Table of Contents
Related Manuals for Panasonic VL-GM201A
Summary of Contents for Panasonic VL-GM201A
- Page 1 Single Monitor Station Installation and Operation Guide VL-GM201A Model No. Thank you for purchasing a Panasonic Single Monitor Station. Please read this Installation and Operation Guide before using the unit and save for future reference.
-
Page 2: Table Of Contents
Table of Contents Important Information Important safety instructions ..........3 Additional safety information . -
Page 3: Important Information
The lightning flash with arrow head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. Important safety instructions 1) Read these instructions. All the safety and operating instructions should be read before the appliance is operated. 2) Keep these instructions. -
Page 4: Additional Safety Information
Important Information 12) Unplug this apparatus during lightning storms or when unused for long periods of time. This will prevent damage to the product due to lightning and power-line surges. 13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. -
Page 5: For Best Performance
21. WARNING Unplug this unit from power outlets if it emits smoke, an abnormal smell or – makes unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped and contact an authorized service center. Note: L This product has a fluorescent lamp that contains a small amount of mercury. -
Page 6: Introduction And Installation
Introduction and Installation Included items Item Monitor station Mounting bracket Wood screws Power cable AC adaptor Wood screws Power cord Quantity Notes Attached to rear of the monitor station. For the monitor station. (4 mm x 16 mm, Enclosed in the AC adaptor case. For the AC adaptor case. -
Page 7: Optional Item Information
– Desktop stand (VL-GT001A) *1 The door station figures shown in this installation and operation guide are based on a VL- GC001A. Compatible PBXs This unit is compatible with the following Panasonic PBXs – KX-TA308 – KX-TA624 – KX-TA824 – KX-TA1232 –... -
Page 8: Location Of Controls
Introduction and Installation Location of controls Front view Rear view PBX MODE Side view RINGER VOLUME HIGH ANSWER AUTO PUSH HOLD... - Page 9 A Microphone B Display C MONITOR button L Allows you to monitor the sound and camera image from the door station (page 26). D BRIGHT button L Allows you to adjust the display brightness. 5 levels are available. E DOOR button L Allows you to open the door (page 27).
-
Page 10: Before Installation
Introduction and Installation Before installation To avoid a malfunction or communication disturbance, do not install the monitor station in the following locations: – Places where vibration or any other kind of impact occurs. – Places where echoing is frequent. – Places where a high concentration of dust, hydrogen sulfide, phosphorus, ammonia, sulfur, carbon, acid, or noxious fumes occur. - Page 11 Wiring schematic diagram Door station D1 D2 (Non polar) Monitor station Note: L This door opener wiring schematic diagram is only an example. Refer to the wiring instructions provided with your door opener and PBX for details. L Refer to the technical data on page 30 when connecting to a door opener. Power cable/wire type and distance L Power cable (between the monitor station and the AC adaptor): Type: Ф1.2 Fire alarm cable 16 AWG...
-
Page 12: Installing The Monitor Station
Introduction and Installation Installing the monitor station Note: L When connecting to a PBX, make sure the {PBX MODE} switch is set to {ON} before installing the monitor station (page 20). Install the mounting bracket to a wall using the wood screws (4 mm x 16 mm, "... - Page 13 Attach the wires that connect to the door station to the terminal. See page 18 for details on how to attach the wires. L See page 11 for the wire type and distance. L See the wiring schematic diagram on page 11. Button Wire (Not included) L If you want to connect the wires and the power cable without them going through a hole...
- Page 14 Introduction and Installation Mount the monitor station to the mounting bracket. Push the monitor station down until it is secure. Take out the AC adaptor and the DC terminal from the case. L Push the arrow mark on the front case, then release from the rear case. L Take out the cardboard and wood screws.
- Page 15 Connect the power cable to the DC terminal, the power cord to the AC adaptor, then connect the power cord to the AC outlet (100 V L Be sure to connect the power cable to the 2 holes on the left side of the DC terminal. L For details on how to attach the power cable, see page 18.
- Page 16 Introduction and Installation To attach the AC adaptor and the DC terminal to a wall By placing the AC adaptor and the DC terminal in the case and mounting the case to the wall, you can protect the AC adaptor and the DC terminal from tampering and exposure. Note: L Disconnect the DC cord from the clamp on the rear of the DC terminal beforehand.
- Page 17 Introduction and Installation Attach the front of the case. Note: L To open the case again, push the bottom of the front case, then release from the rear case.
- Page 18 Introduction and Installation To attach the power cable Monitor station Button Terminal connector L While pressing on the button with a pointed object such as a screwdriver, insert the power cable into the terminal connector. L To disconnect the power cable, press on the button while pulling out. L To attach an optional power cable, cut off about 12 mm ( push in firmly until the end of the cable is securely inserted into the power connection terminal (2).
-
Page 19: Using The Desktop Stand (Optional)
Using the desktop stand (Optional) You can place the monitor station on a desktop. See page 7 for optional item information. Wire Power cable Note: L If you previously connected the power cable through the power cable guide (page 13), remove the power cable from the power cable guide of the monitor station beforehand, then attach to the desktop stand. -
Page 20: Using The Unit
Using the Unit Turning {PBX MODE} switch ON/OFF When connecting to a PBX (page 22), turn {PBX MODE} switch on. If not, turn {PBX MODE} switch off. The default setting is {ON}. Remove the switch cover from the rear of the monitor station. L Use a sharp, thin object such as a mechanical pencil. - Page 21 Using the Unit Attach the switch cover to the rear of the monitor station. Switch cover...
-
Page 22: Connecting To A Pbx
Connecting to a PBX allows you to answer door calls from any telephone. See page 11 for wiring information. Please use only a Panasonic PBX. See page 7 for the PBX model list that is compatible and other optional hardware. -
Page 23: Answering A Door Call Using The Monitor Station
Answering a door call using the monitor station There are 3 ways to answer a door call using the monitor station. Choose the desired mode by changing the {ANSWER} switch position. Important: L When speaking with a caller, speak in turns. If you and the caller speak at the same time, you will not hear each other. - Page 24 Using the Unit {PUSH} mode (Push to talk mode) When a call is received from the door station, press {TALK}. Speak to the visitor. To end the conversation, press {TALK}. L The display will turn off. {AUTO} mode (Auto talk mode) This mode allows you to answer the call by voice.
- Page 25 Note: L Speak clearly about 50 cm (20 inches) away from the microphone. L While the display is on, you can press {BRIGHT} repeatedly to select the desired brightness. If a power failure occurs, the brightness setting will be reset. L If you do not answer a door call within 30 seconds, the display will turn off.
-
Page 26: Monitoring The Outside
Using the Unit Monitoring the outside You can monitor the sound and camera image from the door station for up to 1 minute at a time. Press {MONITOR}. L The outside image will be shown on the display, and the outside sound will be heard. The inside sound will not be heard at the door station. -
Page 27: Opening A Door (Door Opener)
Opening a door (door opener) You can open the door using the monitor station (a separate door opener is required). While the display is on, press and hold {DOOR}. L The door will remain open while {DOOR} is pressed. Note: L See page 11 for wiring information. -
Page 28: Help
Help Troubleshooting Problem The display is not clear or is blurry. The display is white, or black or white lines are shown on the display. The color of the display is different from the actual color. The display will not display anything or no voices can be heard. -
Page 29: Cleaning
Problem The display turns off during a conversation (Sound continues). Cleaning Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit with a slightly damp cloth. Important information: L Do not use anything containing alcohol, polish powder, powder soap, benzine, thinner, wax, petroleum, or boiling water. -
Page 30: General Information
General Information Technical data about this product Monitor station Power supply: Current consumption: Dimensions: Mass (Weight): Operating environment: Installation method: External material: Note: L To connect to a door opener, make sure the door opener is: – Normal open (Low active) –... -
Page 31: Fcc And Other Information
General Information FCC and Other Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. - Page 32 San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico 00985, U.S.A. Copyright: L This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd.