Danfoss VLT AQUA Drive FC 202 Operating Manual page 168

Operating Guide | VLT® AQUA Drive FC 202
FC 202
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 525 V) [A]
Continuous (at 575/690 V) [A]
Maximum number and size of cables per phase
2
- Mains [mm (AWG)]
- Mains with disconnect [mm
- Mains with fusible disconnect [mm
- Mains with contactor [mm
2
- Motor [mm (AWG)]
Drive module power loss at 600 V [W]
Drive module power loss at 690 V [W]
Drive efficiency (2)
Output frequency [Hz] (4)
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
PHF overtemperature trip [°C (°F)]
dU/dt filter overtemperature trip [°C (°F)]
Sine-wave filter overtemperature trip [°C (°F)]
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These values are based on a typical motor
efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimensioning of drive cooling. If the switching frequency is higher than the default
setting, the power losses can increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/
knowledge-center/energy-efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficiency class, see the Ambient Conditions
section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses.
4
If using an output filter, the output frequency is limited further. See the Motor Output (U, V, W) section.
Table 85: Electrical Data, Mains Supply 3x525–690 V AC
FC 202
High/normal overload
High overload=150% or 160% torque for a duration of 60 s.
Normal overload=110% torque for a duration of 60 s.
Typical shaft output at 550 V [kW]
168 | Danfoss A/S © 2018.10
2
(AWG)]
2
(AWG)]
2
(AWG)]
(1) (2) (3)
(1) (2) (3)
N450 N500
376 448 409
378 448 408
454 538 490
381 453 413
366 434 395
4x120 (4x250 mcm) 4x120 (4x250 mcm)
4x120 (4x250) 4x120 (4x250)
4x120 (4x250) 4x120 (4x250)
4x120 (4x250) 4x120 (4x250)
4x120 (4x250) 4x120 (4x250)
4989 6062 5419
4920 5939 5332
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
150 (302) 150 (302)
150 (302) 150 (302)
150 (302) 150 (302)
N630 N710
HO NO HO
450 500 500
Specifications
N560
498 498 568
498 498 568
598 598 681
504 504 574
482 482 549
4x120 (4x250 mcm)
4x120 (4x250)
4x120 (4x250)
4x120 (4x250)
4x120 (4x250)
6879 6833 8076
6715 6678 7852
0.98
0–590
110 (230)
80 (176)
150 (302)
150 (302)
150 (302)
N800
NO HO NO
560 560 670
AQ262141056213en-000101 / 130R0882