Danfoss VLT AQUA Drive FC 202 Operating Manual page 167

Operating Guide | VLT® AQUA Drive FC 202
FC 202
- Mains with disconnect [mm
- Mains with fusible disconnect [mm
- Mains with contactor [mm
2
- Motor [mm (AWG)]
Drive module power loss at 600 V [W]
Drive module power loss at 690 V [W]
Drive efficiency (2)
Output frequency [Hz] (4)
Heat sink overtemperature trip [°C (°F)]
Control card overtemperature trip [°C (°F)]
PHF overtemperature trip [°C (°F)]
dU/dt filter overtemperature trip [°C (°F)]
Sine-wave filter overtemperature trip [°C (°F)]
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These values are based on a typical motor
efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimensioning of drive cooling. If the switching frequency is higher than the default
setting, the power losses can increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/
knowledge-center/energy-efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficiency class, see the Ambient Conditions
section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses.
4
If using an output filter, the output frequency is limited further. See the Motor Output (U, V, W) section.
Table 84: Electrical Data, Mains Supply 3x525–690 V AC
FC 202
High/normal overload
High overload=150% or 160% torque for a duration of 60 s.
Normal overload=110% torque for a duration of 60 s.
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [A]
Danfoss A/S © 2018.10
2
(AWG)]
2
(AWG)]
2
(AWG)]
(1) (2) (3)
(1) (2) (3)
N250 N315
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
2x185 (2x350 mcm) 2x185 (2x350 mcm)
3012 3723 3642
3123 3851 3771
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
150 (302) 150 (302)
150 (302) 150 (302)
150 (302) 150 (302)
N450 N500
HO NO HO
315 355 315
400 450 400
355 450 400
E5h E5h
395 470 429
593 517 644
380 450 410
570 495 615
AQ262141056213en-000101 / 130R0882 | 167
Specifications
N400
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
2x185 (2x350 mcm)
4465 4146 5028
4614 4258 5155
0.98
0–590
110 (230)
80 (176)
150 (302)
150 (302)
150 (302)
N560
NO HO NO
400 400 450
500 500 600
500 500 560
E5h
523 523 596
575 785 656
500 500 570
550 750 627