Mitsubishi Electric 800 Series Instruction Manual page 121

Parameter List
Parameter list (by parameter number)
Pr.
Pr.
group
Home position shift amount lower 4
1285 B183
digits
Home position shift amount upper 4
1286 B184
digits
Travel distance after proximity dog
1287 B185
ON lower 4 digits
Travel distance after proximity dog
1288 B186
ON upper 4 digits
Home position return stopper
1289 B187
torque
Home position return stopper
1290 B188
waiting time
Position control terminal input
1292 B190
selection
1293 B191
Roll feeding mode selection
1294 B192
Position detection lower 4 digits
1295 B193
Position detection upper 4 digits
1296 B194
Position detection selection
1297 B195
Position detection hysteresis width
─ 1298 B013
Second position control gain
1299 G108
─ Second pre-excitation selection
1300 N500
Communication option parameters.
─ to to
For details, refer to the Instruction Manual of the option.
1343 N543
─ 1348 G263
P/PI control switchover frequency
Emergency stop operation
─ 1349 G264
selection
1350 N550
Communication option parameters.
to to
─
For details, refer to the Instruction Manual of the option.
1359 N559
─ 1410 A170
Starting times lower 4 digits
1411 A171
─ Starting times upper 4 digits
Motor induced voltage constant
1412 C135
─
(phi f) exponent
Second motor induced voltage
─ 1413 C235
constant (phi f) exponent
Load characteristics measurement
1480 H520
mode
Load characteristics load reference
1481 H521
1
Load characteristics load reference
1482 H522
2
Load characteristics load reference
1483 H523
3
Load characteristics load reference
1484 H524
4
Load characteristics load reference
1485 H525
5
Load characteristics maximum
1486 H526
frequency
Load characteristics minimum
1487 H527
frequency
1488 H531
Upper limit warning detection width 0 to 400%, 9999
1489 H532
Lower limit warning detection width 0 to 400%, 9999
1490 H533
Upper limit fault detection width
1491 H534
Lower limit fault detection width
Load status detection signal delay
1492 H535
time / load reference measurement
waiting time
1499 E415
─
Parameter for manufacturer setting. Do not set.
120
PARAMETERS
Name Setting range
0 to 9999
0 to 9999
0 to 9999
0 to 9999
0 to 200%
0 to 10 s
0, 1
0, 1
0 to 9999
0 to 9999
0 to 2
0 to 32767
0 to 150 s
0, 1
0 to 400 Hz
0, 1, 10, 11
0 to 9999
0 to 9999
0 to 2, 9999
0 to 2, 9999
0, 1 (2 to 5, 81 to 85)
0 to 400%, 8888,
9999
0 to 400%, 8888,
9999
0 to 400%, 8888,
9999
0 to 400%, 8888,
9999
0 to 400%, 8888,
9999
0 to 590 Hz
0 to 590 Hz
0 to 400%, 9999
0 to 400%, 9999
0 to 60 s
Minimum
setting Initial value
increments
1 0
1 0
1 2048
1 0
0.1% 40%
0.1 s 0.5 s
1 0
1 0
1 0
1 0
1 0
1 0
-1 -1
1 s 25 s
1 0
0.01 Hz 0 Hz
1 0
1 0
1 0
1 9999
1 9999
1 0
0.1% 9999
0.1% 9999
0.1% 9999
0.1% 9999
0.1% 9999
0.01 Hz 60 Hz
0.01 Hz 6 Hz
0.1% 20%
0.1% 20%
0.1% 9999
0.1% 9999
0.1 s 1 s
Refer
to
page
207
207
207
207
207
207
207
207
234
234
234
234
-1
236
599
164
269
462
462
436
436
339
339
339
339
339
339
339
339
339
339
339
339
339