Xerox DocuPrint N2025 Service Manual page 269

Novel Bin PS - Novell Menu setting to enable/disable the Novell binary mode of PostScript.
Novell Enabled - Menu setting in the Novell menu to enable the Novell protocol. This item is
common between the Ethernet and Token Ring Menus.
Novell Menu - Menu selection to invoke the "Novell Menu." The Novell Menu allows the user to
modify Novell parameters.
Novell Mode - Menu setting for the PServer mode for the Novell protocol.
Novell PDL - Menu setting for the default emulation for the Novell protocol.
Output Offset - Menu setting for the default mode of the Offset function used in PCl and Post-
script. OFF indicates all pages are output to the same position. ON causes all pages within a
job to be output to the same position, which job alternating in offset position.
Orientation - Menu setting for the default orientation used in PCl. PostScript does not use this
parameter.
Output Dest - Menu setting for the default paper output destination used in PCL and Post-
Script.
Output Time-out - System menu setting to determine whether the printer will select an alter-
nate bin when the selected output bin becomes full.
Page Policy - System Menu setting to allow the printer to automatically select an alternate
paper type or paper size if the requested paper size or type is not installed. This is used by
both PostScript and PCL. If the requested paper is not installed, the printer will prompt the user
to load the requested paper. If the requested paper is not loaded before the time specified by
"Page Timeout" below, then another paper size or type will be used based on this setting,
ignoring either the size requested, the type requested or both. Trays are searched in the order
defined in the "Tray Sequence" item in the Tray menu.
Paper Size - Menu setting for the default paper size.
Paper Type - Menu setting for the default paper Type used in Postscript and PCL.
Parallel PDL - Menu setting for the default emulation for the Parallel port.
Parallel Menu - Menu selection to invoke the Parallel menu.
Password Menu - Menu selection to invoke the "Password Menu." The Password Menu allows
the user to enter a four-digit password to enable printing of secure or proof jobs previously sent
to the printer and stored in the hard disk.
PCL Font List - Menu selection to print a list of PCL fonts currently loaded.
PCL Menu - Menu selection to invoke the "PCL Menu."
Pitch - Menu setting for the pitch when the default font already selected is a scalable fixed pitch
font.
Initial Issue
DocuPrint N2025/N2825
Point Size - Menu setting in PCL for the point size when the default font already selected is a
scalable proportional spaced font.
Policy Time-out - Menu setting associated with "Page Policy" above. The value of this setting
determines how long the printer will wait before taking the action defined by the setting of
"Page Policy."
Polling Interval - Menu setting for the interval (in seconds) at which the PServer issues polling
requests for assigned queues.
Port Enable - Menu setting to enable or disable the Parallel, USB or Serial ports. When "on"
(enabled) it will be included in port switching sequence.
Port Time-out - Menu setting for the time-out for each port. When there is no activity on a port
for a time equal to the time-out then the data stream will be switched to take data from any
other port that has been active. This also causes an implicit job end such as Control D in Post-
Script or <ESC> E in PCL, and invokes the emulation functions associated with this action
(e.g., formfeed, reset. etc.).
Power Saver - System Menu setting to control the idle period before low power mode is acti-
vated.
Print PS Errors - Menu setting in System Menu to control the use of the built in error handler
or debugger.
Print Quantity - System Menu setting for the number of times each page is printed (uncol-
lated). This is usually overridden by the job stream.
Primary Server - Novell menu setting to set the name of the primary file server.
PServer Name - Novell menu setting to set the name of the PServer for this printer.
PS Font List - Menu selection to print a list of the fonts available in PostScript, including resi-
dent fonts and fonts stored on the hard disk.
Reset Menu - Main Menu selection to invoke the Reset menu. The Reset Menu does not
appear in the normal menus list. The Reset menu appears in the menu list if the printer is pow-
ered on while holding down the "On-line" and "Enter" keys.
Resolution - System menu setting to select the default resolution in PostScript, PCL5e and
PCLXL emulations.
Restart Printer - Menu setting to re-boot the printer as if the power was cycled, but bypassing
power on diagnostics. All NVM parameters are reloaded into the current configuration. All net-
work interfaces are re-initialized to their Power On state. The display indicates the same
sequence of messages as seen during a normal power-on sequence, with the exception of the
Power On diagnostic messages.
Serial Menu - Menu selection to invoke the Serial menu.
Serial PDL - Menu setting for the default emulation for the Serial port.
02/2000
6-37
General Procedures / Information
GP 3.4