Setting According To Your Preferences - Panasonic Windea VGDT18143W Simple Manual

Setting According to Your Preferences

You can set ringtone volume etc. according to your preferences.
● Only the ringtones volume and touch sound can be set with the call sub-base unit with monitor.
Note
Consult with the management company or the company that installed the system for installation setting.
Setting item Setting content
Sets the ringtone and number of rings when called
Ringtone from the lobby phone (main entrance), entrance (unit
entrance (door phone)), or building manager room.
Accepting
Accepting Sets to receive the call from a base unit of other unit
call from
call or not.
other unit/
ringtone
Ringtone
Sets the ringtone and the number of rings when called.
(*1)
Sets the ringtones volume setting when called from
the main entrance, unit entrance, or building manager
room.
Ringtone
This can be set individually on the base unit and the
Note
volume
call sub-base unit with monitor.
Call sub-base unit can be adjusted with the VOLUME
button. ( Page 17)
Sets the received call time when called from the main
Received
entrance, unit entrance, other unit, or building
call time
manager room.
Sets if the touch sound for operating the touch panel
or pressing each button sounds or not.
Touch sound
This can be set individually on the base unit and call
Note
sub-base unit with monitor.
Sets the excuse tone that is played from the base unit
Excuse tone and call sub-base unit with monitor when the excuse
function is used. (Excuse function
General
Sets if general announcement from the building
announcement
manager room sounds or not.
sound
Not-home
Sets the response message when Not-home is set on.
message type
Sets the time until the response message is played
after receiving a call.
Not-home
"Not-home message timing" does not appear when it
Note
message timing
is set to "Living mode: On" with the installation setting.
Sets by changing the Not-home setting of Living
mode. ( Page 87)
Sets the response message that is played from the base
Pretend to be
unit when the Pretending to Be Out function is used.
out message type
(Pretending to Be Out function
Sets if the function to perform not-home response
Pretending to operation by displaying
be out call is received from a visitor when the Not-home
Indicator setting is set to "Off". (Pretending to Be Out function
Page 34)
90
Initial setting
Entrance (unit entrance): Melody 2
Number of rings: Ring once
Building manager room: Melody 4
Number of rings: Ring Continuously
Lobby phone: Melody 1
Number of rings: Ring Continuously
Accept calls
Melody 5
Number of rings: Ring Once
High
30 seconds
On
(immediately)
Telephone 1
Page 33)
On
Fixed Message 1
Immediately
Fixed Message 2
Page 34)
on the screen when a
Message
On
Page Setting item
Auto record notice
Yuttari On/Off
Security number
99
Security set
to
cancel sound
102
Security
alarm delay
Security
preliminary alarm
Absence Mode
Linked With
Security
103
External security
to
door phone
105
sound
ID authentication
key off
(*1)
*1: This is not displayed unless the setting on the control device or the integrated control panel is performed.
(Consult with the management company or the company that installed the system.)
Setting content
Sets if the call from the main entrance, unit entrance, or
building manager room (with video capability) has not been
answered while the Not-home setting has been set to "Off",
and a video was automatically recorded is to be noticed
with the area around the MENU button flashing in blue.
This setting is available to only the base unit with video
Note
recording function.
"Auto record notice" does not appear when set to
"Notification of new arrivals announcement: Off" by
the installation setting. (Consult with the management
company or the company that installed the system.)
Sets if the talk is always set to Yuttari Talk.
Sets the security number to cancel the security
vigilance and security alarm.
Sets the sound that is sounded when the security
circuit is set or canceled.
Sets the time until it goes into security vigilance state after
performing the arming operation of the security vigilance.
(This setting is available to each security circuit.)
●
This setting is available when set to "Permit
Note
changes to delay setting: Yes" with the installation
setting. (Consult with the management company or
the company that installed the system.
● "Security alarm delay" does not appear when set to
"Permit changes to delay setting: No".
Sets the time until the security alarm is sounded after
the installed security circuit is activated (security
preliminary alarm time). (This can be set for each
security circuit.)
●
This can be set when set to "Permit changes to
Note
delay setting: Yes" with the installation setting.
(Consult with the management company or the
company that installed the system.
●
"Security preliminary alarm" does not appear when
set to "Permit changes to delay setting: No".
Sets if the living mode is automatically set to "Absence
mode" when the external security setting is performed.
This can be set when set to "Living mode: On" and
Note
"Security system setting: External security setting" with
the installation setting. (Consult with the management
company or the company that installed the system.)
Sets the sound to be sounded from the unit entrance
when the security setting is armed or disarmed from
the external security set switch.
An installation setting is required to disarm security
Note
vigilance with the external security set switch. (Consult
with the management company or the company that
installed the system.
Sets if the security vigilance is to be disarmed together
when the main entrance (electronic lock) is unlocked
using the ID authentication device.
Continued to next page
Initial setting Page
106
On
Off 106
Off
Voice
Security 1/Security 3/
Security 4: Off
Security 2: 60 seconds
Security 1/Security 3/
Security 4: Off
Security 2: 60 seconds
107
to
110
Off
Voice
Off
91