WEG CFW-09 User Manual page 248

Terminal XC4
1
2
PTC
3 DGND (DI8)
4 DGND


R L 500
5 DO1
6 COMMOM


R L 500
7 DO2
8 24 Vdc
9
10 SREF
11 A-LINE
12 B-LINE
13 AI4 +
14 AI4 -
rpm 15 AGND
16 AO3
17 AGND
A
18 AO4
19
20 COM 1
Figure 8.1 – XC4 terminal block description (EBA board complete)
CHAPTER 8 - CFW-09 OPTIONS AND ACCESSORIES
Factory Default Function
NC Not connected
Motor Thermistor Input 1 - PTC1
(P270 = 16 refer to figure 6.33). As DI
DI8
normal refer to P270 - figure 6.34.
Motor Thermistor Input 2 - PTC2
(P270 = 16 refer to figure 6.33). As DI
normal P270 - figure 6.34.
0 V reference of the 24 Vdc source
Transistor output 1: Not Used
Common point for Digital Input DI7
and Digital Outputs DO1 and DO2
Transistor Output 2: Not Used
Power Supply for the digital inputs/
outputs
DI7 Isolated Digital Input: Not used
Reference for RS-485
RS-485 A-LINE (-)
RS-485 B-LINE (+)
Analog input 4: Frequency Reference
Program P221 = 4 or P222 = 4
0 V Reference for Analog Output
(internally grounded)
Analog output 3: Speed
0 V Reference for Analog Output
(internally grounded)
Analog Output 4: Motor Current
Avaliable to be connected to an external
+ V
power supply to energise the encoder
repeater output (XC8)
0 V reference of the external power supply
ENCODER CONNECTION: Refer to item 8.2.
INSTALLATION
The EBA board is installed on the CC9 control board, secured with spacers
and connected via terminal blocks XC11 (24 V) and XC3.
NOTE!
For the CFW-09 Size 1 Models (6 A, 7 A, 10 A and 13 A/220-230 V and 3.6 A,
4 A, 5.5 A and 9 A/380-480 V) the plastic cover must be removed to install the
EBA board.
Mounting Instructions:
1. Set the board configuration via S2 and S3 dip switches (Refer to table 8.2);
2. Carefully insert terminal block XC3 (EBA) into the female connector XC3
of the CC9 control board. Check that all pins fit in the XC3 connector;
Specifications
Actuation 3k9 Release: 1k6
Min. resistance: 100 
Reference to DGND (DI8) through a
249  resistor.
Grounded via a 249  resistor
Isolated, open collector, 24 Vdc, 50 mA
max., required board (RL)  500 
Isolated, open collector, 24 Vdc, 50 mA
max., required board (RL)  500 
24 Vdc ± 8 %. Isolated,
Capacity: 90 mA
Min. high level: 18 Vdc
Max. low level: 3 Vdc
Max. Voltage: 30 Vdc
Input Current.: 11 mA @ 24 Vdc
Isolated RS-485 serial Port
Differential analog input programmable
on P246: -10 V to +10 V
or (0 to 20) mA / (4 to 20) mA
lin.: 14 bits (0.006 % of full scale range)
Impedance: 40 k [-10 V to +10 V]
500  [(0 to 20) mA / (4 to 20) mA]
Analog outputs signals:
-10 V to +10 V
Scales: refer to P255 and P257.
lin.: 14 bits (0.006 % of ± 10 V range)
Required board (RL)  2 k
External power supply: 5 V to 15 V
Consumption: 100 mA @ 5 V
Outputs not included.
249