Table of Contents
Advertisement
In the Event of Water Leaks
When the water leak sensor detects a water leak, the system reports a water leak.
Note
Confirm that system components are properly installed before using the system.
●
The alarm stops approximately 30 seconds
after the water leak sensor activates. Note
that the indicators on the base unit, sub-base
unit, and door phone continue to flash.
●
Approximately 1 minute after the water leak
sensor activates, the water leak icon turns
off, and the area around the MENU button
will flash in red.
●
Once the water leak is no longer detected,
the area around the MENU button, call
sub-base unit ALARM indicator, and door
phone alarm display indicator turn off.
●
After pressing the STOP ALARM button,
touching
on the base unit will cause
the screen to return to the waiting state, and
the area around the MENU button will light
up in red. To display the water leak icon,
touch
on the Top Menu screen.
(
Pages 20 to 21)
●
The area around the MENU button, ALARM
Note
indicator, and alarm display indicator
continue to flash until the water leak sensor
no longer detects a water leak.
●The water leak icon can also be turned off
within 1 minute. (
Page 155)
How to stop the alarm sound
●
Press the STOP ALARM button.
Reports to the building manager room are
sent after approximately 30 seconds. The
alarm that triggers in the unit can be
turned off from the building manager
room.
Procedures during alarms
●
Confirm the alarm details and then perform the
appropriate procedures.
●
The alarm message played
Installer
during water leak alarms can be
Setting
continued or disabled.
●
Reports made to the building
manager room can be sent
immediately.
Consult with the management
company or the company that
installed the system.
172
(Beeps)
Water leak.
STOP ALARM
button
復旧/警報音停止
RESET/ STOP ALARM
The water leak icon
flashes in red.
MENU button
Confirm button
電源
Call sub-base unit
Door phone
POWER
ALARM indicator
Alarm display indicator
Flashes in red
Flashes in red
Alarm is sounding
● For base unit
and
do not appear in
Note
the call sub-base unit with monitor.
Wireless Equipment Failures
When the wireless equipment experiences a failure, the system reports a wireless equipment failure.
Note
Confirm that system components are properly installed before using the system.
●
The wireless equipment failure icon will turn off after
approximately 1 minute, and the area around the
MENU button will flash in red.
●
The area around the MENU button turns off when
the wireless equipment failure clears.
●
Touching
on the base unit will cause the
screen to return to the waiting state, and the area
around the MENU button will light up in red. To
display the wireless equipment failure icon, touch
on the Top Menu screen. (
Pages 20 to 21)
Note
The wireless equipment failure icon can also be
turned off within 1 minute. (
Page 155)
Fault resolution procedures
●
Refer to the operation manual provided with the
wireless contact output receiver and perform
the necessary procedures.
An alarm can be triggered when the wireless equipment experiences a failure.
Installer
Setting
(Consult with the management company or the company that installed the system.)
Dead Wireless Equipment Batteries
When the battery in the wireless equipment dies, the system reports that the wireless battery is dead.
●
The dead wireless equipment battery icon will turn
off after approximately 1 minute, and the area
around the MENU button will flash in red.
●
The area around the MENU button turns off when
the dead wireless equipment battery clears.
●
Touching
on the base unit will cause the
screen to return to the waiting state, and the area
around the MENU button will light up in red. To display
the dead wireless equipment battery icon, touch
on the Top Menu screen. ( Pages 20 to 21)
Note
The dead wireless equipment battery icon can also
be turned off within 1 minute. (
Page 155)
Fault resolution procedures
●
Refer to the operation manual provided with the
wireless contact output receiver and perform
the necessary procedures.
An alarm can be triggered when the wireless equipment battery dies.
Installer
Setting
(Consult with the management company or the company that installed the system.)
■ Wireless contact output receiver status
When the battery in the wireless contact
point transceiver is nearly dead:
●
The battery replacement indicator appears
in red. (
Page 155)
●
The contact output operation indicator to which
a wireless transceiver is registered appears in
red as normal when the battery in that wireless
transceiver dies. ( Page 155)
STOP ALARM
button
Wireless
復旧/警報音停止
equipment
RESET/ STOP ALARM
failure icon
appears in red
MENU button
Confirm button
電源
POWER
● For base unit
and
do not appear in
Note
the call sub-base unit with monitor.
STOP ALARM
button
Dead wireless
復旧/警報音停止
RESET/ STOP ALARM
equipment
battery icon
appears in red
MENU button
Confirm button
電源
POWER
● For base unit
and
do not appear in call
Note
sub-base units with monitor.
If a system failure occurs:
●
The operation indicator flashes. ( Page 155)
The operation indicator flashes when power is
Note
restored after a blackout. However, the "Wireless
equipment failure" message does not appear.
Refer to the operation manual provided with the
wireless contact output receiver for more information.
173
Advertisement
Table of Contents
