Roland SOLJET Pro III XC-540 Service Notes page 140

SERVICE MENU MOTOR MENU
MOTOR MENU AGING
MOTOR MENU
SERVO LOCK
SERVICE MENU HEATER MENU
HEATER MENU SVC. MODE HEAT.
HEATER MENU
HEATER ADJUST
HEATER MENU
PREHEAT TEMP.
HEATER MENU
HEAT TIMEOUT
HEATER MENU
HEATER CHECK
SERVICE MENU SYSTEM SWITCH
SYSTEM SWITCH PAGE1
SYSTEM SWITCH
PAGE16
AGING SCAN
SCAN NOW AGING
AGING FEED
FEED NOW AGING
AGING BOTH
BOTH NOW AGING
AGING CUTTING
NOW AGING
CUTTING
Servo Motor : LOCKED
SERVO LOCK SERVO LOCK
S: 100 F:
Servo Motor : FREE
SERVO LOCK SERVO LOCK
F: 240 20 F:
SVC.MODE HEAT.
This is to specify ON/OFF of the heater when the machine is started in the Service Mode.
STOP > STOP
HEATER ADJUST PRE
PRE
HEATER ADJUST PRINT
PRINT
HEATER ADJUST DRYER
DRYER
HEATER ADJUST OPTION-DRYER
OPTION-DRYER
PREHEAT TEMP.
Range : 20 to 40
35 C 35 C Default : 30
HEAT TIMEOUT Range : OFF, 10 to 30min.
OFF 10min
Default : 20min.
Print Heater : OFF Print Heater : ON
PRE 25 C PRE
PRINT _ 25 C PRINT
Option Dryer : Not connected
_
DRYER 25 C DRYER
OPT. 25 C OPT.
This menu is to change the functions of the machine. Normally, it is not necessary to change.
PAGE1
Each bit can be selected by [left] and [right] keys and changed by [up] and [down] keys.
00000000
Press [ENTER] to save the settings. There are 16 pages for 8 bits System Switch.
bit #[ 1 2 3 4 5 6 7 8 ]
PAGE1:Bit1
PAGE16
PAGE1:Bit4
00000000
PAGE1:Bit7
bit #[ 1 2 3 4 5 6 7 8 ]
PAGE2:Bit6
PAGE4:Bit7
* All the default of settigs not shown here is "0".
CAUTION : The machine may make unexpected move when the other system switches not shown here are changed.
4-9
SCAN : Aging for Scan Motor.
The Head Carriage runs max. printing width
in Scan direction.
FEED : Aging for Feed Motor.
Grit Roller runs 100mm back and forth.
BOTH : The Head Carriage runs max. printing width
in Scan direction, and at the same time, Grit Roller
runs 100mm back and forth.
CUTTING : The Tool Carriage runs max. printing width
in Scan direction, and at the same time, Grit Roller
runs the half of max. printing width back and forth.
To stop Aging, press [ENTER] key. The Head Carriage returns
back to the capping position, and it returns to the former menu
after the Head is capped.
Make sure not to perform Aging for excessive time when the
Head is filled with ink, in order to prevent the Head from being
damaged by dried ink.
When Aging is performed with ink filled, it runs with performing
the Flushing. No Flushing when ink is not filled.
This menu is to check whether Servo Motor can be locked
properly. While in this menu, Servo Motor is free. When the
0 0
Carriages are moved by hands, the displayed values change as
the feed-back is performed normally.
Servo Motor can be locked by pressing [ENTER] key.
When it is locked while the motor is in pause, the normal power
control is performed.
As for [F(Feed direction)], the value displayed on the left changes
0 0
by Grid Encoder, and the right changes by Motor Encoder.
START : Heater ON Default : STOP
STOP : Heater OFF
This menu is to offset heater temperature.
0 -3
The heater will be controlled with the offset temperature added to
the temperature displayed on the LCD.
Range : -5 to +5 Default : 0
0 -3
0 -3
0 -3
This menu is to specify the heater temperature of [PREHEAT] under the
[PREHEATING] menu in the USER MENU.
(The heater temperature during media not setup.)
This menu is to set the time to show the confirmation message when controlling
(in 10min. unit)
heater temperature before printing. It shows the message of [HEATING
TIMEOUT CONTINUE?] when the temperature controll is not completed at the
specified timing while controlling the heater temperature before printing.
25 C
This menu is to check the heaters and thermistors.
_ 25 C
While in this menu, it displays ON/OFF status and the temperatures read
by thermistors on each Preheater, Printheater, Dryer and Option Dryer.
[Up] and [down] keys are to select heaters or dryers, and [ENTER] key is
to turn ON/OFF the selected heater or dryer.
("ON/OFF" described here stands for power manually distributed or not.
_
25 C
It is not for controlling the temperatures set in other menus. Be aware
that the temperature keeps rising when it is left ON. It turns off automatically
when exiting the menu.)
Check if the temperature rises when the heater is ON and also if the heater
temperature decreases to ambient temperature when it is OFF.
The temperature is displayed in Celsius only.
Bit Contents
Cover Sensor 0 : Enable
Reflection to the test pattern
0 : No reflect
of a heater related parameters
Periodic flushing of MAX ink 0 : Enable
Base Head Menu 0 : Disable
Select sequence
0 : SOL ink 1 : Water-based ink
SOL/Water-based of new pump
Settings Default
0
1 : Disable (Closed status at anytime)
1 : Reflect 0
1 : Disable 0
1 : Enable 0
0