Xerox DocuPrint N2025 Service Manual page 26

Comments On LIne Message
Duplex Unit Fail or
Removed
Offset Bin Fail
Power Off/On
2000 Sheet Feeder Tray 2 Failure
installed as Tray 2 Power Off/On
2000 Sheet Feeder Tray 3 Failure
installed as Tray 3 Power Off/On
Paper Size Jam
Open Rear Cover
Insert Tray 1
Insert Tray 2
Insert Tray 3
Load Tray 1
Load Tray 2
Load Tray 3
Load MBF
Remove Output
from St. Bin
Remove Output
from Offset Bin
Toner Low
Memory Failure
Power Off/On
Status Indicator Repair Analysis Procedures
Error Code Table
Table 1 Error Code Table
Fault History Entry Diagnostic Message
E9-1 E9:Duplex Fail
E9-2 E-9:OCT Fail
E9-3 E-9:HCF Fail
E9-3 E-9:HCF Fail
EO:HCF Elevator
PSE-1 Paper Size Error
C3:Tray 1 Error
C3: Tray 2 Error
C3: Tray 3 Error
C5:Tray 1 Empty
C5:Tray 2 Empty
C5:Tray 3 Empty
C5:MBF Empty
C5: Top Tray Full
C5:OCT Tray Full
J5:Toner Low
ESS-M N/A
02/2000
Error Description
Duplex module removed while power is
on.
OCT removed while power is on.
2000 Sheet Feeder removed while power
is on.
2000 Sheet Feeder removed while power
is on.
1. 2000 Sheet Feeder elevator did not
reach home position within the pre-
scribed time.
2. Paper level sensor on when 2000
Sheet Feeder Tray is Opened.
There is a conflict between the size of
the paper, which is detected by the Size
Switches, and the length of paper the
printer detects by the length of time the
Registration Sensor is actuated.
Tray 1 is not detected in printer. (all paper
size switches not actuated)
Tray 2 is not detected in printer. (all paper
size switches not actuated)
Tray 3 is not detected in printer. (all paper
size switches not actuated)
Tray 1 is out of paper
Tray 2 is out of paper
Tray 3 is out of paper
MBF is out of paper
Top Tray is declared full when 5 prints are
delivered to the top tray after the Full
Stack sensor is actuated.
5 prints are delivered to the top tray after
the OCT Full Stack sensor is actuated.
Toner Low is detected after 10 prints
while toner sensor is on.
Controller memory has failed (32 me on
board).
2-8
Action
Reinstall Duplex Module
Go to RAP 60
Reinstall OCT
Go to RAP 71
Reinstall HCF
Go to RAP 66
Reinstall HCF
Go to RAP 66
Open and close 2000 Sheet
Feeder paper tray.
Correct the mismatch
Go to RAP 22
Install Tray 1
Go to RAP 4
Install Tray 2
Go to RAP 4
Install Tray 3
Go to RAP 4
Load paper into Tray 1
Go to RAP 5
Load paper into Tray 2
Go to RAP 5
Load paper into Tray 3
Go to RAP 5
Load paper into MBF
Go to RAP 5
Empty Top Tray
Go to RAP 6
Empty OCT Tray
Go to RAP 67
Replace Print Cartridge
Go to RAP 14
Go to RAP 23
Power Off/On
Remove Options
Replace System Controller
PWB (REP 8.1)
Go to RAP 12
Initial Issue
DocuPrint N2025/N2825