Quantum ATL StackLink™ Installation Instructions, 6421009-07 A01, September 2003, Made in USA. Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose.
Installing the Rack Mount Shelves Determining the Position of the Shelves in the Rack... 20 Installing the Shelves... 22 Installing the ATL M1500 Rack Mount Shelves ... 22 Installing the ATL M2500 Rack Mount Shelves ... 30 ATL StackLink™ Installation Instructions Contents xiii...
Page 4
Configuring the Library ...84 SCSI Import/Export Elements ...85 Tape Drive SCSI IDs ...85 Library SCSI Settings ...85 Testing the Library Robotics...86 Appendix A Library Size Library Size ...89 Library Size Calculation Examples ...90 Library Size in Mixed Stacks...92 ATL StackLink™ Installation Instructions...
Page 5
Appendix B SCSI Element Addressing Overview... 95 Option Settings and Their Effect on SCSI Element Addressing ... 98 Auto-Clean Option ... 98 Import/Export Option ... 98 SCSI Element Addressing in Multiple Library Stacks... 103 ATL StackLink™ Installation Instructions Contents...
Page 7
Shuttle Assembly... 16 Figure 11 Routing the Belt ... 16 Figure 12 Connecting the Ribbon Cable ... 17 Figure 13 Installing the Shuttle Assembly... 18 Figure 14 Example of Full and Half U Mounting Positions ... 21 ATL StackLink™ Installation Instructions Figures...
Page 8
Installing a Tape Drive in an ATL M2500 Library ...53 Labeling Tape Cartridges ...57 Setting the Write-Protect Switch (DLT and SDLT Cartridges) ...58 Setting the Write-Protect Switch (LTO Cartridges) ...58 Magazine Release Button...59 Inserting DLT Cartridges into a Magazine ...60 ATL StackLink™ Installation Instructions...
Page 13
Installing the rack mount shelves • Installing the library modules in the rack • Installing tape drives in the library modules • Installing safety blanking panels • Preparing and inserting tape cartridges • Cabling the multiple library stack ATL StackLink™ Installation Instructions Preface xiii...
Page 14
Cautions indicate potential hazards to equipment and are included to prevent damage to equipment. Warnings indicate potential hazards to personal safety and are included to prevent injury. ATL StackLink™ Installation Instructions Shelves, explains how to install Stack, explains how to...
Page 15
Rack Mount Conversion Instructions ATL M-Series Tape Drive Installation Instructions ATL M-Series Software Interface Guide ATL StackLink™ Installation Instructions Preface Description This document explains how to service the ATL M1500 library, including: • Understanding error codes • Using built-in diagnostic checks to troubleshoot library problems •...
Page 16
Unpacking Instructions ATL M-Series Installation Guide ATL M-Series User’s Guide ATL StackLink™ Installation Instructions Description This document explains how to remove and replace a tape drive in an ATL M-Series library. This document explains how to remove, package for shipment, and replace an ATL M1500 library chassis.
Page 17
Robotic Hand Removal and Replacement Instructions 6423012 ATL M2500 Library GUI Assembly Replacement Instructions ATL StackLink™ Installation Instructions Preface Description This document explains how to service the ATL M2500 library, including: • Understanding error codes • Using built-in diagnostic checks to troubleshoot library problems •...
Page 18
M-Series Drive Brick Replacement Instructions Quantum ATL M2500 Bezel/Doors/Winged Window Replacement Instructions ATL StackLink™ Installation Instructions Description This document explains how to upgrade the power supply in an ATL M-Series library. This document explains how to convert a rack mounted ATL M2500 to a deskside library.
Page 19
To comment on existing documentation send e-mail to: doc-comments@quantum.com Quantum Home Page Visit the Quantum home page at: http://www.quantum.com Customer Support The Quantum Customer Support Department provides a 24-hour help desk that can be reached at: North/South America: Asia/Pacific Rim: Europe/Middle East/Africa: ATL StackLink™ Installation Instructions...
Page 20
Asia/Pacific Rim: Europe/Middle East/Africa: Send e-mail for the Customer Support Department to: North/South America: Asia/Pacific Rim: Europe/Middle East/Africa: ATL StackLink™ Installation Instructions (949) 725-2176 (International Code) +61 7 3839 0955 (International Code) + +44 (0) 1256 848777 Go to http://www.quantum.com/...
• Make sure you have the necessary tools for the installation (see Required • Prepare the rack for the installation (see Installing the StackLink StackLink Kit Tools). ATL StackLink™ Installation Instructions Chapter 1 Contents). Preparing the Rack).
The following tools are required to install the StackLink: Required Tools • Flat blade screwdriver • No. 2 POZIDRIV • Metric Allen ® screwdriver ® wrenches, sizes M4 and M6 ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink Preparing for the StackLink Installation Quantity Provided...
Fewer than 3 ATL M2500 library modules, allow 40U of space between the top and bottom mounting tray assemblies. • 3 ATL M2500 library modules, allow 40.5U of space between the top and bottom mounting tray assemblies. ATL StackLink™ Installation Instructions...
Rack Rails and 2). Install the caged nuts on the back of the rack rails, facing Note: the interior of the rack. Caged nuts Flat blade screwdriver ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink Preparing for the StackLink Installation...
Top mounting tray position If you are installing 3 ATL M2500 library modules in the rack, do not put caged nuts in these locations Bottom mounting tray position BACK OF RACK Top mounting tray position Bottom mounting tray position ATL StackLink™ Installation Instructions...
Do not over-tighten the screws. You need to be able to Note: extend or retract the rear support arms slightly as you install the top mounting tray assembly. ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink Installing the Top Mounting Tray Assembly figure...
If the rack has widely spaced mounting holes, it may not Note: be possible to use all four screws to secure the rear flanges. If this is the case, one screw per side at the rear is acceptable. ATL StackLink™ Installation Instructions REAR...
Position the .5U panel (PN 215941) at the front of the bottom mounting tray assembly and secure it using the five nuts you removed in the previous step. ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink figure...
Position the front and rear flanges of the bottom mounting Note: tray assembly outside of the rack rails. FRONT ATL StackLink™ Installation Instructions step 2 REAR...
If the rack has widely spaced mounting holes, it may not Note: be possible to use all four screws to secure the rear flanges. If this is the case, one screw per side at the rear is acceptable. ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink...
Page 32
Chapter 1 Installing the StackLink Installing the Carriage/Counterweight Assembly Figure 7 Installing the Carriage/ Counterweight Assembly Counterweight Belt ATL StackLink™ Installation Instructions Carriage Shuttle extrusion...
Page 33
5 Snap the end of the umbilical chain onto the bottom of the carriage (see figure 6 Connect the end of the umbilical cable to the socket on the carriage connection board (see figure ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink...
Chapter 1 Installing the StackLink Installing the Carriage/Counterweight Assembly Figure 8 Connecting the Umbilical Cable to the Bottom of the Carriage ATL StackLink™ Installation Instructions Umbilical cable Screw Carriage Umbilical chain Umbilical cable...
(see Figure 9 Inserting the Motor Assembly into the Vertical Shuttle Assembly These two holes align with oles in the motor assembly ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink Installing the Motor Assembly figure...
3 Route the belt connecting the counterweight and the carriage over the guide roller and past the motor/pulley belt retainer on the motor assembly (see Figure 11 Routing the Belt figure 10). Motor assembly screw Vertical rail assembly figure 11). ATL StackLink™ Installation Instructions Countersink screws (YS42038)
Insert the ribbon cable connector through the rectangular hole at the top of the motor plate. Connect the ribbon cable connector to the socket on the control board. Motor plate ATL StackLink™ Installation Instructions Chapter 1 Installing the StackLink Rectangular hole...
Now that the StackLink is installed, proceed to the next chapter to install the rack mount shelves. figure Tighten these screws to finger-tightness only. You will Note: finish securing the StackLink after you have installed libraries in the rack. (SHOWN OUTSIDE OF RACK) REAR ATL StackLink™ Installation Instructions 13). FRONT...
For information about how the library firmware calculates library size and assigns SCSI element addresses, see appendix A, Library Size, SCSI Element Addressing, ATL StackLink™ Installation Instructions Chapter 2 Installing the on page 89 and appendix B, on page 95.
ATL M2500 rack mount shelves can be installed in either a full U or a half U position (the bottom of the rack mount shelf may be aligned with either the bottom or the middle of a U). ATL StackLink™ Installation Instructions...
U. This position can be mounting bracket aligns with the used for ATL M2500 rack mount bottom of the corresponding U. This shelves only. position can be used for either ATL M1500 or ATL M2500 rack mount shelves ATL StackLink™ Installation Instructions...
ATL M1500 Rack Mount Shelves Checking the Contents of the Rack Mount Kit Table 2 any items are missing, contact Quantum (see page xix). Installing the ATL M2500 Rack Mount on page 30 Read the shelf installation instructions thoroughly. Failure to use the designated inserts, screws, and clamps could result in the library falling from the rack.
Button head socket screw M6 x 12 Countersink hex socket screw M4 X 10 LG Button head socket screw M5 x 12 Button head socket screw 10-32 UNC x 0.5 ins M5 spire nut ATL StackLink™ Installation Instructions Installing the Shelves Qty.
Page 44
(see figure Tighten the nuts to finger-tightness only. You need to be Note: able to retract and extend the assembled shelves slightly. column of table ATL StackLink™ Installation Instructions table column of table 3 column of table Left Shelf/Slots 16).
29.125 in. - 31.50 in. (740 mm - 800 mm) 31.50 in. - 33.875 in (800 mm - 860 mm) 33.875 in. - 36.25 in. (860 mm - 920 mm) ATL StackLink™ Installation Instructions Installing the Shelves Right Shelf Shelf Slots Extender Slots A &...
Some of the inserts have either no head or a head that has Note: a smaller diameter than the thread; these need to be left protruding by about 1/8 in. (3 mm). The inserts with heads should be tightened fully. Inserts ATL StackLink™ Installation Instructions Installing the Shelves...
Position a shelf clamp (PN 213467) on the front left rack rail. The bottom of the shelf clamp should be flush with the bottom of the shelf. Secure the shelf clamp to the rack rail using an M4 countersink screw (PN YS42038). ATL StackLink™ Installation Instructions...
The universal rack mount kit contains screws and nuts for Note: many different types of rack. You will have many of these screws and nuts left over after installing the rack mount shelves and library. ATL StackLink™ Installation Instructions Installing the Shelves...
This section explains how to install the ATL M2500 rack mount shelves. Installing the ATL M2500 Rack Mount Shelves Checking the Contents of the Rack Mount Kit Table 4 any items are missing, contact Quantum (see page xix). Part No. Table 4 Contents, ATL M2500 Universal 213468...
Page 51
3 Assemble the right shelf in the same manner, referring to the column of table Shelf ATL StackLink™ Installation Instructions Chapter 2 Installing the Rack Mount Shelves Installing the Shelves column of table 5...
(740 mm to 800 mm) 31.5 in. to 33.875 in. Long #1 (800 mm to 860 mm) 33.875 in. to 36.25 in. Long #2 (860 mm to 920 mm) ATL StackLink™ Installation Instructions Right Shelf Shelf Slots Extender A & B Long #1 B &...
Some of the inserts have either no head or a head that has Note: a smaller diameter than the thread; these need to be left protruding by about 1/8 in. (3 mm). The inserts with heads should be tightened fully. ATL StackLink™ Installation Instructions...
Expand the shelf so that the inserts on each end of the shelf protrude into the holes in the rack rails and hold the shelf in place. Repeat these steps to install the remaining shelf. through the ATL StackLink™ Installation Instructions Installing the Shelves...
Repeat these steps to install a front shelf clamp on the front right rack rail. Position a rear shelf clamp (PN 215201/01) on the rear left rack rail, aligning the square hole with the middle insert in the shelf flange. ATL StackLink™ Installation Instructions figure 25): figure 26):...
(PN YS42064). Repeat these steps to install a rear shelf clamp on the rear right rack rail. The left and right rear shelf clamps will be oriented Note: differently from one another. ATL StackLink™ Installation Instructions Installing the Shelves...
Page 58
Insert a screw (PN YS42064) through the bottom hole in the front shelf clamp, through the rack rail, and into the bottom hole in the clamp strip. Repeat steps through clamp strip on the right rack rail. ATL StackLink™ Installation Instructions 27): to install the front shelf clamp and...
The universal rack mount kit contains screws and nuts for Note: many different types of rack. You will have many of these screws and nuts left over after installing the rack mount shelves and library. ATL StackLink™ Installation Instructions Installing the Shelves on page 47.
Page 60
Some of the inserts have either no head or a head that has Note: a smaller diameter than the thread; these need to be left protruding by about 1/8 in. (3 mm). The inserts with heads should be tightened fully. ATL StackLink™ Installation Instructions...
Some of the inserts have either no head or a head that has Note: a smaller diameter than the thread; these need to be left protruding by about 1/8 in. (3 mm). The inserts with heads should be tightened fully. ATL StackLink™ Installation Instructions Installing the Shelves...
Secure the front shelf clamp to the rack rail using two M4 countersink screws (PN YS42064). Repeat these steps to install a front shelf clamp on the front right rack rail. ATL StackLink™ Installation Instructions figure 31):...
(PN YS42064). Repeat these steps to install a rear shelf clamp on the rear right rack rail. The left and right rear shelf clamps will be oriented Note: differently from one another. ATL StackLink™ Installation Instructions Installing the Shelves figure 32):...
Insert a screw (PN YS42064) through the bottom hole in the front shelf clamp, through the rack rail, and into the bottom hole in the clamp strip. ATL StackLink™ Installation Instructions 33):...
The universal rack mount kit contains screws and nuts for Note: many different types of rack. You will have many of these screws and nuts left over after installing the rack mount shelves and library. ATL StackLink™ Installation Instructions Installing the Shelves to install the front shelf clamp and...
Page 66
Chapter 2 Installing the Rack Mount Shelves Installing the Shelves ATL StackLink™ Installation Instructions...
This chapter explains how to install the libraries, including: • Installing the Libraries in the Rack • Installing Tape Drives in the Libraries • Installing the Safety Blanking Panels • Preparing and Inserting Tape Cartridges ATL StackLink™ Installation Instructions Chapter 3...
Do not overtighten the rack mount clamp screw. Caution: When the screw begins to feel tight, turn it an additional quarter turn and then stop. through to install any additional library modules. figure 13). ® T-20 screwdriver ATL StackLink™ Installation Instructions...
4 Repeat steps Figure 36 Installing a Tape Drive in an ATL M1500 Library Thumbscrew figure 36). through to install another tape drive, if desired. Tape drive ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Installing Tape Drives in the Libraries...
37). Drive bay 3 is used only if six drives are installed in the library. Drive bay 2 Drive bay 1 Drive bay 6 Drive bay 5 ATL StackLink™ Installation Instructions Drive bay 3 (this drive bay is empty unless a sixth drive is installed) Drive bay 4...
(215982) is used with tape drives on the middle level of the library; the larger plate (215981) is used with tape drives on the bottom level of the library. ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Installing Tape Drives in the Libraries...
Do not attempt to install a sixth drive in the Caution: ATL M2500. This procedure requires specialized software tools available only to Quantum-authorized field service personnel. If a sixth drive is desired, please call one of the following numbers to arrange for a professional installation.
Install the .5U rear safety blanking panel (PN 214217) at the back of the rack, securing the panel with two screws (PN YS41964) and washers (PN YS41731). ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Preparing and Inserting Tape Cartridges...
DLT and SDLT cartridges use non-adhesive labels that slide into a slot at the front of the cartridge. Ensure that the label is fully inserted into the cartridge label slot. LTO cartridges use adhesive labels that adhere to the front of the cartridge. ATL StackLink™ Installation Instructions table 39):...
The orange tab is not visible when the cartridge is write- enabled. Labeling a DLT or SDLT cartridge figure ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Preparing and Inserting Tape Cartridges B C 1 2 3 L 1...
(see To write-enable an LTO cartridge, move the write-protect switch to the left. Write-protect switch Figure 41 Setting the Write-Protect Switch (LTO Cartridges) Slide left Slide right Orange tab figure 41). Write- enabled Write- protected ATL StackLink™ Installation Instructions...
Press the button next the right magazine access door and open the door. Grasping the handle at the front of the right magazine, pull it forward and out of the library. ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Preparing and Inserting Tape Cartridges...
The magazines are designed so that you cannot insert Caution: cartridges incorrectly. Do not try to force the cartridges into the slots. Label Write-protect switch ATL StackLink™ Installation Instructions step Cartridge retaining latch...
Remove the level 2 left magazine (see Reach into the library underneath the level 1 left magazine and pull down on the release latch (see ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Preparing and Inserting Tape Cartridges through figure 44).
Preparing and Inserting Tape Cartridges Figure 45 Release Latch Release latch Figure 46 Removing the Level 1 Left Magazine While holding the release latch, pull the level 1 left magazine forward and out of the library (see ATL StackLink™ Installation Instructions figure 46).
Page 83
Do not force the cartridges into the slots. 6 Insert the magazines into the library, sliding them back until they click into place. 7 Close the magazine access doors. ATL StackLink™ Installation Instructions Chapter 3 Installing the Libraries Preparing and Inserting Tape Cartridges figure 43):...
Page 84
Chapter 3 Installing the Libraries Preparing and Inserting Tape Cartridges ATL StackLink™ Installation Instructions...
2 Daisy chain the control bus as shown in control bus cables provided. 3 Connect the bottom library module in the rack to the I board, using one of the library control bus cables provided. ATL StackLink™ Installation Instructions figure 47, using the library C terminator...
Figure 47 Library Control and StackLink Power Cabling Chapter 4 Cabling the Multiple Library Stack Library control bus terminator ATL StackLink™ Installation Instructions Interlibrary (Control Bus) Cabling Library control bus (daisy chained) This cable completes a loop back to the I2C...
(PN 214090/01, PN 214080/01, or PN 214070/01) from the StackLink motor to the StackLink motor drive on any of the library modules (see Note: figure 48). The library module that is connected to the StackLink motor becomes the GUI master. ATL StackLink™ Installation Instructions...
Page 89
Chapter 4 Cabling the Multiple Library Stack StackLink Motor Connection Figure 48 StackLink StackLink motor Motor Connection StackLink motor drive (Interlibrary cables omitted for clarity) ATL StackLink™ Installation Instructions...
Install the SCSI cabling, referring to Terminator Note: Power. Notice that the host computer is connected to the robotics connector on only one of the library modules. This library module is called the SCSI master. ATL StackLink™ Installation Instructions figure SCSI Cabling Guidelines,...
The number of drives per bus is determined by the data transfer performance of the host and drives. SCSI Bus Connections Chapter 4 Cabling the Multiple Library Stack ATL StackLink™ Installation Instructions SCSI Bus Cabling (Interlibrary and StackLink cabl omitted for clarity) To host adapter (may be...
To connect an ATL M1500 library to AC power, see ATL M1500 Library to AC • To connect an ATL M2500 library to AC power, see ATL M1500 Library to AC Power). option on the GUI Power. Power. ATL StackLink™ Installation Instructions screen. Configuration Connecting an Connecting an...
UL listed and CSA certified. For use in Europe, distribution units must be CE marked. National certifications for other countries depend on local requirements. Power inlet ATL StackLink™ Installation Instructions Power Cabling figure 50) and to the AC...
20A plug. Must be 3 wire grounding plug and wall outlet. • Connect all libraries to one AC distribution unit rated minimum 20A, with a minimum 14AWG 3 wire cord, permanently wired to the electrical supply. ATL StackLink™ Installation Instructions...
UL listed and CSA certified. For use in Europe, distribution units must be CE marked. National certifications for other countries depend on local requirements. figure 51). ATL StackLink™ Installation Instructions Power Cabling figure 51). figure 51) and to the wall...
15A or 20A, with a minimum 14AWG 3 wire cord, and a 15A or 20A plug. Must be three wire grounding plug and wall outlet. ATL StackLink™ Installation Instructions Connect these using a short power cable Connect this...
Page 97
10A, minimum 1.00mm2 <HAR> cord with minimum 10A plug. Must be three wire grounding plug and wall outlet. ATL StackLink™ Installation Instructions Chapter 4 Cabling the Multiple Library Stack 100-120V 50-60Hz supply voltage (USA, Canada, Japan, etc.)
Page 98
Chapter 4 Cabling the Multiple Library Stack Power Cabling ATL StackLink™ Installation Instructions...
Caution: Completing the Installation 53). Power up all the library modules in reasonably quick succession; a long delay in powering up the entire multiple library stack could interfere with library initialization. ATL StackLink™ Installation Instructions Chapter 5 figure 52...
Switches, ATL M2500 To minimize the effects of inrush current, always turn on the library modules using these library power switches instead of using the power switches that may be on the AC distribution unit. ATL StackLink™ Installation Instructions Power switches...
At the bottom of each GUI screen are up to five button labels. These labels indicate the functions of the five push buttons below the GUI. To select a ATL StackLink™ Installation Instructions Chapter 5 Completing the Installation Powering Up the Library...
To complete the library installation, disable any unused drive bays as follows: 1 On the main screen of the library module that contains the unused drive bay, press The GUI displays the figure 56). button: Menu screen (see Menu ATL StackLink™ Installation Instructions Button labels Push buttons figure 57).
Configuration Screen 3 Press the bay is highlighted. 4 Press Config Configuration buttons until the drive ID for the unused drive Down Select ATL StackLink™ Installation Instructions Chapter 5 Completing the Installation Disabling Unused Drive Bays screen (see figure 58).
You must reboot the library before this setting will take Note: effect. through to disable any unused drive bays in other The library must be power cycled before any configuration changes will take effect. ATL StackLink™ Installation Instructions setting is selected. Disabled only if there is no Disabled...
48 Although the Import/Export all of the library modules, it is only functional on the GUI master. ATL StackLink™ Installation Instructions Chapter 5 Completing the Installation Configuring the Library Import/Export on page 69). option appears on the GUIs of...
3 On the GUI main screen of the selected library module, press The GUI displays the Figure 59 Menu Screen 4 Press The GUI displays the screen (see Menu Demo Demo Programs ATL StackLink™ Installation Instructions program to verify that the Demo 5 Menu figure 59). screen (see figure 60).
The StackLink installation is now complete. buttons to select Down Select program starts. The program moves the data cartridge Demo 5 to end the program. Stop ATL StackLink™ Installation Instructions Chapter 5 Completing the Installation Testing the Library Robotics Demo 5...
Page 108
Chapter 5 Completing the Installation Testing the Library Robotics ATL StackLink™ Installation Instructions...
Appendix A Library Size Library Size The firmware reports the library size on the main screen (see figure 61). Figure 61 Main Library size Screen ATL StackLink™ Installation Instructions...
The fixed slot is not included in the calculation of cartridge Note: slots for DLT and SDLT libraries. This is so the library size will calculate to a round number. provides some examples of how the library size is calculated. ATL StackLink™ Installation Instructions Library Size in Mixed Stacks...
ATL M2500 will be filled with an ATL M2500. Thus the gap will be treated as space for 1 ATL M2500 and will be counted as 4 library levels (see ATL StackLink™ Installation Instructions figure 63).
SCSI element address. • Data elements are assigned consecutive addresses, starting at C0h. • Import/export elements are assigned consecutive addresses, starting at B0h. SCSI Element Addressing ATL StackLink™ Installation Instructions Appendix B...
Level 2 right magazine Address DLT/SDLT C0h-C9h CAh-D3h Address DLT/SDLT 6-drive 5-drive Library Library C0h-C9h CAh-D3h D4h-DDh DEh-E7h ATL StackLink™ Installation Instructions Element Type Drive Drive C0h-CBh Data CCh-D7h Data Data 6-drive Element Library Type Drive Drive Drive Drive...
Page 117
SCSI element address. Address DLT/SDLT 6-drive 5-drive Library Library E8h-F1h F2h-FBh FCh-105h 106h-10Fh 110h 111h 112h 113h ATL StackLink™ Installation Instructions Appendix B SCSI Element Addressing Overview 6-drive Element Library Type F0h-FBh Data FCh-107h Data 108h-113h Data 114h-11F Data...
Modules with Auto-Clean disabled will use the tape from the module with Auto-Clean enabled to perform drive cleans. 10). table 11 table 12). ATL StackLink™ Installation Instructions table 9...
Option Settings and Their Effect on SCSI Element Addressing table 13 DLT/SDLT C0h-C8h C9h-D2h Address DLT/SDLT 5-drive 6-drive Library Library ATL StackLink™ Installation Instructions Appendix B SCSI Element Addressing table 14). Address Element Type Drive Drive Import/export C0h-CAh Data CBh-D6h...
Page 120
Address DLT/SDLT 5-drive 6-drive Library Library C0h-C8h C9h-D2h D3h-DCh DDh-E6h E7h-F0h F1h-FAh FBh-104h 105h-10Eh 10Fh 110h 111h 112h ATL StackLink™ Installation Instructions 5-drive 6-drive Element Library Library Type C0h-CAh Data CBh-D6h Data D7h-E2h Data E3h-EEh Data EFh-FAh Data FBh-106h Data...
Page 121
Option Settings and Their Effect on SCSI Element Addressing Address DLT/SDLT B0h-B9h C0h-C9h Address DLT/SDLT 6-drive 5-drive Library Library B0h-B9h C0h-C9h CAh-D3h ATL StackLink™ Installation Instructions Appendix B SCSI Element Addressing Element Type Drive Drive B0h-BBh Import/export C0h-CBh Data Data 6-drive Element Library Type...
Page 122
SCSI element address. Address DLT/SDLT 6-drive 5-drive Library Library D4h-DDh DEh-E7h E8h-F1h F2h-FBh FCh-105h 106h 107h 108h 109h ATL StackLink™ Installation Instructions 6-drive Element Library Type D8h-E3h Data E4h-EFh Data F0h-FBh Data FCh-107h Data 108h-113h Data 114h Data...
Right magazine CAh-D3h CCh-D7h Fixed slot 12Fh Drive 1 Drive 2 Left magazine B0h-B9h Right magazine D4h-DDh Fixed slot 130h ATL StackLink™ Installation Instructions Appendix B SCSI Element Addressing Address Element Type Drive Drive C0h-CBh Data Data 144h Data Drive...
Right magazine C0h-C9h Fixed slot Drive 1 Drive 2 Left magazine CAh-D3h CCh-D7h Right magazine D4h-DDh Fixed slot 12Eh ATL StackLink™ Installation Instructions Appendix B SCSI Element Addressing Address Element Type Drive Drive B0h-BBh Import/export C0h-CBh Data Cleaning ( Auto-...
Need help?
Do you have a question about the ATL StackLink and is the answer not in the manual?
Questions and answers