Mitsubishi Electric 800 Series Instruction Manual page 127

Parameter List
Parameter list (by function group)
Pr.
Pr.
group
C141 359

Encoder rotation direction
Encoder signal loss detection enable/
C148 376

disable selection
Lq tuning target current adjustment
C150 1002
coefficient
Starting resistance tuning
C182 717
compensation
Starting magnetic pole position
C185 721
detection pulse width
C200 450
Second applied motor
C201 453
Second motor capacity
C202 454
Number of second motor poles
C203 51
Rated second motor current
C204 456
Rated second motor voltage
C205 457
Rated second motor frequency
C206 743
Second motor maximum frequency
C207 744
Second motor inertia (integer)
C208 745
Second motor inertia (exponent)
Second motor auto tuning setting/
C210 463
status
C211 574
Second motor online auto tuning
C220 458
Second motor constant (R1)
C221 459
Second motor constant (R2)
Second motor constant (L1) / d-axis
C222 460
inductance (Ld)
Second motor constant (L2) / q-axis
C223 461
inductance (Lq)
C224 462
Second motor constant (X)
C225 455
Second motor excitation current
Second motor torque current/Rated PM
C226 860
motor current
Second motor induced voltage constant
C230 738
(phi f)
C231 739
Second motor Ld decay ratio
C232 740
Second motor Lq decay ratio
C233 746
Second motor protection current level
Second motor induced voltage constant
C235 1413
(phi f) exponent
Control terminal option-Number of
C240 851

encoder pulses
Control terminal option-Encoder
C241 852

rotation direction
C242 862

Encoder option selection
Control terminal option-Signal loss
C248 855

detection enable/disable selection
Second starting resistance tuning
C282 741
compensation
Second motor magnetic pole detection
C285 742
pulse width
 A: Application parameters
Parameters to set a specific application.
Pr.
Pr.
group
A000 135
Electronic bypass sequence selection
A001 136
MC switchover interlock time
A002 137
Start waiting time
A003 138
Bypass selection at a fault
126
PARAMETERS
Refer
Name
to page
64,
473,
619
446
436
436
436
423
426,
436
426,
436
317,
426,
436
426,
436
426,
436
436
436
436
426,
436,
522
444
426,
436,
522
426
426,
436
426,
436
426
426
426,
436
436
436
436
436
436
64
64
141
446
436
436
Refer
Name
to page
448
448
448
448
Pr.
Pr.
group
Automatic switchover frequency from
A004 139
inverter to bypass operation
Automatic switchover frequency range
A005 159
from bypass to inverter operation
A006 248
Self power management selection
A007 254
Main circuit power OFF waiting time
A100 278
Brake opening frequency
A101 279
Brake opening current
A102 280
Brake opening current detection time
A103 281
Brake operation time at start
A104 282
Brake operation frequency
A105 283
Brake operation time at stop
Deceleration detection function
A106 284
selection
A107 285
Overspeed detection frequency
A108 639
Brake opening current selection
A109 640
Brake operation frequency selection
A110 292
Automatic acceleration/deceleration
A120 642
Second brake opening frequency
A121 643
Second brake opening current
Second brake opening current
A122 644
detection time
A123 645
Second brake operation time at start
A124 646
Second brake operation frequency
A125 647
Second brake operation time at stop
Second deceleration detection function
A126 648
selection
A128 650
Second brake opening current selection
Second brake operation frequency
A129 651
selection
Second brake sequence operation
A130 641
selection
A170 1410
Starting times lower 4 digits
A171 1411
Starting times upper 4 digits
Stop-on contact/load torque high-speed
A200 270
frequency control selection
A201 271
High-speed setting maximum current
A202 272
Middle-speed setting minimum current
A203 273
Current averaging range
A204 274
Current averaging filter time constant
Stop-on contact excitation current low-
A205 275
speed multiplying factor
PWM carrier frequency at stop-on
A206 276
contact
A300 592
Traverse function selection
A301 593
Maximum amplitude amount
Amplitude compensation amount
A302 594
during deceleration
Amplitude compensation amount
A303 595
during acceleration
A304 596
Amplitude acceleration time
A305 597
Amplitude deceleration time
DC brake judgment time for anti-sway
A310 1072
control operation
A311 1073
Anti-sway control operation selection
A312 1074
Anti-sway control frequency
A313 1075
Anti-sway control depth
A314 1076
Anti-sway control width
A315 1077
Rope length
A316 1078
Trolley weight
A317 1079
Load weight
A510 350

Stop position command selection
A511 360

16-bit data selection
Refer
Name
to page
448
448
454
454
457
457
457
457
457
457
457
179,
457,
619
457
457
285,
288,
457
457
457
457
457
457
457
457
457
457
457
462
462
463,
466
466
466
466
466
463
463
469
469
469
469
469
469
471
471
471
471
471
471
471
471
473
473