Roland SOLJET Pro III XC-540 Service Notes page 137

SERVICE MENU CUTTING MENU
CUTTING MENU CROPMARK SENSE
CUTTING MENU
FORCE ADJUST
CUTTING MENU
CROP-CUT ADJ.
CUTTING MENU
PRINT-CUT ADJ.
FRSHOCPULWcwab
SERVICE MENU
SENSOR CHECK
This menu displays the real-time status of each sensor. It shows " " when the sensor is ON.
The first page shows the status of each sensor. Each alphabet stands for as follows.
F: Front Paper Sensor
R: Rear Paper Sensor
S: Crop Mark Sensor
H: Head Lock Sensor
O: Limit Sensor
C: Front Cover Sensor
P: Maintenance Cover Sensor
CROPMARK SENSE
OUTLEVEL CHECK
CROPMARK SENSE
ADJUST
This menu is used for adjusting the Crop Mark Sensor sensitivity. There are three levels of sensitivity, 0, +1 and +2.
This adjustment may help when Crop Mark detection is failed in the default level setting. However, this setting must
not be changed unless necessary. The detection accuracy is not assured when this parameter is changed.
FORCE ADJUST
30gf
FORCE ADJUST
200gf
CROP-CUT ADJ.
TEST PRINT
CROP-CUT ADJ.
SETTING
CROP-CUT ADJ.
TEST PRINT 2
With a long press on TEST PRINT key while in this menu, it prints the test pattern of a square crop mark and cuts the contour.
With a long press on TEST CUT key, the same test print pattern as TEST PRINT 2 for position check is printed.
After test pattern is printed, it feeds media forward for visual check of the result. Press MENU key to return to the former menu.
It is available to confirm the adjustment by TEST PRINT (adjustment is reflected to TEST PRINT).
As for TEST PRINT 2, adjustment is not reflected and it always shows the original machine deviation.
The adjustment made here is not reflected to the setting of the user menu.
PRINT-CUT ADJ.
TEST PRINT
PRINT-CUT ADJ.
SETTING
PRINT-CUT ADJ.
TEST PRINT 2
With a long press on TEST PRINT key while in this menu, it prints the test pattern of a square crop mark and cuts the contour.
With a long press on TEST CUT key, the same test print pattern as TEST PRINT 2 for position check is printed.
After test pattern is printed, it feeds media forward for visual check of the result. Press MENU key to return to the former menu.
It is available to confirm the adjustment by TEST PRINT (adjustment is reflected to TEST PRINT).
As for TEST PRINT 2, adjustment is not reflected and it always shows the original machine deviation.
The adjustment made here is not reflected to the setting of the user menu.
123456789101112
H E C
U: Head Up/Down Sensor Head Up/Down Sensor
L: Sheet Load Sensor H: Head HIGH
W: Pinch Roller Sensor L: Head LOW
c: Capping Sensor
TU Motor Drive Sensor
w: Wiper Sensor
a: TU Motor Drive Sensor
Blank: Not driving
(When TU is connected)
b: Out of use
PERFORMING
TEST PRINT
This menu is used for adjusting the Crop Mark Sensor. Refer to [4-9 CROP MARK SENSOR ADJUSTMENT].
The result of this adjustment can be checked in the SENSOR CHECK menu. However, it must be aware that
without adjusting the sensor here, the result of [S: CROP MARK SENSOR] in the SENSOR CHECK menu is
not referable.
The tool carriage is free to move after OUTLEVEL CHECK is done. Moving the carriage off the crop mark
with your hand, it is available to check the level of white part, where no ink is on.
ADJUST
+2 +1
30gf
17 16
200gf
56 57
PERFORMING
TEST PRINT
F:+0.30 +0.30mm
S:-0.40 -0.40mm
Returns to menu with MENU key
PERFORMING
TEST PRINT
PERFORMING
TEST PRINT
F:+0.30 +0.30mm
S:-0.40 -0.40mm
Returns to menu with MENU key
PERFORMING
TEST PRINT
The second page shows the status of each
Cartridge Sensor and Ink Empty Sensor.
Each color has 2 positions and the left side
on the didplay shows the left-side head.
Blank: Cartridge not inserted, Ink remains
C: Cartridge inserted, Ink remains
E: Cartridge not inserted, Ink empty
: Driving
: Cartridge inserted, Ink empty
4-6
MIN 2.5V MAX2.7
[2.5V ]
This menu is used for adjusting the Tool Pressure.
Refer to [4-14 TOOL PRESSURE ADJUSTMENT].
30gf Range: 0 to 30
200gf Range: 31 to 80
This menu is used for adjusting the position of Crop
Mark Sensor and the cutting edge of Tool.
Refer to [4-10 CROP-CUT ADJUSTMENT].
When it shows [ ], it means that it has never
been setup and it needs to be set. In this case, even
if adjustment is unnessesary due to the test result,
it needs to be set with the value of [0].
This menu is used for adjusting Print/Cut position.
Refer to [4-11 PRINT/CUT POSITION ADJUSTMENT].
When it shows [ ], it means that it has never
been setup and it needs to be set. In this case, even
if adjustment is unnessesary due to the test result,
it needs to be set with the value of [0].