Mitsubishi Electric 800 Series Instruction Manual page 125

Parameter List
Parameter list (by function group)
Pr.
Pr.
group
Third stall prevention operation
H603 115
frequency
Stall prevention operation level
H610 23
compensation factor at double speed
Stall prevention operation reduction
H611 66
starting frequency
H620 148
Stall prevention level at 0 V input
H621 149
Stall prevention level at 10 V input
Voltage reduction selection during stall
H631 154
prevention operation
H700 810
Torque limit input method selection
H701 812
Torque limit level (regeneration)
H702 813
Torque limit level (3rd quadrant)
H703 814
Torque limit level (4th quadrant)
H704 801
Output limit level
H710 815
Torque limit level 2
H720 816
Torque limit level during acceleration
H721 817
Torque limit level during deceleration
H730 874
OLT level setting
H800 374
Overspeed detection level
H881 690
Deceleration check time
 M: Monitor display and monitor output signal
Parameters regarding the inverter's operating status. These
parameters are used to set the monitors and output signals.
Pr.
Pr.
group
M000 37
Speed display
M001 505
Speed setting reference
M002 144
Speed setting switchover
M020 170
Watt-hour meter clear
M021 563
Energization time carrying-over times
M022 268
Monitor decimal digits selection
Cumulative power monitor digit
M023 891
shifted times
M030 171
Operation hour meter clear
M031 564
Operating time carrying-over times
M040 55
Frequency monitoring reference
M041 56
Current monitoring reference
M042 866
Torque monitoring reference
M043 241
Analog input display unit switchover
M044 290
Monitor negative output selection
M045 1018
Monitor with sign selection
M050 1106
Torque monitor filter
M051 1107
Running speed monitor filter
M052 1108
Excitation current monitor filter
Control circuit temperature signal
M060 663
output level
Operation panel main monitor
M100 52
selection
M101 774
Operation panel monitor selection 1
M102 775
Operation panel monitor selection 2
M103 776
Operation panel monitor selection 3
M104 992
Parameter for manufacturer setting. Do not set.
M200 892
Load factor
Energy saving monitor reference
M201 893
(motor capacity)
Control selection during commercial
M202 894
power-supply operation
M203 895
Power saving rate reference value
M204 896
Power unit cost
M205 897
Power saving monitor average time
Power saving cumulative monitor
M206 898
clear
124
PARAMETERS
Refer
Name
to page
332
332
332
332
332
332
154
154
154
154
154,
190
154
154
154
154
343
180
Refer
Name
to page
345
345
345
347
347
347
347,
365
347
347
357
357
357
402
347,
357
347
347
347
347
390
347
347
347
347
365
365
365
365
365
365
365
Pr.
Pr.
group
M207 899
Operation time rate (estimated value)
M300 54
FM terminal function selection
M301 158
AM terminal function selection
M310 900
FM terminal calibration
M320 901
AM terminal calibration
M321 867
AM output filter
M400 190
RUN terminal function selection
M401 191
SU terminal function selection
M402 192
IPF terminal function selection
M403 193
OL terminal function selection
M404 194
FU terminal function selection
M405 195
ABC1 terminal function selection
M406 196
ABC2 terminal function selection
M410 313

DO0 output selection
M411 314

DO1 output selection
M412 315

DO2 output selection
M413 316

DO3 output selection
M414 317

DO4 output selection
M415 318

DO5 output selection
M416 319

DO6 output selection
M420 320

RA1 output selection
M421 321

RA2 output selection
M422 322

RA3 output selection
M430 157
OL signal output timer
M431 289
Inverter output terminal filter
Output current detection signal
M433 166
retention time
M440 870
Speed detection hysteresis
M441 41
Up-to-frequency sensitivity
M442 42
Output frequency detection
Output frequency detection for
M443 43
reverse rotation
M444 50
Second output frequency detection
M445 116
Third output frequency detection
M446 865
Low speed detection
M460 150
Output current detection level
Output current detection signal delay
M461 151
time
M462 152
Zero current detection level
M463 153
Zero current detection time
Output current detection operation
M464 167
selection
M470 864
Torque detection
M500 495
Remote output selection
M501 496
Remote output data 1
M502 497
Remote output data 2
M510 76
Fault code output selection
Pulse increment setting for output
M520 799
power
M530 655
Analog remote output selection
M531 656
Analog remote output 1
M532 657
Analog remote output 2
M533 658
Analog remote output 3
M534 659
Analog remote output 4
Control terminal option-Encoder pulse
M600 863

division ratio
M601 413

Encoder pulse division ratio
Cumulative pulse clear signal
M610 635

selection
Cumulative pulse division scaling
M611 636

factor
Control terminal option-Cumulative
M612 637

pulse division scaling factor
M613 638

Cumulative pulse storage
Refer
Name
to page
365
357
357
362
362
362
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
370
154,
332
370
382
379
379
379
379
379
379
379
382
382
382
382
382
384
385
385
385
388
389
386
386
386
386
386
391
391
227
227
227
227