING downstream out of control if the water is deep enough to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, the water’s depth, approach angle, bottom condition and if there are any obstacles, then cross at an angle heading slightly upstream using the low and slow technique.
Page 301: Vehicle Recovery
Vehicle Recovery If you drive off-road, you may encounter a situation where you will need to recover your vehicle. Vehicle recovery should always be given consideration before attempting a questionable obstacle. You should never go off-road driving without the ability to recover your vehicle from a situation.
Page 302 300 STARTING AND OPERATING vehicle from DRIVE to REVERSE, while applying throttle after each shift. During this process, for addi- tional traction, try turning your steering wheel quickly back and forth no more than a in mud, sand, or snow try spinning your tires during this process to clean the debris from the tread and improve the traction.
Page 303 straps together using a 1 ⁄ inch hard wood dowel. This will keep the straps from becoming knotted and is safer than using a clevis pin if the strap breaks. Next have the tow vehicle backup, leaving two to three feet worth of slack in the strap.
Page 304: After Driving Off-Road
302 STARTING AND OPERATING out of the situation in a slow controlled manner. This control works well for avoiding further vehicle dam- age. Once you decide it is time to use the winch look for a good anchor point. It needs to be strong enough to hold more than the vehicle’s weight and provide a direction of pull as straight as possible.
Page 305 • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • Check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and sus- pension. Retighten them, if required, and torque to the values specified in the Service Manual.
Page 306: Limited-Slip Differential - If Equipped
304 STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL – IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit per- forms similarly to a conventional differential.
Page 307: Driving Through Water
ability. To reduce this possibility, the following precau- tions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible.
Page 308 306 STARTING AND OPERATING CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing wa- ter.
Page 309: Driving Off-Road - Ram Truck Only
WARNING! • Driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
Page 310: Winch Usage - If Equipped (Power Wagon Only)
308 STARTING AND OPERATING NOTE: After off-road usage, particularly in sand or mud, inspect the underside of the vehicle for accumu- lated dirt at the propeller shaft, axles, U-joints, brake rotors and calipers. Use a hose to clean off any accumulation of dirt or mud. Check the exhaust system and all exposed components for any sign of damage.
Page 311 2. Attach the hook to a suitable anchor point. CAUTION! Be certain the anchor will withstand the load re- quired to tension the wire rope. 3. Apply at least 500 lbs (227 kg) of tension to the rope while winding the rope. Always use care to ensure the rope does not pile up on one side of the drum and is neatly wound onto the drum.
Page 312: Understanding The Features Of Your Winch
310 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components...
Page 313 1. Motor: The winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote Socket: The remote socket allows the remote control to be attached to the control pack to allow the winch to function.
Page 314: Winch Accessories
312 STARTING AND OPERATING Winch Accessories The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop which can slice skin. It is ex- tremely important to wear protective gloves while oper- ating the winch or handling the wire rope.
Page 315: Operating Your Winch
Clevis/D-Shackles: Operating Your Winch D-Shackle is a safe means of connecting the looped ends of cables, straps and snatch • Always use supplied hook strap to hold the hook blocks. The shackle’s pin is threaded to allow easy re- • Never use as a hoist. moval.
Page 316 314 STARTING AND OPERATING WARNING! (Continued) • Always keep hands and clothing clear of the wire rope, hook and fairlead opening during operation and when spooling. • Never wrap wire rope back onto itself. Always use a choker chain, wire choker rope or tree trunk protector on the anchor.
Page 317 General Information Practice using your winch before you get stuck. Some key points to remember when using your winch are: 1. Always take your time to assess the situation and plan your pull carefully. 2. Always take your time when using a winch. 3.
Page 318 316 STARTING AND OPERATING CAUTION! (Continued) • Always keep remote control lead clear of the drum, wire rope and rigging. • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers.
Page 319 3. Disengage the clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserves battery power. Free Spool STARTING AND OPERATING 317 4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point.
Page 320 318 STARTING AND OPERATING and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work. 6. Secure to the anchor point. Once you have established your anchor point, secure the tree-trunk protector or choker-chain around the object.
Page 321 NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural an- chors include trees, stumps and rocks. Hook the cable as low as possible. If no natural anchors are available when recovering another vehicle, your vehicle becomes the anchor point.
Page 322 320 STARTING AND OPERATING 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door.
Page 323 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. STARTING AND OPERATING 321 13. In certain situations you may decide to throw a heavy blanket or similar object over the wire rope.
Page 324 322 STARTING AND OPERATING the vehicle and never near the wire rope or snatch block. Your situation may have other no people zones. No People Zones 15. Begin winching. With the winching vehicles engine on and light tension already on the wire rope, begin winching slowly and steadily.
Page 325 NOTE: • Avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down. • What to look for under load: The wire rope must always spool onto the drum as indicated by the drum rotation decal on the winch.
Page 326 324 STARTING AND OPERATING 18. Rewind the wire rope. The person handling the wire rope should walk the rope in and not let it slide through the hand, control the winch at all times. WARNING! To prevent serious injury, NEVER put your fingers inside the hook area as you are powering-in.
Page 327: Rigging Techniques
20. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and dry place. Winching operations are now complete. Put the cap on the solenoid plug-in. NOTE: Always store the remote control in a protected, clean, dry area.
Page 328 326 STARTING AND OPERATING How to Change the Pulling Direction Change Pulling Directions All winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope.
Page 329: Power Steering
Double Line Because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power.
Page 330: Power Steering Fluid Check
328 STARTING AND OPERATING NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that there is a problem with the power steering system. Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time.
Page 331: Parking Brake
WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturer’s recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 332: Brake System
330 STARTING AND OPERATING a hill, you should apply the parking brake before placing the shift lever in PARK, otherwise, the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. WARNING! •...
Page 333: 3500 Dual Rear Wheel Models Only
If either the front or rear hydraulic system loses normal braking capability, the remaining system will still func- tion with some loss of overall braking effectiveness. This will be evident by increased pedal travel during applica- tion, greater pedal force required to slow or stop, and activation of the “Brake Warning Light”...
Page 334 332 STARTING AND OPERATING The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. The ABS conducts a low-speed selftest at about 10 mph (16 km/h).
Page 335: Electronic Brake Control System - If Equipped
WARNING! (Continued) • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 336: Traction Control System (Tcs)
334 STARTING AND OPERATING NOTE: ABS improves steering control of the vehicle during hard braking maneuvers. WARNING! • ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that af- forded by the condition of the vehicle brakes and tires or the traction afforded.
Page 337: Brake Assist System (Bas)
Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The BAS detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. The system applies optimum pressure to the brakes in emergency braking conditions.
Page 338: Hill Start Assist (Hsa)
336 STARTING AND OPERATING Hill Start Assist (HSA) The HSA system is designed to assist the driver in launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short duration once the driver takes his foot off of the brake pedal.
Page 339 The system will only work if the intended direction of the vehicle and vehicle gear match. For example, if the intended direction is forward up a hill and the vehicle is in DRIVE, and the activation criteria are met, HSA will activate.
Page 340 338 STARTING AND OPERATING WARNING! • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
Page 341: Electronic Roll Mitigation (Erm)
4. Press ESP button four times within twenty seconds. The “ESP/TCS Indicator Light” should appear and dis- appear four times. 5. Rotate the steering wheel 360° clockwise (180° clock- wise from center). 6. Cycle ignition switch OFF then ON. 7. If the sequence was completed properly, the “ESP/ TCS Indicator Light”...
Page 342: Electronic Stability Program (Esp)
340 STARTING AND OPERATING WARNING! (Continued) • ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ERM-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
Page 343 accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. WARNING! • ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
Page 344 342 STARTING AND OPERATING AUTO, the ESP system will be in this mode. This mode should be used for almost all driving situations. ESP should only be turned to “Partial Off” or “ESP Off” for specific reasons as noted below. ESP OFF Switch ESP Partial Off This mode is entered by momentarily depressing the ESP...
Page 345 overcome, turn ESP back on by momentarily depressing the ESP OFF switch. This may be done while the vehicle is in motion. WARNING! In the “Partial Off” mode, the engine torque reduc- tion and stability features are desensitized. There- fore, the enhanced vehicle stability offered by ESP is unavailable.
Page 346 344 STARTING AND OPERATING the stability feature at speeds above 40 mph (64 km/h). The “ESP/TCS Indicator Light” will always be illumi- nated when ESP is off. To turn ESP on again, momen- tarily depress the ESP OFF switch. This will restore the normal “ESP On”...
Page 347: Tsc (Trailer Sway Control)
• Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously. • The ESP Control System will make buzzing or clicking sounds when it is active. This is normal. The sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation.
Page 348: Tire Safety Information
346 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 1 — U.S. DOT Safety Stan- 4 — Maximum Load dards Code (TIN) 2 — Size Designation 5 — Maximum Pressure 3 — Service Description 6 — Treadwear, Traction and Temperature Grades NOTE: •...
Page 349 Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- tion. Example: T145/80D18 103M. Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light truck tire based on U.S.
Page 350 348 STARTING AND OPERATING Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 351: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. DOT = Department of Transportation —...
Page 352: Tire Loading And Tire Pressure
350 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle...
Page 353 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 354 352 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4.
Page 355 STARTING AND OPERATING 353...
Page 356: Tires - General Information
354 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 357: Tire Inflation Pressures
WARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 358: Tire Pressures For High Speed Operation
356 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 359: Radial Ply Tires
loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail.
Page 360: Tread Wear Indicators
358 STARTING AND OPERATING For additional information, refer to “Freeing A Stuck Vehicle” in Section 6. WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one.
Page 361: Life Of Tire
Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
Page 362: Supplemental Tire Pressure Information - If Equipped
360 STARTING AND OPERATING WARNING! • DO NOT use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
Page 363: Tire Chains
TIRE CHAINS Use “Class U” chains on 2500/3500 model trucks, or other traction aids that meet SAE Type “U” specifica- tions. NOTE: Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: •...
Page 364 362 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of 4X2 model trucks. NOTE: • The use of class “U” chains is permitted on the front and rear of 4X4, 2500 model trucks with LT245/ 70R17E tires.
Page 365: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 366 364 STARTING AND OPERATING Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. NOTE: On Canadian vehicles only, if your vehicle is equipped with All-Season type tires on the front and ON/OFF Road type tires mounted on the rear, do not use...
Page 367: Dual Rear Wheels
Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. STARTING AND OPERATING 365 CAUTION! 3500 Dual Rear Tires have only one approved direc-...
Page 368: Tire Pressure Monitor System (Tpms) - If Equipped
366 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire inflation placard pressure. The placard pressure is defined on the Tire and Loading Information label.
Page 369 The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recom- mended cold placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the TPMS warning light to be turned off.
Page 370 368 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Page 371: Tire Pressure Monitor System (Tpms) Tire Light Load Inflation Switch Description - If Equipped
Tire Pressure Monitor System (TPMS) Tire Light Load Inflation Switch Description – If Equipped WARNING! Never operate your vehicle with the TPMS and tire pressures set to the Light Load Inflation Pressure settings if carrying more than two occupants (150 lbs [68 kg] each) plus 200 pounds (91 kg) of cargo.
Page 372 370 STARTING AND OPERATING Tire Light Load Inflation Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label. It is also equipped to be driven with tire pressures appro- priate to either a Light Load condition or the vehicle Max Load condition.
Page 373 Tire Pressure Information label. The Supplemental Tire Pressure Information label is located on the rear face of the driver door. Use an accurate tire gauge to check the tire pressures when lowering all four tire pressures. After all four tire pressures have been lowered to the Light Load inflation pressures, press the tire light load inflation switch.
Page 374: Tire Pressure Monitor System Components
372 STARTING AND OPERATING the max load inflation pressure (cold) values to switch the TPMS system to the max load inflation pressure (cold) low pressure warning threshold. If after pressing the tire light load inflation switch, and tire pressures are below the max load inflation pressure (cold) low pressure warning thresholds, the TPMS low pressure warning telltale light (located in the instrument cluster) will turn...
Page 375 Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, and an au- dible chime will be activated when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle and inflate each tire to the vehicle’s recommended cold placard...
Page 376: General Information
374 STARTING AND OPERATING 1. This spare tire does not have a tire pressure monitor- ing sensor. Therefore, the TPMS will not monitor the tire pressure in the spare tire. 2. If you install the full size spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the “TPM Telltale Light”...
Page 377: Fuel Requirements
The tire pressure sensors are covered under one of the following licenses: United States ..... KR5S120123 Canada ......2671-S120123 FUEL REQUIREMENTS The 5.7L engine is designed to meet all emissions regulations and provide satisfac-...
Page 378: Gasoline/Oxygenate Blends
376 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- lines. Properly-blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the Winter months to reduce carbon monoxide emissions.
Page 379: Mmt In Gasoline
To fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • drain the fuel tank (see your authorized dealer) • change the engine oil and oil filter • disconnect and reconnect the battery to reset the engine controller memory More extensive repairs will be required for prolonged exposure to E-85 fuel.
Page 380: Fuel System Cautions
378 STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
Page 381: Carbon Monoxide Warnings
Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 382 380 STARTING AND OPERATING CAUTION! (Continued) • A poorly fitting gas cap may cause the MIL to turn • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off the fuel tank is full.
Page 383: Loose Fuel Filler Cap (Gas Cap) Message
Loose Fuel Filler Cap (Gas Cap) Message If the vehicle’s diagnostic system determines that the fuel filler cap in loose, improperly installed or damaged, a GASCAP message will be displayed in the instrument cluster. Tighten the gas cap until a “clicking” sound is heard.
Page 384 382 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels).
Page 385: Trailer Towing
then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
Page 386: Common Towing Definitions
384 STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
Page 387 Tongue Weight (TW) The tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The frontal area is the maximum height and maximum width of the front of a trailer.
Page 388 386 STARTING AND OPERATING WARNING! • An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, brak- ing performance, and could result in an accident. • Weight Distributing Systems may not be compat- ible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Rec- reational Vehicle dealer for additional information.
Page 389 STARTING AND OPERATING 387 EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight- Distributing Hitch (Incorrect)
Page 390: Trailer Hitch Classification
388 STARTING AND OPERATING Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck.
Page 391: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 392: 390 Starting And Operating
390 STARTING AND OPERATING Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. •...
Page 393 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 394 392 STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires −...
Page 395 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! •...
Page 396 394 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4-Pin Connector 1 — Female Pins 4 — Park 2 — Male Pin 5 —...
Page 397: Towing Tips
WARNING! Any work done to the vehicles electrical system, or wiring, should be performed by a qualified automo- tive technician, if done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy...
Page 398: Snowplow
NOTE: Before installation of a snowplow, it is highly recommended that the owner/installer obtain and follow the recommendations contained within the current Dodge Body Builder’s Guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems that must be con- nected to properly assure operator safety, and to prevent overloading vehicle systems.
Page 399: Recreational Towing (Behind Motorhome, Etc.)
WARNING! Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an acci- dent. Do not expect that the airbag will perform as described earlier in this manual RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
Page 400 398 STARTING AND OPERATING Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
Page 401 CAUTION! Damage to the transmission may occur if the trans- mission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into PARK. Returning to Normal Operation —...
Page 402 400 STARTING AND OPERATING CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts.
Page 403 11. Repeat steps 9 and 10 with the transmission in DRIVE. 12. Shut the engine OFF and place ignition key in the unlocked OFF position. 13. Shift the transmission into PARK. 14. Apply the parking brake. 15. Attach the vehicle to the tow vehicle with the tow bar. 16.
Page 404 402 STARTING AND OPERATING Returning to Normal Operation — Electronic Shift Transfer Case Use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3. Turn the ignition key to the ON position, but do not start the engine.
Page 405: Equipment Identification Plate
• The ignition key must be ON for a transfer case shift to take place and for the position indicator lights to be operable. If the key is not ON, the shift will not take place and no position indicator lights will be on or flashing.
Page 407: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....406 Jacking Instructions ....407 Jack Location .
Page 408: Hazard Warning Flasher
406 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is mounted on the top of the steering column. Hazard Warning Flasher Switch Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.
Page 409: Jacking Instructions
JACKING INSTRUCTIONS WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 410: Removing The Spare Tire
408 WHAT TO DO IN EMERGENCIES Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Page 411: Tire Changing Procedure
NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
Page 412: Instructions
410 WHAT TO DO IN EMERGENCIES 3. Place the shift lever into PARK. On four-wheel drive vehicles, shift the transfer case to the 4L position. 4. Turn the ignition OFF. 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite the jacking position.
Page 413 WARNING! (Continued) • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
Page 414 412 WHAT TO DO IN EMERGENCIES • Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required. • For 2500/3500 4x4 series trucks, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 415 Rear Jacking Location (All) • Connect the jack tube extension and wheel wrench. Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. WHAT TO DO IN EMERGENCIES 413 NOTE: If the 2500/3500 bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be neces- sary to use the jack drive tube in order to lower the jack.
Page 416: Hub Caps/Wheel Covers
414 WHAT TO DO IN EMERGENCIES face. Lightly tighten the nuts. To avoid risk of forcing the vehicle off the jack, do not fully tighten the nuts until the vehicle has been lowered. 6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern.
Page 417 Insert the blade end into the pry-off notch and carefully pop off the hub cap with a back-and-forth motion. On 3500 models with dual rear wheels (DRW), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pry off notch of the rear hub caps.
Page 418 416 WHAT TO DO IN EMERGENCIES 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer.
Page 419 These dual rear wheels should be tightened as follows: Tightening Pattern 1. Tighten the wheel nuts in the numbered sequence to a snug fit. WHAT TO DO IN EMERGENCIES 417 2. Retighten the wheel nuts in the same sequence to the torques listed in the table.
Page 420: Hoisting
418 WHAT TO DO IN EMERGENCIES circle, tightening the nut opposite to the nut just previ- ously tightened until final torque is achieved. Recom- mended torques are shown in the following chart. Disc Type Nut Stud Size Torque Wheels Cone 9/16-18 Flanged 9/16-18...
Page 421: Jump-Starting Procedures
CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. JUMP-STARTING PROCEDURES Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmis- sion cannot be started this way.
Page 422 420 WHAT TO DO IN EMERGENCIES 2. Park the booster vehicle within cable reach but with- out letting the vehicles touch. Set the parking brake on both vehicles, place the automatic transmission in PARK and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electri- cal loads.
Page 423: Freeing A Stuck Vehicle
6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: •...
Page 424: Emergency Tow Hooks - If Equipped
422 WHAT TO DO IN EMERGENCIES EMERGENCY TOW HOOKS — IF EQUIPPED Your vehicle may be equipped with emergency tow hooks. NOTE: For off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle.
Page 425: 4-Wheel Drive Vehicles
4-Wheel Drive Vehicles CAUTION! To avoid damage to the transfer case while towing, always use one of the following methods. • The transfer case must be in the neutral position, and the transmission must be in PARK to tow a 4-Wheel Drive vehicle with one end of the vehicle raised.
Page 427: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment— 5.7L ... . . 427 Onboard Diagnostic System (OBD II) Loose Fuel Filler Cap Message Emissions Inspection And Maintenance Programs ......429 Replacement Parts .
Page 428 426 MAINTAINING YOUR VEHICLE Cooling System ....441 Brake System ..... . 447 Rear Axle And 4X4 Front Driving Axle Fluid Level .
Page 429: Engine Compartment- 5.7L
ENGINE COMPARTMENT— 5.7L 1 — Air Cleaner Filter 2 — Automatic Transmission Dipstick 3 — Engine Oil Fill 4 — Brake Fluid Reservoir 5 — Battery 6 — Integrated Power Module MAINTAINING YOUR VEHICLE 427 7 — Power Steering Fluid Reservoir 8 —...
Page 430: Onboard Diagnostic System (Obd Ii)
428 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 431: Emissions Inspection And Maintenance Programs
appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
Page 432: Replacement Parts
430 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
Page 433: Maintenance Procedures
your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
Page 434 432 MAINTAINING YOUR VEHICLE dipstick. Adding one quart of oil when the reading is at the bottom of the SAFE zone will result in a reading at the top of the safe zone on these engines. CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure.
Page 435: Engine Oil Filter
NOTE: For 2500/3500 trucks with a 5.7L engine oper- ating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, SAE 5W-30 engine oil is recom- mended for all operating temperatures. Lubricants, which do not have both the engine oil certi- fication mark and the correct SAE viscosity grade num- ber, should not be used.
Page 436: Engine Air Cleaner Filter
434 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire.
Page 437: Air Conditioner Maintenance
WARNING! (Continued) • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 Volts. Do not allow cable clamps to touch each other. •...
Page 438: Front Prop Shaft Lubrication - 2500/3500 (4X4) Models
436 MAINTAINING YOUR VEHICLE include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system.
Page 439: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- cated periodically with a lithium based grease such as MOPAR Spray White Lube to assure quiet, easy opera- tion and to protect against rust and wear.
Page 440: Adding Washer Fluid
438 MAINTAINING YOUR VEHICLE Adding Washer Fluid The fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not ra- diator antifreeze). When refilling the washer fluid reser- voir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance.
Page 441 Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 442 440 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 443: Cooling System
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
Page 444 442 MAINTAINING YOUR VEHICLE accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection at the bottle and radiator.
Page 445 CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corro- sion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible.
Page 446 444 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below -34°F (-37°C) are anticipated.
Page 447 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 448 446 MAINTAINING YOUR VEHICLE When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 449: Brake System
• Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Brake System Master Cylinder — Brake Fluid Level Check The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system...
Page 450: Rear Axle And 4X4 Front Driving Axle Fluid Level
448 MAINTAINING YOUR VEHICLE WARNING! (Continued) • Use only brake fluid that has been in a tightly- closed container to avoid contamination from for- eign matter or moisture. CAUTION! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Rear Axle And 4x4 Front Driving Axle Fluid Level For normal service, periodic fluid level checks are not required.
Page 451: Transfer Case
NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. 2500/3500 Model Axles DO NOT REQUIRE any limited slip oil additive (friction modifiers).
Page 452 450 MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes.
Page 453 3. Fully apply the parking brake and press the brake pedal. 4. Place the shift lever momentarily into each gear posi- tion ending with the lever in PARK. 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6.
Page 454: Appearance Care And Protection From Corrosion
452 MAINTAINING YOUR VEHICLE dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Automatic Transmission Fluid and Filter Change Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.
Page 455 What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. •...
Page 456 454 MAINTAINING YOUR VEHICLE Special Care • If you drive on salted or dusty roads, or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open.
Page 457 oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Stain Repel Fabric Cleaning Procedure — If Equipped You can identify if your vehicle has Stain Repel Seat Fabric that makes spills easy to clean, reduces odor from spills and reduces static by the presence of a tag on the side of the seat.
Page 458 456 MAINTAINING YOUR VEHICLE soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. WARNING! Do not use volatile solvents for cleaning purposes.
Page 459 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 460: Fuses
458 MAINTAINING YOUR VEHICLE FUSES Integrated Power Module The integrated power module is located in the engine compartment near the battery. This center contains car- tridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 461 Cavity Cartridge Mini Fuse Fuse 20 Amp Power Outlet Console Yellow 20 Amp Cabin Compartment Yellow Node (CCN) Door Locks — — 15 Amp Aisin Transmission Blue Controls (Diesel Only) 20 Amp Power Sunroof Yellow 10 Amp Vistronic Fan/ Wastegate Solenoid —...
Page 462 460 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 30 Amp Pink 25 Amp Natural 15 Amp Blue 20 Amp Yellow 15 Amp Blue — 40 Amp Green 30 Amp Pink Description Cavity Cartridge Electric Brake Power-Battery RWAL/ABS Module Feed Park Lights Left Trailer Park Lights Park Lights Right...
Page 463 Cavity Cartridge Mini Fuse Fuse 40 Amp Power Seats Green 10 Amp Power Run/Start- PCM/Steering Angle Sensor 10 Amp 4X4 Switch/Pass Dr Switch/EC Mirror 15 Amp Power Run/Start- Blue ABS/RWAL/Smart Bar/YAW Sensor/ Universal Exhaust Gas Oxygen (Uego) Sensor Controller 10 Amp PCM (Gas)/TCM (Diesel 58RFE) Description...
Page 464 462 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 10 Amp 20 Amp Yellow — 30 Amp Pink Description • When installing the Integrated Power Module Seatbelt Tension cover, it is important to ensure the cover is prop- Reducer/Power IGN erly positioned and fully latched.
Page 465: Vehicle Storage
VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
Page 466: Replacement Light Bulbs
464 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Overhead Console Lights ....TS 212-2 Dome Light......7679 NOTE: For lighted switches, see your authorized dealer for replacement instructions.
Page 467: Bulb Replacement
BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two bolts from the front of the headlight housing.
Page 468 466 MAINTAINING YOUR VEHICLE 3. Remove the plug from the inner fender well and remove the nut through the access hole. Inner Fender Plug Rear Headlight Housing Nut Access 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
Page 469 MAINTAINING YOUR VEHICLE 467 Bulb Removal Headlight Removal 5. Unlock and pull the connector straight from the base of the headlight halogen bulb. 6. Twist the connector on the side marker/turn signal/ park light bulb ⁄ turn and remove the connector and bulb from housing.
Page 470: Fog Lights
468 MAINTAINING YOUR VEHICLE 7. Remove the housing from vehicle with the headlight halogen bulb in housing. 8. Twist the headlight halogen bulb the headlight bulb from the housing. 9. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb. 10.
Page 471: Tail, Stop, Turn And Backup Lights
2. Pull the bulb straight from the connector. 3. Reverse the procedure for installation of the bulbs and housing. MAINTAINING YOUR VEHICLE 469 Tail, Stop, Turn and Backup Lights 1. Remove the two screws that pass through the bed sheetmetal. Removing The Two Screws...
Page 472 470 MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. Pulling Housing From Body 3. Rotate the bulb socket counterclockwise to remove from the housing.
Page 473 MAINTAINING YOUR VEHICLE 471 4. Pull the bulb straight out of socket. 5. Reverse the procedure to install the bulb and housing. Place the two raised blocks past the body. Pulling Bulb From Socket Sliding Raised Blocks Past Body...
Page 474: Center High-Mounted Stoplight (Chmsl) With Cargo Light
472 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn the desired bulb socket socket and bulb from housing.
Page 475: Cab Top Clearance Lights - If Equipped
4. Pull the desired bulb straight from the socket. • Outside Bulbs: Cargo Lights • Inside Bulb: Center High-Mounted Stop Light 5. Reverse the procedure for installation of the bulbs and housing. MAINTAINING YOUR VEHICLE 473 Cab Top Clearance Lights — If Equipped 1.
Page 476 474 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the light 3. Pull the bulb straight from it’s socket and replace. assembly.
Page 477: Tailgate Id Lights (Dual Rear Wheels) - If Equipped
MAINTAINING YOUR VEHICLE 475 Tailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the rear.
Page 478: Rear Light Bar Id Marker (Dual Rear Wheel) - If Equipped
476 MAINTAINING YOUR VEHICLE 2. Turn the socket ⁄ turn counterclockwise to access the bulb. 3. Pull the bulb straight out from socket. 4. Reverse the procedure for installation of the bulbs and housing. Rear Light Bar ID Marker (Dual Rear Wheel) — If Equipped 1.
Page 479: Side Marker Lights (Dual Rear Wheels)
3. Pull the bulb straight out from the socket. 4. Reverse the procedure for installation of the bulbs and housing. Side Marker Lights (Dual Rear Wheels) MAINTAINING YOUR VEHICLE 477 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender. 3.
Page 480: Fluids And Capacities
478 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 2500/3500 Shortbed Models 2500/3500 Longbed Models Engine Oil with Filter 5.7L Engine (SAE 5W-20, API Certified). For trucks oper- ating under a gross combined weight rating less than 14,000 lbs (6 350 kg). 5.7L Engine (SAE 5W-30, API Certified).
Page 481: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil — 5.7L Engine (For trucks operating under a gross com- bined weight rating less than 14,000 lbs/(6,350 kg.) Engine Oil — 5.7L Engine (For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs/(6,350 kg.) Engine Oil Filter...
Page 482: Chassis
480 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case NVG 246 Automatic Transfer Case Only 2500/3500 Model Front and Rear Axle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR ATF+4 Automatic Transmission Fluid MOPAR ATF+4 Automatic Transmission Fluid MOPAR PN 05179014AA, NVG 246 Automatic Transmission Fluid or equivalent Synthetic, GL-5 SAE, 75W-90 or equivalent.
Page 483: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance Maintenance Schedule ....483 ..482 Required Maintenance Intervals ..484...
Page 484 482 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability.
Page 485 MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. The “Change Oil” message will flash in the instrument cluster odometer and a single chime will sound, indicat- ing that an oil change is necessary.
Page 486 484 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 487 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule...
Page 488 486 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front & rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 489: Service Schedule
30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L engine). ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only).
Page 490 488 MAINTENANCE SCHEDULES 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). Odometer Reading Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service...
Page 491 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front & rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 492 490 MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). Odometer Reading Repair Order # Dealer Code Signature Authorized Chrysler Dealer 72,000 Miles (120,000 km) or 72 Months Maintenance Service...
Page 493 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 84,000 Miles (140,000 km) or 84 Months Maintenance...
Page 494 492 MAINTENANCE SCHEDULES 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L engine). ❏ Inspect and replace PCV valve if necessary. † ❏...
Page 495 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏...
Page 496 494 MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
Page 497 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (5.7L engine). ❏ Inspect the brake linings, replace if necessary. ❏...
Page 498 496 MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Lube front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front & rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 499 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏...
Page 500 498 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 501: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle......501 Prepare For The Appointment Prepare A List .
Page 502 500 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Quality Grades ......506 Treadwear ......507 Traction Grades .
Page 503: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 504: Chrysler Llc Customer Center
502 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Page 505: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 506: Warranty Information (U.s. Vehicles Only)
504 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
Page 507: In Canada
To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administra- tor, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Page 508 506 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 509 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
Page 510 508 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 511 INDEX...
Page 512 510 INDEX Adding Fuel ......379 Adjustable Pedals ..... . . 141 Air Cleaner, Engine (Engine Air Cleaner Filter) .
Page 513 Bar, Stabilizer/Sway System ....282 Battery ....... 434 Emergency Starting .
Page 514 512 INDEX Chart, Tire Sizing ......347 Check Engine Light (Malfunction Indicator Light) ... . . 194,429 Checking Your Vehicle For Safety .
Page 515 Dealer Service ......430 Defroster, Rear Window ....172 Defroster, Windshield .
Page 516 514 INDEX Towing ......422 Emission Control System Maintenance ..429,482 Engine .
Page 517 Fluids, Lubricants and Genuine Parts ..479 Fog Lights ..... . . 135,193,468 Fold Flat Load Floor .
Page 518 516 INDEX Hazard Driving Through Flowing, Rising, or Shallow Standing Water ......305 Hazard Warning Flasher ....406 Head Restraints .
Page 519 Intermittent Wipers (Delay Wipers) ... 138 Introduction ......4 Jack Operation .
Page 520 518 INDEX Electronic Stability Program (ESP) Indicator ......197,340 Engine Temperature Warning ....200 Exterior .
Page 521 Power Door ......28 Steering Wheel ......14 Lower Anchors and Tether for CHildren (LATCH) .
Page 522 520 INDEX Oil Change Indicator ..... 193 Oil Change Indicator, Reset ....193 Oil, Engine .
Page 523 Power Door Locks ......28 Mirrors ......84 Outlet (Auxiliary Electrical Outlet) .
Page 524 522 INDEX Remote Sound System (Radio) Controls ..231 Remote Starting System ....25 Replacement Keys .
Page 525 Rear Folding ..... . . 126,127 Reclining ......121,122 Reclining Rear .
Page 526 524 INDEX Steering Power ......327,328 Wheel Lock ......14 Wheel, Tilt .
Page 527 Life of Tires ......359 Load Capacity ..... 350,351 Pressure Monitor System (TPMS) .
Page 528 526 INDEX Transaxle Automatic ......12 Transfer Case ......449 Electronically Shifted .
Page 529 Water Driving Through ..... . 305 Wheel and Wheel Trim ....454 Wheel and Wheel Trim Care .
Page 530 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VAN CONVERSIONS/CAMPERS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalLocking Doors With A KeySTEERING WHEEL LOCK - IF EQUIPPED To Manually Lock the Steering WheelTo Release the Steering Wheel LockAutomatic Transmission Ignition Interlock SystemSENTRY KEY Replacement KeysCustomer Key ProgrammingGeneral InformationVEHICLE SECURITY ALARM - IF EQUIPPED Rearming of the SystemTo Set the AlarmTo Disarm the SystemILLUMINATED ENTRY SYSTEM - IF EQUIPPED REMOTE KEYLESS ENTRY (RKE) - IF EQUIPPED To Unlock the DoorsTo Lock the DoorsUsing the Panic AlarmProgramming Additional RKE TransmittersGeneral InformationRKE Transmitter Battery ServiceREMOTE STARTING SYSTEM - IF EQUIPPED How to Use Remote StartDOOR LOCKS Manual Door LocksPower Door Locks - If EquippedChild Protection Door LockWINDOWS Power Windows-If Equipped Wind BuffetingOCCUPANT RESTRAINTS Lap/Shoulder BeltsAdjustable Upper Shoulder Belt AnchorageAutomatic Locking Retractors (ALR) Mode - If EquippedCenter Lap Belts...
Page 531 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 532 Chrysler LLC 81-326-0927 Third Edition Printed in U.S.A.

This manual is also suitable for:

2009 ram 3500 2009 ram truck

Dodge 2009 Ram 1500 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

144 Understanding the Features of Your Vehicle

Understanding the Features of Your Vehicle 151

172 Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge 2009 Ram 1500

Summary of Contents for Dodge 2009 Ram 1500