Danfoss VLT AQUA Drive FC 202 Operating Manual page 162

Operating Guide | VLT® AQUA Drive FC 202
FC 202
- Mains with disconnect [mm
- Mains with fusible disconnect [mm
- Mains with contactor [mm
2
- Mains [mm (AWG)]
Drive module power loss at 400 V [W]
Drive module power loss at 460 V [W]
Drive efficiency (2)
Output frequency [Hz] (4)
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
PHF overtemperature trip [°C (°F)]
dU/dt filter overtemperature trip [°C (°F)]
Sine-wave filter overtemperature trip [°C (°F)]
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These values are based on a typical motor
efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimensioning of drive cooling. If the switching frequency is higher than the default
setting, the power losses can increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/
knowledge-center/energy-efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficiency class, see the Ambient Conditions
section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses.
4
If using an output filter, the output frequency is limited further. See the Motor Output (U, V, W) section.
Table 80: Electrical Data, Mains Supply 3x380–480 V AC
FC 202
High/normal overload
High overload=150% or 160% torque for a duration of 60 s.
Normal overload=110% torque for a duration of 60 s.
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Typical shaft output at 480 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload) (at 400 V) [A]
Continuous (at 460/480 V) [A]
Intermittent (60 s overload) (at 460/480 V) [A]
162 | Danfoss A/S © 2018.10
2
(AWG)]
2
(AWG)]
2
(AWG)]
(1) (2) (3)
(1) (2) (3)
N200 N250
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
3093 4116 4039
2872 3569 3575
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
150 (302) 150 (302)
150 (302) 150 (302)
150 (302) 150 (302)
N355 N400
HO NO HO
315 355 355
450 500 500
355 400 400
E5h E5h
600 658 658
900 724 987
540 590 590
810 649 885
Specifications
N315
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
5137 5005 6674
4566 4458 5714
0.98
0–590
110 (230)
80 (176)
150 (302)
150 (302)
150 (302)
N450
NO HO NO
400 400 450
600 550 600
500 500 530
E5h
745 695 800
820 1043 880
678 678 730
746 1017 803
AQ262141056213en-000101 / 130R0882