Table of Contents
Advertisement
Revision
Version
Page 2-2: Added QS845 to block diagram. Page 2-12: Added Table 2-F QS845A
Supplementary Board Specifications. Page 3-6: Added QS845A statement under heading
CPS6000 Controller; added comcode for rectifier slot filler. Page 3-8: Modified table. Page
3- 10: Added supplementary shelf information and 2-shelf kit comcode. Page 5-7: Added
Issue 5
Figure 5-4 for QS845A installation. Page 5-19: Added Figure 5-13 for inter-shelf
connections. Page 6-10: Added QS845A Supplementary Shelf Board section. Page 7-2:
Relocated PFC Fail and Input Fuse in LED table. Page A-16: Added ringer command table.
Page D-1: Added second link to EasyView software.
Changed name from Aux Box to Distribution Module. Page 2-10, Table 2-C: Changed input
current, maximum discharge current and note. Page 2-11, Table 2-D1: Added shutdown
range notes to input voltage ranges. Page 2-12: Added Table 2D-3, QS865A Rectifier
Specifications. Page 3-4: Aux Boxes, Added battery circuit breaker note. Page 3-6,
Rectifiers: Added QS865 Rectifier and comcode. Page 3-7: Revised AC Input Current Table.
Issue 6
Page 3-8: Replaced ac input table. Page 7-1: Changed dead zone upper limit to 180V.
Deleted high-line range for current-limited mode. Changed QS862A initial lower limit
power-up and low-limit shut-down to 180V. Added QS865A description. Page 7-4: Added
50A data to Figure 7-2.
Page 11-1, Table 11-A: Changed first line Rectifier LED.
Manual updated throughout to include Double-Slot Distribution Module and Ringer
information. Page 2-11, 2-12, Updated rectifier specification tables 2-D1, D2, and D3. Page 3-
4: Updated power shelves and distribution modules; Corrected comcode for H569-470
G60A. Page 3-9: Updated Shelf AC Input Current Table. Page 5-12: Moved Discrete Office
Alarm Connector from Appendix E. Added Section 6, AC, Alarm, and Control Cable
Issue 7
Reference Information. Pages 7-4 through 7-6: Added CPS6000 Controller Minimum
Configuration section. Added Section 10, QS820A Ringer. Page C-2, Table C-1, Check
Battery: Included failure of automatic and periodic discharge tests as alarm conditions.
Page C-4, Table C-1, Open String: Changed alarm relay and LED status from PMN to PMJ.
Page C-5, Table C-1, Very Low Float Voltage: Changed alarm relay and LED status from PMN
to PMJ. Added Appendix F Operating Temperature Measurement and Vertical Spacing.
Overview section changed, Table-2A, 2B revised, ordering information – baffle, distribution
module section revised, rectifier section revised to add new rectifier ratings, ringer
description corrections, and shelf ac input table revised. Added external AC distribution
panel, changed view of double slot to show all 4 battery positions. Added External DC
Issue 8
Distribution Panel.
Updated rectifier section to include 500W, 40A rectifiers. Revised figure 8-2 to include all
rectifiers, revised safety section on wires, added 25 and 150 ft cable Ordering code,
removed pigtail Ordering code
Issue 9
Added torque table to shelf installation.
Issue 10
Updated Tables 2-C and 3-A
Issue 11
Removed references to back-to-back lug configurations for battery and load connections
Updated CPS6000 pin-out in Appendix E. Corrected text above Fig 5-11. Removed G161 and
Issue 12
G162 panels
Revised Introduction, System Overview. Updated tables 2-A,B,C,D,and G. Corrected Ringing
Issue 13
Type in Ringer Installation. Added Figure 5-19 Ringer Load Cable Connector Pins.
Page 199
© Copyright 2021 ABB. All rights reserved.
Description of the change
Date Dept./
Init.
Advertisement
Table of Contents
