Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Van Conversions/Campers
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Identification Number
VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove the VIN.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry — If Equipped ..20 To Unlock The Doors ....20 To Lock The Doors .
Page 11 Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags ...47 Event Data Recorder (EDR) ....58 Child Restraint ......60 Occupant Restraints (2500/3500/Mega Cab Only) .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Manual Transmission—If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle.
Page 15: Steering Wheel Lock - If Equipped
STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle. The system will shut the engine off in two (2) seconds if someone uses an invalid key to start the engine. NOTE: A key, which has not been programmed, is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle.
Page 17: Customer Key Programming
NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. •...
Page 19: To Disarm The System
NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by your dealer. To Disarm the System: Use the Keyless Entry transmitter to unlock the door. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds.
Page 20: Remote Keyless Entry - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED Three Button Transmitter This system allows you to lock or unlock the doors from distances up to about 23 feet (7 meters) using a hand held radio transmitter.
Page 21: To Lock The Doors
4. Release both buttons at the same time. 5. This will allow you to unlock all doors on the first press of the UNLOCK button. To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. To reactivate this feature, repeat the above steps. Using the Panic Alarm To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
Page 23: Transmitter Battery Service
2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service Transmitter Battery Replacement The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board.
Page 24: Remote Starting System - (Gas Engine Only)
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — (GAS ENGINE ONLY) Your vehicle may be equipped with a remote starting system, which will allow the vehicle to be started from distances up to approximately 300 feet away from the vehicle using the remote keyless entry key fob which is part of your ignition key.
Page 25 To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the UNLOCK button on the key fob. After the vehicle is unlocked, you have 60 seconds to enter the vehicle, insert the key in the Ignition and move it to the RUN position, otherwise the engine will cancel remote start and auto- matically turn off.
Page 26: Door Locks
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Front and Rear doors may be locked, by moving the lock plunger up or down. All doors may be opened with the inside door handle without lifting the lock plunger. Doors locked before closing will remain locked when closed.
Page 27: Power Door Locks - If Equipped
Power Door Locks — If Equipped A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch Location If you press the power door lock switch while the key is in the ignition, and any front door is open, the power THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 locks will not operate.
Page 28 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 15 seconds cycle the key from the LOCK position to the ON/RUN position a minimum of four times;...
Page 29: Child Protection Door Lock
4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times ending in the LOCK position (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To use the system, open each rear door, insert the tip of the ignition key or alike object into the lock control lever, slide the lever UP to engage the locks and DOWN to disengage the child-protection locks.
Page 31: Windows
WINDOWS Power Windows—If Equipped Power Window Switches The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 and on the rear doors of Quad Cab and Mega Cab models.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Page 33: Wind Buffeting
Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized.
Page 34: Lap/Shoulder Belts
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.
Page 35 WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
Page 37 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! • A belt buckled into the wrong buckle will not protect you properly.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 39 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The black buckle latch plate can be removed when the key is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Inserting Latch Plate In Use Position...
Page 42: Adjustable Upper Shoulder Belt Anchorage
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 43: Automatic Locking Retractors (Alr) Mode - If Equipped
Automatic Locking Retractors (ALR) Mode – If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is avail- able on all passenger seating positions with a combina- tion lap/shoulder belt.
Page 44: Seat Belt Pretensioners
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. •...
Page 45 if the ignition is cycled, driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON...
Page 46: Seat Belts And Pregnant Women
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible.
Page 47: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbags
Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger front airbag is mounted in THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 the instrument panel, above the glove compartment.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 49 Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 51 • Driver and Front Passenger Seat Belt Pretensioners • Driver Seat Track Position Sensor (If Equipped) • Passenger Side Frontal Airbag ON/OFF Switch (Stan- dard Cab Vehicles Only) • Passenger Airbag Disable (PAD) Indicator Light (Stan- dard Cab Vehicles Only) How the Airbag System Works •...
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 53 units. A large quantity of nontoxic gas is generated to inflate the front airbags. Different airbag inflation rates may be possible based on collision severity and occu- pant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which...
Page 55 WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. To Shut Off the Passenger Airbag (Standard Cab Ve- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove...
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
Page 57 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 58: Event Data Recorder (Edr)
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection.
Page 59 may be released for incorporation in aggregate crash databases, such as those maintained by the US govern- ment and various states. Data of a potentially sensitive nature, such as would identify a particular driver, ve- hicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1.
Page 60: Child Restraint
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems.
Page 61 Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: • Safety experts recommend that rearward-facing in the vehicle until they are at least...
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning-booster seat.
Page 63 Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 NOTE: For children riding in the front seat of a Stan- dard Cab model refer to the “Passenger Airbag On/Off Switch” located in this section. Standard Cab Passenger Seat Quad Cab Rear Outboard Seats...
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time.
Page 67 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating posi- tions only.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 69 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. Regular Cab Tether Strap Mounting THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats)
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Multiple Child Restraint Quad Cab...
Page 72: Occupant Restraints (2500/3500/Mega Cab Only)
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
Page 73: Lap/Shoulder Belts
WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle WARNING! • A belt buckled into the wrong buckle will not protect you properly.
Page 77 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 78 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position.
Page 79 Standard Cab Front Center Three Point Belt 1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
Page 80 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 81: Adjustable Upper Shoulder Belt Anchorage
In Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 82: Automatic Locking Restraint (Alr) Mode - If Equipped
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 83: Center Lap Belts
Center Lap Belts The center seating position for the Quad Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a click. To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing.
Page 84: Enhanced Driver Seat Belt Reminder System (Beltalert)
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver to buckle their seat belt.
Page 85: Seat Belts And Pregnant Women
The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies.
Page 86: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbag
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 87 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 88 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. • Children 12 years and under should ride buckled up in a rear seat, if available. •...
Page 89 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 90 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows. • Airbag Control Module (shared with the front airbag system) •...
Page 91 WARNING! Ignoring the AIR BAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 92 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which...
Page 93 WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death. To Shut Off the Passenger Airbag (Standard Cab Ve- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn clockwise, and remove...
Page 94 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
Page 95 Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions. The airbag control module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions.
Page 96 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you.
Page 97: Event Data Recorder (Edr)
for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper airbag fuses. See your dealer if the fuse is good. Event Data Recorder (EDR) In the event of an airbag deployment, your vehicle is designed to record up to 2-seconds of specific vehicle data parameters (see the following list) in the event data recorder prior to the moment of airbag deployment.
Page 98 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE nature, such as would identify a particular driver, ve- hicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1.
Page 99: Child Restraint
Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Page 100 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: •...
Page 101 • The belt-positioning booster seat is for children weigh- ing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning-booster seat.
Page 102 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 103 • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position.
Page 104 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors. NOTE: For children riding in the front seat of a Stan- dard Cab model refer to the “Passenger Airbag On/Off Switch”...
Page 105 Mega Cab Rear Seats Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 some time.
Page 106 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
Page 107 rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages.
Page 108 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 109 Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up”...
Page 110 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Quad Cab...
Page 111 Tether Anchorage Points at All Three Seating Positions (Mega Cab) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat.
Page 112: Engine Break-In Recommendations
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
Page 113 CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • Limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113...
Page 115: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......121 Inside Mirror ......121 Automatic Dimming Mirror—...
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats (1500 Standard And Quad Cab Models) ..150 Reclining Seats (2500/3500/Mega Cab Models) ... 151 Adjustable Head Restraints ....151 Manual Rotary Lumbar Support Adjustment —...
Page 117 Tilt Steering Column ....173 Driver Adjustable Pedals — If Equipped ..174 Adjustment ......174 Electronic Speed Control —...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recalibrating The Compass ....184 Outside Temperature ....186 Garage Door Opener —...
Page 119 Front Instrument Panel Cupholders — Manual Transmission ....201 Rear Cupholder — Quad Cab — If Equipped ......202 Rear Cupholder —...
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exhaust Gas ......218 Safety Checks You Should Make Inside The Vehicle .
Page 121: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 122: Automatic Dimming Mirror- If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 123: Exterior Mirrors Folding Feature
WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror.
Page 124: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirror Switches Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: Fold the 7 x 10 inch trailer towing mirrors rearward prior to entering an automated car wash. Trailer Towing Position Blindspot Mirror...
Page 126: Hands-Free Communication (Uconnect™) - If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., Call” “Mike” ”Work or Dial” “248-555-1212 ).
Page 127: Operations
UConnect™ Switches The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Headset Profile), you may not be able to use any UCon- nect™...
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for the voice on beep, which follows the Ready prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying Setup and then Phone Pairing, the following compound command can be said: Setup Phone Pairing.
Page 129 NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 The following are general phone to UConnect™ System pairing instructions: •...
Page 130 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system. However, at any given time, only one cellular phone can be in use, connected to your UConnect™...
Page 131 you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect™ phone- book. Refer to Add Names to Your UConnect™ Phonebook, to learn how to store a name in the phonebook. • The UConnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios.
Page 132 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook Editing phonebook entries is recommended NOTE: when vehicle is not in motion. •...
Page 133 • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say List Names to hear a list of the entries in the phonebook from which you choose.
Page 134: Phone Call Features
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the Voice Recognition’ button during the playing of the desired name, and then say Call. NOTE: the user can also exercise Edit or Delete operations at this point. •...
Page 135 Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say Dial or Call followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress.
Page 136: Uconnect™ System Features
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination To end a call in progress, momentarily press the Phone’ button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. Redial •...
Page 137 • After the Ready prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
Page 138 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UCon- nect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, •...
Page 139 When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word Send. For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the ’Voice Recognition’...
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures).
Page 141: Advanced Phone Connectivity
Information Service When using AT&T Wireless Service, dialing to phone number #121, you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. Advanced Phone Connectivity Transfer Call to and from Cellular Phone The UConnect™ system allows on going calls to be transferred from your cellular phone to the UConnect™...
Page 142: Things You Should Know About Your Uconnect™ System
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. •...
Page 143 • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: •...
Page 144 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. •...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145...
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147...
Page 148: Seats
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing...
Page 149: 40-20-40 Front Seat
40-20-40 Front Seat Manual Seat Adjuster As the name implies, the seat is divided into 3 segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
Page 150: Reclining Seats (1500 Standard And Quad Cab Models)
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats (1500 Standard and Quad Cab Models) The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. Seat Recliner Handle WARNING! You can be seriously, even fatally, injured riding in a...
Page 151: Reclining Seats
Reclining Seats (2500/3500/Mega Cab Models) The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. Manual Recline Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined.
Page 152: Manual Rotary Lumbar Support Adjustment - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, push in the button and then push down on the head restraint. Head Restraints Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar (lower back) support.
Page 153: Power Seats (1500 Standard And Quad Cab Models) - If Equipped
Power Seats (1500 Standard and Quad Cab Models) — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Power Seat Switch...
Page 154: Power Seats (2500/3500/Mega Cab Models) - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power seat controls are on the outboard side of the front seat cushions. One switch controls the seat move- ment. The six-way switch can be moved forward or back- wards to get the most comfortable position. The same switch can be moved up and down to control seat height or to change the seat angle by tilting it up or down.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Power Seat Switch Up, Down, Forward, and Rearward...
Page 156: Rear Seat Features - Mega Cab Models
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat move- ment. The four-way switch in the center can be moved forward or backwards to get the most comfortable posi- tion.
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Folding Rear Seat (Table Mode) — Mega Cab Models Both the left and right rear seat backs can be folded down and used as a table. To fold either rear seat back down (Table Mode), lift the handle and fold the seat back forward.
Page 158 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Table Mode Folding Rear Seat (Kneel Mode) — Mega Cab Models Both the left and right rear seats can be folded flat (Kneel Mode) and used for carrying cargo. Each of the rear seat backs provide 2 D-rings and each of the rear storage bin lids provide 2 slotted cutouts.
Page 159 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 160 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The rear seat will drop and move forward in Kneel Mode. To fold either rear seat flat (Kneel Mode), lift the handle and fold the seat forward. Simply lift the seat back to return the seat to the upright position.
Page 161: Heated Seats - If Equipped
WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Heated Seats —...
Page 162 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE level, or OFF. The High heat level operates for 30 minutes (approximate), the Low heat level operates for 30 min- utes (approximate). The seat heat will also turn OFF when the ignition is turned OFF. Both of the indicators ON identifies High heat level.
Page 163: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD Hood Release Lever To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 released you must reach into the opening beneath the center of the grille and push up the latch to release the...
Page 164: Lights
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. Headlight Switch Location...
Page 165: Interior Lights
Interior Lights Dimmer Control Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the key fob.
Page 166: Battery Saver
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver To protect the life of your vehicle’s battery, Load Shed- ding is provided for both the interior and exterior lights. If the ignition is off and any door is left ajar for 10 minutes or the dimmer control is rotated upwards for 10 minutes, the interior lights will automatically turn off.
Page 167: Daytime Running Lights (Canada Only And Fleet Vehicles)
Light Switch Rotation Your vehicle is equipped with plastic headlight lenses that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.
Page 168: Lights-On Reminder
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-on Reminder If the headlights, parking lights, or cargo lights are left on, after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The foglights are turned ON by placing the head- light rotary control in the parking light or head- light position and pushing in the headlight rotary...
Page 169: Multifunction Control Lever
Multifunction Control Lever The multifunction control lever is located on the left side of the steering column. Turn Signals Move the lever up or down to signal a right-hand or left-hand turn. The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights.
Page 170 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or...
Page 171: Windshield Wipers And Washers
WINDSHIELD WIPERS AND WASHERS Windshield Wipers Windshield Wiper / Washer Switch The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle,...
Page 172: Windshield Washers
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during wind- shield washer use.
Page 173: Tilt Steering Column
TILT STEERING COLUMN To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forward to lock the column firmly in place. Tilt Steering Control Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 WARNING! Tilting the steering column while the vehicle is...
Page 174: Driver Adjustable Pedals - If Equipped
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Adjustable Pedals Switch The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
Page 175: Electronic Speed Control - If Equipped
CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL —...
Page 176: To Activate
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on. To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button.
Page 177: To Vary The Speed Setting
To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine).
Page 178: To Accelerate For Passing
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
Page 179: Overhead Console- If Equipped
OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: Overhead Console Features • Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC) — If Equipped UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 • Universal Garage Door Opener — If Equipped Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
Page 180: Overhead Console With Compass/Temperature Mini-Trip Computer - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC) This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored.
Page 181: Reset Button
RESET Button Use this button to reset the following displays: Average Fuel Economy (AVG ECO) Trip Odometer (ODO) Elapsed time (ET) UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays (AVG ECO, ODO, ET), the Global Reset will reset all 3 displays.
Page 182: Average Fuel Economy (Avg Eco)
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. Average fuel economy is a running average of the amount of fuel used and the distance the vehicle has traveled.
Page 183: Trip Odometer (Odo)
Ram fuel tank volumes are as follows: • 26 gallons - 1500 short box models • 34 gallons - 1500 Quad Cab (if equipped)/2500/3500 short box models • 35 gallons - 1500/2500/3500 long box models Trip Odometer (ODO) This display shows the distance traveled since the last reset.
Page 184: Automatic Compass Calibration
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
Page 186: Outside Temperature
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The default for the compass variance is zone 8. To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press and hold the RESET button approximately five seconds. The last vari- ance zone number will be displayed.
Page 187 HomeLink Programming Buttons For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
Page 188: Programming Homelink
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause seri- ous injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 189 Outer HomeLink buttons 2. Position the end of your hand-held transmitter 1-3 inches (3-8 cm) away from the HomeLink buttons while keeping the indicator light in view. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter buttons.
Page 190: Canadian Programming/Gate Programming
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink but- tons, begin with Programming step two. Do not repeat step one. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener).
Page 191: Using Homelink
Similar to this Canadian law, some U.S. gate operators are designed to time-out in the same manner. If you live in Canada or you are having difficulties programming a gate operator by using the Program- ming procedures (regardless of where you live), replace Programming HomeLink step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the...
Page 192: Erasing Homelink Buttons
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Erasing HomeLink Buttons To erase programming from the three buttons (individual buttons cannot be erased but can be reprogrammed - note below), follow the step noted: • Press and hold the two outer HomeLink buttons until the indicator light begins to flash-after 20 seconds.
Page 193: Power Sunroof - If Equipped
Changes or modifications not expressly ap- NOTE: proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console.
Page 194: Open Sunroof - Express Mode
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Open Sunroof - Express Mode Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position.
Page 195: Pinch Protect Override
Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed.
Page 196: Sunroof Maintenance
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in cab accessories designed for use with the standard “cigar...
Page 197 All accessories connected to this/these outlet(s) should be removed or turned OFF when the vehicle is not in use to protect the battery against discharge. NOTE: If desired, all of the power outlets can be converted by your authorized dealer to provide power with the ignition switch in the ON position only.
Page 198: Cigar Lighter And Ash Receiver
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER The removable ash receiver is located in the instrument panel cup holder tray. The cigar lighter is located on the instrument panel, above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON.
Page 199: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission Your new Ram truck is equipped with two adjustable cupholders. The cupholder is opened by pulling on the cup holder door handle, on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes.
Page 200 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. Cup Holders Automatic Transmission Cup Holder Door Handle...
Page 201: Front Instrument Panel Cupholders (Bucket Seats) - Automatic Transmission
Front Instrument Panel Cupholders (Bucket Seats) — Automatic Transmission If your new Ram truck is equipped with bucket seats there are three cup holders located on the front of the center console. Cup Holders Bucket Seat UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Front Instrument Panel Cupholders —...
Page 202: Rear Cupholder - Quad Cab - If Equipped
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder — Quad Cab — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience. Rear Cupholder — Mega Cab Mega Cab vehicles are equipped with rear cupholders located in the center armrest.
Page 203: Storage
STORAGE Center Storage Compartment (40–20–40 Seat) — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover.
Page 204: Center Storage Compartment (Bucket Seats)- If Equipped
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 205 storage area into separate compartments. Lift the lower handle on the front of the armrest, and raise the armrest for access to the lower storage bin. On Quad Cab and Mega Cab models the rear of the floor console offers a power outlet, a tip out bin and a rear air duct (Mega Cab Only).
Page 206: Storage And Seats (Quad Cab Models)
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Quad Cab Models) Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat.
Page 207: Storage And Seats (Mega Cab Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Storage and Seats (Mega Cab Models) The Mega Cab models provide additional storage behind the rear seat. To gain access to the Mega Cab rear storage, fold the rear seats to the “kneel position”. (See page 158 for more information.) Push down on the front of the storage compartment handle and lift the storage compartment cover.
Page 208: Plastic Grocery Bag Retainers (Mega Cab Models)
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear storage compartment can be divided into three separate compartments by using the divider doors inside the storage compartment. Mega Cab Rear Storage Dividers Plastic Grocery Bag Retainers (Mega Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
Page 209: Rear Window Features
REAR WINDOW FEATURES Electric Rear Window Defroster and Heated Side view Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature.
Page 210: Sliding Rear Window-If Equipped
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Rear Window—If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat, may be equipped with a folding load floor.
Page 211 WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
Page 212 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Positioning the Load Floor for Storage Access Under the Seat 1.
Page 213: Pickup Box
Load Floor Securing Straps 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 PICKUP BOX Pickup Box Features The pickup box on your new Ram has many features designed for utility and convenience.
Page 214 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
Page 215: Slide-In Campers
There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box.
Page 216 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed. TAILGATE SUPPORT STRAP ATTACHMEN TAILGATE OPEN...
Page 217: Safety Tips
WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks. SAFETY TIPS Transporting Passengers This vehicle is designed to carry passengers in the cab only.
Page 218 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 219 Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation. Check for proper air flow through all defroster ducts. If there are any question regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer Seat Belts Inspect the belt system periodically, checking for cuts,...
Page 220 220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks.
Page 221: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....225 Instrument Cluster ..... . 226 Instrument Cluster Description .
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped ......246 Sales Code RAQ –...
Page 223 Operation Instructions - (CD Mode For CD Audio Play) ... 266 Load/Eject Button (CD Mode For CD Audio Play) ... 267 Notes On Playing MP3 Files .
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna ..... . 279 Reception Quality ..... 279 Remote Sound System Controls —...
Page 225: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 225 INSTRUMENTS AND CONTROLS...
Page 226: Instrument Cluster
226 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 227: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gages This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gages indicate a reading either too high or too low. Examine the gages carefully, and follow the instructions above for each indicated problem. NOTE: When the ignition switch is turned to OFF, the Fuel Gage, Voltmeter, Oil Pressure and Engine Coolant Temperature gages may not show accurate readings.
Page 228 228 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 5. Airbag Indicator Light The indicator lights and remains lit for 6 to 8 seconds when the ignition is first turned on.
Page 229 NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound. 10. Transfer Case Position (See page 316 for more information.) 11. TOW HAUL The TOW HAUL button is located at the end of the gear shift lever.
Page 230 230 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling.
Page 231 NOTE: The odometer/trip odometer Vacuum Fluores- cent Display may also display GASCAP, which indicates that your gas cap is possibly loose or damaged. The Vacuum Fluorescent Display will also display NO- FUSE, which indicates that the IOD fuse is removed from the Integrated Power Module.
Page 232 232 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
Page 233 that the anti-lock portion of the brake system is not functioning and that service is required. See your autho- rized dealer immediately. The ABS light could also illuminate during loss of traction and remain illuminated until the brake pedal is pressed. 20.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL 24. ESP/BAS Warning Lamp – If Equipped The lamp indicates a problem with one or more of the functions of ESP. The yellow “ESP/BAS Warning Lamp” in the instrument cluster comes on when the ignition switch is turned to the “ON”...
Page 235 TCS Indicator Light” becomes illuminated when the ESP-Off button has been pressed or ESP is only partially available. 27. Transmission Oil Temperature Warning Light (Automatic Transmissions Only) This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usage such as trailer towing.
Page 236: Electronic Digital Clock
236 UNDERSTANDING YOUR INSTRUMENT PANEL 31. Door Ajar The door ajar light will illuminate when any door is opened. When the ignition is ON the door ajar light will stay illuminated until the open door is closed. When the ignition is OFF the door ajar light will stay illuminated until the open door is closed or the battery saver feature automatically turns the light off.
Page 237: Radio General Information
RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “ap- parent”...
Page 238: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
238 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature.
Page 239 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 241 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 242: Operation Instructions - Cd Mode
242 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 243 • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player. • This radio does not play discs with MP3 tracks. SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD.
Page 244: Operation Instructions - Auxiliary Mode
244 UNDERSTANDING YOUR INSTRUMENT PANEL RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 245: Operating Instructions - Hands Free Phone - If Equipped
MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. MUTE will display. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers.
Page 246: Operating Instructions - Satellite Radio - If Equipped
246 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
Page 247 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 249 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 250 250 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: 16 Digit-Character Dis- Program Type No program type or un- defined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Foreign_Language Information Jazz News...
Page 251 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 252: Operation Instructions - (Cd Mode For Cd Audio Play)
252 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD MODE for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: Note: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 253: Load/Eject Button (Cd Mode For Cd Audio Play)
SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 254 254 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
Page 255: Notes On Playing Mp3 Files
RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
Page 256 256 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: •...
Page 257 MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 258: Operation Instructions
258 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file.
Page 259 MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the MSG or INFO button once more to return to elapsed time priority mode.
Page 260: Sales Code Rak - Am/Fm/Cassette/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, Video, Mp3, And Wma Capabilities
260 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES ) (If Equipped) Refer to separate Video Entertainment System (VES ) Guide.
Page 261 Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
Page 262 262 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes.
Page 263 Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
Page 264 264 UNDERSTANDING YOUR INSTRUMENT PANEL Country Oldies Soft Nostalgia Jazz Classical Rhythm and Blues Rhythm_and_Blues Soft Rhythm and Blues Foreign Language Foreign_Language Religious Music Religious Talk Personality Public College Unassigned Weather By pressing the SEEK button when the PTY icon is Country displayed, the radio will be tuned to the next frequency Oldies...
Page 265: Operating Instructions - Tape Player
Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the left and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
Page 266: Scan Button
266 UNDERSTANDING YOUR INSTRUMENT PANEL Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press Preset 6.
Page 267: Load/Eject Button (Cd Mode For Cd Audio Play)
compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks and WMA. Inserting Compact Disc(s) CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
Page 268 268 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show LOADING DISC when the disc is loading and “READING DISC” when the radio is reading the disc. LOAD/EJT - Eject Press the LOAD/EJT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal.
Page 269: Notes On Playing Mp3 Files
RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. NOTE: MP3 and WMA Random Play are for file folders only.
Page 270 270 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: •...
Page 271 MPEG Specifi- Sampling Fre- cation quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 272: Operation Instructions
272 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 and WMA Audio Play) SEEK Button (CD Mode for MP3 and WMA Play) Pressing the right side of the SEEK button plays the next file. Pressing the left side of the SEEK button plays the beginning of the file.
Page 273 INFO Button (CD Mode for MP3 Play) Press and INFO button while playing MP3 or WMA disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the INFO button once more to return to elapsed time priority mode.
Page 274: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio With Navigation System
274 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the “Satellite Radio” section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES) (If Equipped) Refer to separate “Video Entertainment System (VES) Guide.” SALES CODE REC —...
Page 275: Operating Instructions - Satellite Radio (If Equipped)
menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
Page 276: System Activation
276 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation NOTE: Your vehicle’s radio must be on and in satellite mode when the activation process takes place. To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com.
Page 277: Selecting Satellite Mode In Ref, Raq, And Rak Radios
ESN/SID Access With RAQ and RAK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID num- bers will display. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
Page 278: Selecting A Channel
278 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
Page 279: Pty Button Seek
one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected.
Page 280: Remote Sound System Controls - If Equipped
280 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls The right hand control is a rocker type switch with a button in the center.
Page 281: Tape Player
Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection.
Page 282: Compact Disc Maintenance
282 UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
Page 283: Radio Operation And Cellular Phones
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio.
Page 284: Heater Only - If Equipped
284 UNDERSTANDING YOUR INSTRUMENT PANEL Heater Only — If Equipped Manual Heating Controls The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Page 285 Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel.
Page 286: Air Conditioning And Heating
286 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating — If Equipped Air Conditioning And Heating Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the outlets selected by the mode control.
Page 287 Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired. This feature allows for recir- culation of interior air only. Air flows through the panel only or through both the panel and floor vents depend- ing on the selected mode (panel vs bi-level).
Page 288 288 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left posi- tion.
Page 289: Air Conditioning With Dual Zone Temperature Control - If Equipped
Air Conditioning with Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle. Dual Zone Control Head UNDERSTANDING YOUR INSTRUMENT PANEL 289 Air Conditioning and Heating Operation To turn on the Air Conditioning, set the fan control at any...
Page 290 290 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recirculate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior. See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air...
Page 291 Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 292 292 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 293: Operating Tips
conditioning system has been on. It is not an indication of a problem with the air conditioning system. Rear Air Duct—Mega Cab Only Mega Cab Rear Air Duct The rear seat will receive air flow in all modes except for Defrost.
Page 294 294 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases turning on the Air-conditioning (pressing the snowflake button) will clear the fog.
Page 295 NOTE: On models equipped with Diesel engines, the idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling. Your air conditioning system is also equipped with an automatic recirculation system. When the system senses a heavy load or high heat conditions, it may use partial Recirculation A/C mode to provide additional comfort.
Page 296: Operating Tips Chart
296 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart...
Page 297 STARTING AND OPERATING CONTENTS Starting Procedures – Gas Engines ... 302 Manual Transmission ....302 Automatic Transmission .
Page 298 298 STARTING AND OPERATING Shifting Procedure - Manually Shifted Transfer Case ......319 Transfer Case Reminder Light .
Page 299 TCS (Traction Control System) – If Equipped With ESP ....345 BAS (Brake Assist System) ....346 Hsa (Hill Start Assist) .
Page 300 300 STARTING AND OPERATING Tire Rotation Recommendations ... . 377 Dual Rear Wheels ..... 379 Fuel Requirements .
Page 301: Starting And Operating
Snowplow ......406 Dodge Ram 1500 Models ....406 Before Plowing .
Page 302: Starting Procedures - Gas Engines
302 STARTING AND OPERATING STARTING PROCEDURES – GAS ENGINES The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! Be sure to turn off the engine if you want to rest or sleep in your car.
Page 303: Normal Starting
Normal Starting Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the START position and release when the engine starts. If the engine fails to start within 10 seconds, turn the key to the OFF position, wait 5 seconds, then repeat the starting procedure.
Page 304 304 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle.
Page 305: After Starting
If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly.
Page 306: Engine Block Heater - If Equipped
306 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle.
Page 307: Automatic Transmission With Overdrive
WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 308 308 STARTING AND OPERATING WARNING! Never use Park position on an automatic transmis- sion as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park).
Page 309 “N” Neutral Shift to Neutral when the vehicle is standing for pro- longed periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. NOTE: Towing the vehicle, coasting, or driving, with the transmission in neutral (N) position, can cause severe damage to the transmission.
Page 310 310 STARTING AND OPERATING • vehicle speed is above approximately 30 mph (48 km/h); • the “TOW HAUL O/D OFF” switch has not been activated; • transmission has reached normal operating tempera- ture. NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature.
Page 311 When To Use “TOW HAUL” and “O/D OFF” Modes Tow Haul O/D Off Switch When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the “TOW HAUL O/D OFF” button once to select TOW HAUL.
Page 312: Manual Transmission
312 STARTING AND OPERATING Torque Converter Clutch A feature, designed to improve fuel economy, has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation in the upper gears.
Page 313: Manual Transmission - 6 Speed (G56)
Truck models with manual transmission are equipped with a clutch interlocking ignition system. The clutch pedal must be fully depressed to start the vehicle. Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelera- tor pedal.
Page 314: Recommended Vehicle Shift Speeds
314 STARTING AND OPERATING To shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop. Reverse has a “crash-through” lockout feature. Move the shift lever from the Neutral position straight across, in one swift motion, and down into Reverse.
Page 315: Recommended Shift Speeds
You should use first gear when starting from a standing position. Damage to the clutch can result from starting in 2nd or 3rd gear. Use each gear in numerical order – do not skip a gear. To shift into Reverse, come to a complete stop. Depress the clutch and pause briefly to allow the gear train to stop.
Page 316: Four-Wheel- Drive Operation - If Equipped
FOUR-WHEEL- DRIVE OPERATION — IF EQUIPPED Four-Wheel-Drive Dodge Ram Trucks are equipped with either a Manually Shifted transfer case or an Electroni- cally Shifted transfer case. See the operating instructions for your transfer case, located within this section.
Page 317: Manually Shifted Transfer Case Operating Information/Precautions
Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides 4 mode positions - 2 (rear)- wheel-drive high range, 4-wheel-drive high range, neu- tral, and 4-wheel-drive low range. This transfer case is intended to be driven in the 2-wheel- drive position (2H) for normal street and highway con- ditions such as dry hard surfaced roads.
Page 318 318 STARTING AND OPERATING NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
Page 319: Shifting Procedure - Manually Shifted Transfer Case
4-Wheel-Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Neutral - Disengages both the front and rear driveshafts from the powertrain.
Page 320: Transfer Case Reminder Light
320 STARTING AND OPERATING vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral) or depress the clutch on a manual transmission.
Page 321: Electronically Shifted Transfer Case Operating Information/Precautions (5 Position Switch)-If Equipped
Electronically Shifted Transfer Case Operating Information/Precautions (5 Position Switch)—If Equipped 5 Position Switch This is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. STARTING AND OPERATING 321 This Electronically Shifted transfer case provides 5 mode positions: 2 wheel drive (2WD), 4WD AUTO, 4WD HI, Neutral and 4WD Lo.
Page 322 322 STARTING AND OPERATING When additional traction is required, the transfer case 4WD HI and 4WD LO positions can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4WD Control Switch to the desired position - see Shifting Procedure section for specific shifting instructions.
Page 323 NOTE: The transfer case Neutral (N) position is selected by depressing the recessed button located on the lower left hand corner of the 4WD Control Switch. The transfer case Neutral (N) position is to be used for recreational towing only. See the Recreational Towing section for specific procedures on shifting into and out of Neutral (N).
Page 324 324 STARTING AND OPERATING The “SERVICE 4WD” warning light monitors the electric shift 4WD system. If this light remains on after engine start up or illuminates during driving, it means that the 4WD system is not functioning properly and that service is required.
Page 325 WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 326: Shifting Procedure - Electronically Shifted Transfer Case
326 STARTING AND OPERATING 4WD LO 4 Wheel Drive Low Range - Low speed 4 wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only.
Page 327 light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five (5) seconds and try the shift again. NOTE: If all the requirements to select a new transfer case position have been met, the current position indica- tor light will turn OFF, the selected position indicator...
Page 328 328 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). Alternate Procedure 1.
Page 329: Electronically Shifted Transfer Case Operating Information/Precautions (4 Position Switch)-If Equipped
Electronically Shifted Transfer Case Operating Information/Precautions (4 Position Switch)—If Equipped Transfer Case Switch STARTING AND OPERATING 329 This is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. This Electronically Shifted transfer case provides 4 mode positions: 2 (rear) wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral.
Page 330 330 STARTING AND OPERATING in the 4HI and 4LO positions on dry hard surfaced roads may cause increased tire wear and damage to the drive- line components. Neutral Button NOTE: The transfer case Neutral (N) position is selected by depressing the recessed button located on the lower left hand corner of the 4WD Control Switch.
Page 331 If One or More Shift Conditions are not Met 1. The indicator light for the current position will remain 2. The newly selected position indicator light will con- tinue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met.
Page 332 332 STARTING AND OPERATING When operating your vehicle in 4LO, the engine speed is approximately three times that of the 2WD or 4HI positions at a given road speed. Take care not to over- speed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and circumference on each wheel.
Page 333: Shifting Procedure - Electronically Shifted Transfer Case
4 Wheel Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 4 Wheel Drive Low Range - Low speed 4 wheel drive. Locks the front and rear driveshafts together.
Page 334 334 STARTING AND OPERATING light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five (5) seconds and try the shift again.
Page 335 Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. USE EITHER OF THE FOLLOWING PROCEDURES: Preferred Procedure 1. With engine RUNNING, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2.
Page 336: Limited-Slip Differential - If Equipped
336 STARTING AND OPERATING NOTE: If your are leaving your vehicle stored for longer than 21 days, refer to the section on “Vehicle Storage.” LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels.
Page 337: Driving On Slippery Surfaces
DRIVING ON SLIPPERY SURFACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 338: Parking Brake
338 STARTING AND OPERATING NOTE: After off-road usage, particularly in sand or mud, inspect the underside of the vehicle for accumu- lated dirt at the propeller shaft, axles, U-joints, brake rotors and calipers. Use a hose to clean off any accumulation of dirt or mud. Check the exhaust system and all exposed components for any sign of damage.
Page 339 Parking Brake Release Be sure the parking brake is firmly set when parked and the gear shift lever is in the PARK position. When parking on a hill you should apply the parking brake before placing the gear shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of PARK.
Page 340: Brake System
340 STARTING AND OPERATING When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine off), the...
Page 341: Rear Wheel Anti-Lock Brake System - Rwal
also contribute to the noise condition. Repeated or con- tinuous noises during braking may be an indication that the brake linings are worn and in need of replacement. Rear Wheel Anti-Lock Brake System — RWAL The Anti-lock Brake System provides increased vehicle stability and brake performance under most braking conditions.
Page 342 342 STARTING AND OPERATING The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. When you are in a severe braking condition involving use of the Anti-lock Brake System, you will experience some pedal drop as the vehicle comes to a complete stop.
Page 343: Power Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 344: Electronic Brake Control System
344 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
Page 345: Tcs (Traction Control System) - If Equipped With Esp
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 346: Bas (Brake Assist System)
346 STARTING AND OPERATING BAS (Brake Assist System) ESP Off Button Location The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes.
Page 347: Hsa (Hill Start Assist)
WARNING! • BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydro- planing.
Page 348 348 STARTING AND OPERATING WARNING! If the clutch pedal (manual vehicles only) remains depressed during the application of the throttle, the HSA will disengage allowing the vehicle will roll down the incline. This could cause a collision with another vehicle or object. To avoid this, do not apply throttle while depressing the clutch pedal until you are ready to release the clutch.
Page 349 HSA on Automatic Vehicles The system will work in reverse and all forward gears on vehicles equipped with an automatic transmission. The system will not activate if the vehicle is placed in neutral. HSA on Manual Vehicles The system will work in reverse, forward gears, and neutral on manual transmission equipped vehicles.
Page 350 350 STARTING AND OPERATING WARNING! If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
Page 351: Erm (Electronic Roll Mitigation)
3. With the engine running, the brake applied, and the clutch out, rotate the steering wheel 180° counter- clockwise from center. 4. Press ESP button four times within twenty seconds. The “ESP/TCS Indicator Light” should appear and dis- appear four times. 5.
Page 352: Esp (Electronic Stability Program)
352 STARTING AND OPERATING WARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
Page 353 ESP/TCS Indicator Light The “ESP/TCS Indicator Light” located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active. The “ESP/TCS Indicator Light” also flashes when TCS is active. If the “ESP/TCS Indicator Light”...
Page 354 354 STARTING AND OPERATING The ESP system has multiple operating modes depend- ing on vehicle type – Two Wheel Drive (2WD) or Four Wheel Drive (4WD). 4WD vehicles may be equipped with either a four mode position (2WD/Neutral/4HI/ 4LO) transfer case or a five mode position (2WD/Auto/ Neutral/4H/4LO) transfer case.
Page 355 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch. Once the situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily depressing the “ESP Control Switch”.
Page 356 356 STARTING AND OPERATING mph (56 km/h) the ESP system shuts off. ESP is off at low vehicle speeds sao that it will not interfere with off-road driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h). The “ESP/ TCS Indicator Light”...
Page 357: Multi Displacement System (Mds) - 5.7L Engine Only
ESP or BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
Page 358: Tire Safety Information
358 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 359 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 360 360 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 361: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 362: Tire Loading And Tire Pressure
362 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
Page 363 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading...
Page 364 364 STARTING AND OPERATING passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (since 5 x 150 = 750, and 1400 – 750 = 650 lbs.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
Page 365 STARTING AND OPERATING 365...
Page 366: Tires - General Information
366 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 367: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear pat- terns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 368 368 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 369: Radial-Ply Tires
loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail.
Page 370: Compact Spare Tire - If Equipped
370 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 371: Limited Use Spare - If Equipped
Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
Page 372: Tread Wear Indicators
372 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
Page 373: Life Of Tire
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
Page 374: Alignment And Balance
374 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of un- approved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
Page 375: Supplemental Tire Pressure Information - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION – IF EQUIPPED A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 376 376 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Ram 4X2 trucks. NOTE: The use of class “S” chains is permitted on 1500 Ram Trucks with P245/70R17 tires only.
Page 377: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 378 378 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 379: Dual Rear Wheels
Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. STARTING AND OPERATING 379 CAUTION! 3500 Dual Rear Tires have only one approved direc-...
Page 380: Fuel Requirements
380 STARTING AND OPERATING FUEL REQUIREMENTS All engines (except 5.7L engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and perfor- mance when using high quality unleaded “regular” gasoline having an octane rating 3.7L/4.7L of 87. The routine use of premium gasoline Engines is not recommended.
Page 381: Reformulated Gasoline
Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. We strongly support the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components.
Page 382: Materials Added To Fuel
382 STARTING AND OPERATING life and reduce emission system performance. We recom- mend that gasolines free of MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gaso- line retailer whether or not his/her gasoline contains MMT.
Page 383: Carbon Monoxide Warnings
• When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock. If spark knock persists, lighten the load, or engine piston damage may result. •...
Page 384: Adding Fuel
384 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 385 CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled.
Page 386: Flexible Fuel- (Fleet Vehicles Only)
386 STARTING AND OPERATING cluster. Tighten the gas cap until a “clicking” sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started.
Page 387: Fuel Requirements
WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
Page 388: Starting
388 STARTING AND OPERATING Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F. In the range of 0°F to 32°F, you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up.
Page 389: Vehicle Loading
VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN).
Page 390 390 STARTING AND OPERATING Tire Size The tire size on the Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire size listed.
Page 391 Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
Page 392: Trailer Towing
392 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) 6500 LBS. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible.
Page 393 Gross Trailer Weight (GTW) The gross trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its loaded and ready for operation condition. The recom- mended way to measure GTW is to put your fully loaded trailer on a vehicle scale.
Page 394 394 STARTING AND OPERATING that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck.
Page 395 STARTING AND OPERATING 395 Weight Distributing Hitch System Improper Adjustment of Weight Distributing System Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin.
Page 396: Trailer Hitch Classification
396 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to...
Page 397: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 398: Towing Requirements
398 STARTING AND OPERATING • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
Page 399 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 400 400 STARTING AND OPERATING 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements —...
Page 401 − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 402: Towing Tips
402 STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 4 - Pin Connector 7- Pin Connector Towing Tips...
Page 403 If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “TOW HAUL”...
Page 404: Trailer Towing Mirrors - If Equipped
404 STARTING AND OPERATING Towing Tips — Cooling System To reduce potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. −...
Page 405 STARTING AND OPERATING 405 Blindspot Mirror Trailer Towing Position...
Page 406: Snowplow
Snowplow Prep Packages are available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow. Dodge Ram 1500 Models NOTE: Do not use Dodge Ram 1500 Models for snow- plow applications. WARNING! On 1500 Models, snowplows, winches, and other aftermarket equipment should not be added to the front end of your vehicle.
Page 407: Before Plowing
Snowplow Model Prep Package Availability For Detailed Information Visit www.dodge.com or refer to the Current Dodge Truck Body Builders Guide. 1. The 1500 models are NOT available for snowplow applications. 2. The maximum number of occupants in the truck should not exceed two.
Page 408: Over The Road Operation With Snowplow Attached
408 STARTING AND OPERATING 5. Cargo capacity will be reduced by the addition of options or passengers, etc. The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver, passengers, options, and cargo, must not exceed either the Gross Vehicle Weight (GVWR) or Gross Axle Weight (GAWR) ratings.
Page 409: Methods For Removing Snow
Methods For Removing Snow Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility.
Page 410: Recreational Towing (Behind Motorhome, Etc.)
410 STARTING AND OPERATING Keep all snowplow electrical connections and battery terminals clean and free of corrosion. When plowing snow, to avoid transmission and driv- etrain damage, the following precautions should be ob- served. • Operate with transfer case in 4L when plowing small or congested areas where speeds are not likely to exceed 15 mph (24 km/h).
Page 411 CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the Manual Shift and Electronic Shift transfer cases must be shifted into Neutral (N) for recreational towing. Automatic transmissions must be placed in P (Park) position for recreational towing.
Page 412 412 STARTING AND OPERATING 8. Release brake pedal for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with the transmission in Drive (D). 10. Shut OFF the engine and place the ignition key to the unlocked OFF position.
Page 413 5. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual transmissions. 6. Shift transfer case lever to desired position. 7. Shift automatic transmission into P (Park). WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the N (NEUTRAL) position without first fully engaging the parking brake.
Page 414 414 STARTING AND OPERATING CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in Neutral (N) before recreational towing to prevent damage to internal parts. 1. Bring vehicle to a complete stop. 2.
Page 415 15. Attach vehicle to tow vehicle with tow bar. 16. Release parking brake. NOTE: Items 1 through 5 are requirements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until the 4 seconds elapses and the shift has been completed.
Page 416 416 STARTING AND OPERATING 3. Turn the ignition key to the ON position, but do not start the engine. 4. Depress the brake pedal. 5. Shift automatic transmission to Neutral (N) or depress clutch on manual transmission. 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 1 second.
Page 417 WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission position.
Page 418: Equipment Identification Plate
418 STARTING AND OPERATING EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood inner surface. The following information about your vehicle is dis- played on this plate: Model, Wheelbase, Vehicle Identifi- cation Number, Truck Order Number, and code numbers with descriptions of all production and special equip- ment on the truck as shipped from the factory.
Page 419: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....420 Jacking And Tire Changing ....421 Jack Location .
Page 420: Hazard Warning Flasher
420 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. Hazard Light Warning Switch To engage the Hazard Warning lights, depress the button on the top of the steering column.
Page 421: Jacking And Tire Changing
JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 422 422 WHAT TO DO IN EMERGENCIES Removal (1500 Standard Cab/Quad Cab Vehicles) Jack Cover The jack and jack tools are stored under the front passenger seat. Lift the tab and slide the plactic cover forward for access. Jack Wing Bolt Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
Page 423: Reinstalling The Scissors-Type Jack And Tools (1500 Models)
WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience, abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 424 424 WHAT TO DO IN EMERGENCIES 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows), and tie to the jack using the tie straps. Tying Bag to Jack with Straps Folding Flap and Rolling Bag...
Page 425 WHAT TO DO IN EMERGENCIES 425 Jack and Tools Tied Jack Wing Bolt 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt.
Page 426: Jacking Instructions
426 WHAT TO DO IN EMERGENCIES JACKING INSTRUCTIONS Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Page 427: Tire Changing Procedure
It is recommended that you stow the flat or spare to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
Page 428 428 WHAT TO DO IN EMERGENCIES • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel.
Page 429 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. WHAT TO DO IN EMERGENCIES 429 3.
Page 430 430 WHAT TO DO IN EMERGENCIES 1500 4X4 Jacking Location • For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. 4X2 Jacking •...
Page 431 • For 2500/3500 4x4 series trucks, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front.
Page 432 432 WHAT TO DO IN EMERGENCIES • Connect the jack tube extension and wheel wrench. Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. NOTE: If the 2500/3500 bottle jack will not lower by turning the dial (thumb wheel) by hand, it may be neces- sary to use the jack drive tube in order to lower the jack.
Page 433 WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. 7. Install wheel center cap and remove wheel blocks. Do not install chrome or aluminum wheel center caps on the spare wheel.
Page 434 434 WHAT TO DO IN EMERGENCIES CAUTION! Use a back and forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. CAUTION! The rear hub caps on the dual rear wheel has two pry off notches.
Page 435 Slots in the wheels will assist in properly orienting the inner and outer wheels. Align these slots when assem- bling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the ground when tightening to insure wheel centering and maximum wheel clamping.
Page 436 436 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved.
Page 437 wheel. The nuts should then be tightened to recom- mended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved. Recommended torques are shown in the following chart.
Page 438: Hoisting
438 WHAT TO DO IN EMERGENCIES HOISTING A conventional floor jack may be used at the jacking locations, refer to the graphics that show jacking loca- tions. However, a floor jack or frame hoist must never be used on any other parts or the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle...
Page 439 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immedi- ately with large quantities of water.
Page 440 440 WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result.
Page 441 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! • You should not try to start your vehicle by push- ing or towing.
Page 442: Freeing A Stuck Vehicle
442 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between DRIVE and REVERSE (automatic transmissions) and between 1st and RE- VERSE (manual transmissions), while applying slight pressure to the accelerator.
Page 443: Towing A Disabled Vehicle
WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing.
Page 444: 2-Wheel- Drive Vehicles
444 WHAT TO DO IN EMERGENCIES NOTE: The Transfer Case must be in the neutral posi- tion, and the transmission must be in Park (Automatic Transmission), or in gear (Manual Transmission) to tow a 4WD vehicle with one end of the vehicle raised. The manufacturer recommends towing with all wheels OFF the ground.
Page 445: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment— 3.7L/4.7L ... 448 Engine Compartment— 5.7L ....449 Onboard Diagnostic System (OBD II) ..450 Loose Fuel Filler Cap Message .
Page 446 446 MAINTAINING YOUR VEHICLE Maintenance Free Battery ....461 Air Conditioner Maintenance ... . . 463 Power Steering —...
Page 447 Noise Control System Required Maintenance & Warranty For 3500 2-Wheel Drive And 4-Wheel Drive Models Over 10,000 Lbs. (4 535 Kg) Gross Vehicle Weight Rating....483 Appearance Care And Protection From Corrosion .
Page 448: Engine Compartment- 3.7L/4.7L
448 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 3.7L/4.7L...
Page 449: Engine Compartment- 5.7L
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 5.7L...
Page 450: Onboard Diagnostic System (Obd Ii)
450 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Vehicles equipped with California emissions controls have a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
Page 451: Emissions Inspection And Maintenance Programs
message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
Page 452: Replacement Parts
452 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL light will blink for approximately 5 sec- onds and then remain on until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station.
Page 453: Dealer Service
DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 454: Engine Oil
454 MAINTAINING YOUR VEHICLE could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
Page 455 Change Engine Oil Road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: • Day or night temperatures are below 32°F (0°C). •...
Page 456 456 MAINTAINING YOUR VEHICLE Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner, the crankcase inlet air cleaner and the crankcase ventilation system.
Page 457: Engine Oil Filter
operating temperatures. These engine oils improve low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, see the Engine Compartment illustration in this section. Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used.
Page 458: Drive Belts - Check Condition And Tension
458 MAINTAINING YOUR VEHICLE quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are a high quality oil filter and are recommended. Drive Belts — Check Condition and Tension Belt tension is controlled by means of an automatic tensioner.
Page 459: Engine Air Cleaner Filter
Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”.
Page 460 460 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 461: Emission-Related Components
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle.
Page 462 462 MAINTAINING YOUR VEHICLE WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 463: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.
Page 464: Power Steering - Fluid Check
464 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 465: Steering Linkage - Inspection
The ball joints originally supplied with the vehicle are permanently lubricated at the factory and do not require service. However, if the seals on the ball joints are damaged, the joints should be replaced. Serviceable replacement ball joints are available. Front suspension ball joints should be replaced only by a qualified service technician using tools specially de- signed for this purpose.
Page 466: Front Prop Shaft Lubrication - 2500/3500 (4X4) Models
466 MAINTAINING YOUR VEHICLE Front Prop Shaft Lubrication — 2500/3500 (4X4) Models Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate Maintenance Schedule for your vehicle (Schedule “A” and “B”). Use Mopar type MS-6560 (lithium based grease), or equivalent. Front Driveshaft Grease Fitting Body Lubrication Locks and all body pivot points, including such items as...
Page 467: Windshield Wiper Blades
Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accu- mulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
Page 468: Exhaust System
468 MAINTAINING YOUR VEHICLE After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield. Mopar All Weather Windshield Washer Solution, used with water as directed on the container, aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim.
Page 469: Cooling System
CRACKING DUE TO WEATHERING DOES NOT AD- VERSELY AFFECT PERFORMANCE. If, however, exces- sively deep localized cracks are present, or any part of the exhaust system abnormally contacts the underbody hard- ware, the isolator and/or hanger should be replaced. Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator.
Page 470 470 MAINTAINING YOUR VEHICLE drain from the coolant recovery bottle. DO NOT RE- MOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 471 Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 472 472 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine.
Page 473 When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 474: Hoses And Vacuum/Vapor Harnesses
474 MAINTAINING YOUR VEHICLE • Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 475: Brake System
Brake System Power Disc Brakes (front and rear) Disc brakes do not require adjustment; however, several hard stops during the break-in period are recommended to seat the linings and wear off any foreign material. Brake And Power Steering Hoses When the vehicle is serviced for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 476 476 MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder — Brake Fluid Level Check The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system...
Page 477: Clutch Hydraulic System
WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
Page 478 478 MAINTAINING YOUR VEHICLE This inspection should be made with the vehicle in a level position. The fluid level should be even with the bottom of the fill hole for the Manufacturer’s C205F HD Front Axles. The fluid level should be 5/8” (16 mm) below on 9 1/4”...
Page 479: Transfer Case
Transfer Case Fluid Level Check This fluid level can be checked by removing the filler plug. The fluid level should be to the bottom edge of the filler plug hole with the vehicle in a level position. Lubricant Selection Refer to Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 480: Automatic Transmission
480 MAINTAINING YOUR VEHICLE Automatic Transmission Selection Of Lubricant Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recom- mended fluid. CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
Page 481 To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brake pedal.
Page 482: Front And Rear Wheel Bearings
The use of transmission sealers should be avoided, since they may adversely affect seals. Front and rear Wheel Bearings Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement. In some instances, these bearings will...
Page 483: Noise Control System Required Maintenance & Warranty For 3500 2-Wheel Drive And 4-Wheel Drive Models Over 10,000 Lbs. (4 535 Kg) Gross Vehicle Weight Rating
“purge” excess grease and the bearing will look slightly wet. This is normal. Periodic inspection for excess play is recommended. Rear Wheel Bearings — Manufacturer’s Axles These bearings are normally considered permanently lubricated. Cleaning and repacking is required only when axle shafts are removed or in case of extreme water or dust contamination.
Page 484 484 MAINTAINING YOUR VEHICLE should be performed anytime a malfunction is observed or suspected. Proper maintenance of the entire vehicle will help the effectiveness of the noise control systems. Air Cleaner Assembly Inspect air cleaner housing for proper assembly and fit. Make certain that the air cleaner is properly positioned and the cover is tight.
Page 485 ENGINE COOLING SYSTEM • Removal or rendering inoperative the fan clutch. • Removal of the fan shroud. Noise Emission Warranty The manufacturer warrants that this vehicle as manufac- tured by the manufacturer, was designed, built and equipped to conform at the time it left the manufacturers control with all applicable U.S.
Page 486 486 MAINTAINING YOUR VEHICLE Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES KILOMETERS Exhaust system-inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED BY PERFORMED AT MILES KILOMETERS Exhaust system-inspect...
Page 487: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 488 488 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove.
Page 489 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner. •...
Page 490 490 MAINTAINING YOUR VEHICLE Interior Care Use Mopar Total Clean to clean fabric upholstery and carpeting. Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth.
Page 491 Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial household- type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna.
Page 492: Fuses (Integrated Power Module)
492 MAINTAINING YOUR VEHICLE FUSES (INTEGRATED POWER MODULE) An integrated Power Module is located in the engine compartment near the battery. This center contains car- tridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 493 Cavity Cartridge Mini Description Fuse Fuse 20 Amp Power Outlet Console Yellow 20 Amp Cabin Compartment Yellow Node (CCN) Door Locks/Brake Trans- mission Shift Inter- lock (BTSI) 20 Amp Spare Yellow 15 Amp Spare Blue 20 Amp Power Sunroof Yellow 10 Amp Occupant Classifica- tion Module (OCM)/...
Page 494 494 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 20 Amp Ignition Off Draw Yellow (IOD)-Cabin Com- partment Node (CCN)/Radio/Under Hood Lamp/Wireless Control Module (WCM)/Satellite Digi- tal Audio Receiver (SDARS)/Hands Free Module (HFM) 30 Amp Electric Brake Pink 25 Amp Power-Battery Natural RWAL/ABS Module...
Page 495 Cavity Cartridge Mini Description Fuse Fuse 10 Amp Engine Control Mod- ule (ECM)/Wireless Control Module (WCM)/HVC 20 Amp Subwoofer Amplifier Blue (SRT-10 Only) 10 Amp Power Mirror 20 Amp Brake Switch/Center Yellow High Mount Stop Lamp (CHMSL) 40 Amp Power Seats Green 10 Amp Power Run/Start-...
Page 496 496 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 25 Amp Audio_Amplifier Natural 15 Amp Spare Blue 20 Amp Power Outlet IP Yellow 10 Amp Sunroof/Seatbelt Ten- sioner 20 Amp Cigar Lighter Yellow 25 Amp Spare Natural 30 Amp Diesel PCM (Diesel Pink Only) Description...
Page 497: Vehicle Storage
VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (I.O.D.) fuse located in the Integrated Power Module, located in the engine compartment.
Page 498: Replacement Light Bulbs
498 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Overhead Console Lights ....TS 212-2 Dome Light......7679 NOTE: For lighted switches, see your dealer for replace- ment instructions.
Page 499: Bulb Replacement
BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two (2) bolts from the front of the head- light housing.
Page 500 500 MAINTAINING YOUR VEHICLE 3. Remove the plug from the inner fender well and remove the nut through the access hole. Inner Fender Plug Rear Headlight Housing Nut Access 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
Page 501 NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly. Headlight Removal MAINTAINING YOUR VEHICLE Bulb Removal 5. Unlock and pull connector straight from the base of the headlight halogen bulb.
Page 502: Fog Lights
502 MAINTAINING YOUR VEHICLE 7. Remove housing from vehicle with headlight halogen bulb in housing. 8. Twist the headlight halogen bulb headlight bulb from the housing. 9. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb. 10.
Page 503: Tail, Stop, Turn And Backup Lights
2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and hous- ing. MAINTAINING YOUR VEHICLE Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. Removing the Two (2) Screws...
Page 504 504 MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. Pulling Housing From Body 3. Rotate the bulb socket counterclockwise to remove from the housing.
Page 505 MAINTAINING YOUR VEHICLE 4. Pull bulb straight out of socket. 5. Reverse Procedure to install bulb and housing. Place the two raised blocks passed the body. Pulling Bulb From Socket Sliding Raised Blocks Past Body...
Page 506: Center High-Mounted Stoplight (Chmsl) With Cargo Light
506 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn desired bulb socket ⁄...
Page 507: Cab Top Clearance Lights - If Equipped
4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High Mount Stop Lamp 5. Reverse procedure for installation of bulbs and hous- ing. MAINTAINING YOUR VEHICLE Cab Top Clearance Lights — If Equipped 1.
Page 508 508 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the light 3. Pull the bulb straight from it’s socket and replace. assembly.
Page 509: Tailgate Id Lights (Dual Rear Wheels) - If Equipped
MAINTAINING YOUR VEHICLE Tailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the rear.
Page 510: Rear Light Bar Id Marker (Dual Rear Wheel) - If Equipped
510 MAINTAINING YOUR VEHICLE 2. Turn socket ⁄ turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. Rear Light Bar ID Marker (Dual Rear Wheel) – If Equipped 1.
Page 511: Side Marker Lights (Dual Rear Wheels)
3. Pull the bulb straight out from the socket. 4. Reverse procedure for installation of bulbs and hous- ing. Side Marker Lights (Dual Rear Wheels) MAINTAINING YOUR VEHICLE 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender. 3.
Page 512: Fluids And Capacities
512 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 3.7L/4.7L 5.7L 1500 Shortbed Models 1500 Longbed Models 1500 Shortbed Models 2500 Shortbed Models 2500 Longbed Models 3500 Shortbed Models 3500 Longbed Models Engine Oil (with filter) 3.7L Engine V-6 (SAE 5W-30, API Certified) 4.7L Engine V-8 (SAE 5W-30, API Certified) U.S.
Page 513 5.7L Engine V-8 (SAE 5W-20, API Certified). For trucks operating under a gross combined weight rating less than 14,000 lbs. 5.7L Engine V-8 (SAE 5W-30, API Certified). For 2500/ 3500 trucks operating under a gross combined weight rating greater than 14,000 lbs. Cooling System 3.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent.
Page 514: Fluids, Lubricants And Genuine Parts
514 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 3.7/4.7L Engine Oil 5.7L Engine Oil (For trucks operat- ing under a gross combined weight rating less than 14,000 lbs.) 5.7L Engine Oil (For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs.) Engine Oil Filter...
Page 515: Chassis
Chassis Component Automatic Transmission Transfer Case NVG 246 Automatic Transfer Case Only Manaul Transmission Fluid (G238) Manual Transmission Fluid (G-56) Clutch Linkage 1500 Model Front Axle (4X4) 1500 Model Rear Axle 2500/3500 Model Front and Rear Axle Synthetic, GL-5 SAE, 75W-90 or equivalent. Limited-Slip 10.5/11.5 inch Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts.
Page 517: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..518 Maintenance Schedules – Gas Engines ..518 Schedule “B” ......521 Schedule “A”...
Page 518: Emission Control System Maintenance
518 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 519 • Heavy Loading. • Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B”...
Page 520 520 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 521: Schedule "B
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 522 522 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stow- age. Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 523 Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stow- age. Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 524 524 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stow- age. Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 525 Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Flush and replace engine coolant.
Page 526 526 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stow- age. Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 527 Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Change front and rear axle fluid (4X4).
Page 528 528 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Flush and replace engine coolant, if not replaced at 60 months.
Page 529 Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 530 530 SCHEDULE “B” Miles (Kilometers) Inspect PCV valve, replace as necessary. ** Inspect auto tension drive belt and replace if re- quired (3.7L/4.7L/5.7L). Flush and replace engine coolant if not done at 102,000 miles (170 000 km). Inspect automatic transmission fluid, add if nec- essary.
Page 531 Miles (Kilometers) Change engine oil and engine oil filter at inter- val shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 532 532 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Check spare tire for proper pressure and correct stowage. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Drain and refill transfer case fluid (4X4).
Page 533 Miles (Kilometers) Drain and refill automatic transmission fluid and change main sump and spin-on cooler return filter (if equipped)*. Flush and replace engine coolant if not replaced at 120,000 miles (193 000 km). * This applies only if the vehicle is used for frequent trailer towing, snowplowing, fleet vehicle or commercial service.
Page 534: Schedule "A
534 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 535 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only.
Page 536 536 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stow- age. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Check transfer case fluid level (4X4). Lubricate Front Drive Shaft Fitting (2500/3500, 4X4).
Page 537 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill transfer case fluid (4X4). Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Flush and replace engine coolant, if not replaced at 60 months. Flush and replace engine coolant if not replaced at 102,00 miles (164 000 km/h).
Page 538 538 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill transfer case fluid (4X4). Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Flush and replace engine coolant, if not replaced at 120,000 miles (193 000 km).
Page 539 Miles (Kilometers) [Months] Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV Valve, replace as necessary. ** ** This maintenance is recommended by the manufac- turer to the owner, but not required to maintain the emissions warranty.
Page 541: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......542 Prepare For The Appointment .
Page 542: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 543 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 544 544 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 545: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 546: Publication Order Forms
546 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 547: Department Of Transportation Uniform Tire Quality Grades
Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 548: Temperature Grades
548 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- mance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Page 549 INDEX...
Page 550 550 INDEX Adding Fuel ......384 Adjustable Pedals ..... . . 174 Air Cleaner, Engine (Engine Air Cleaner Filter) .
Page 551 Ball Joints ......464 Battery ....... 461 Emergency Starting .
Page 552 552 INDEX Cellular Phone ......126 Center High Mounted Stop Light ... . 506 Center Lap Belts .
Page 553 Cruise Control (Speed Control) ....175 Cup Holder ......199 Customer Assistance .
Page 554 554 INDEX Tow Hooks ......442 Towing ......443 Emission Control System Maintenance .
Page 555 Starting ......388 Flooded Engine Starting ....303 Fluid, Brake .
Page 556 556 INDEX Voltmeter ......227 Gear Ranges ......307,314 General Information .
Page 557 Infant Restraint ....60,61,99,100 Inflation Pressure Tires ....375 Inside Rearview Mirror .
Page 558 558 INDEX Courtesy/Reading ..... 179 Cruise ......236 Daytime Running .
Page 559 Lug Nuts ......432 Lumbar Support ......152 Maintenance .
Page 560 560 INDEX Odometer ......230,235 Trip ......230,235 Off-Pavement Driving (Off-Road) .
Page 561 Door Locks ......27 Mirrors ......123 Outlet (Auxiliary Electrical Outlet) .
Page 562 562 INDEX Remote Keyless Entry (RKE) ....20 Remote Sound System (Radio) Controls ..280 Remote Starting System ....24 Replacement Tires .
Page 563 Selection of Coolant (Antifreeze) ..470,514 Sentry Key (Immobilizer) ....15 Service Assistance ..... . . 542 Service Contract .
Page 564 564 INDEX Power ......343,464 Wheel Lock ......15 Wheel, Tilt .
Page 565 Radial ......369 Replacement ......373 Rotation .
Page 566 566 INDEX Fluid ....... 515 Maintenance ..... . . 479,480 Manual .
Page 567 Windows ......31 Power ....... 31 Rear Sliding .
Page 568 NOTES...

This manual is also suitable for:

2007 ram 1500 2007 ram 2500 2007 ram 3500

Dodge 2007 DR Ram Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge 2007 DR Ram

Summary of Contents for Dodge 2007 DR Ram