Making Calls; Making Emergency Call Alarms - Panasonic Windea VGDT18143W Simple Manual

Making Calls

Note
Confirm that system components are properly installed before using the system.
When the Call Button is Pressed
When the Call button is pressed, the system reports the call.
● The Call 1 icon will turn off after approximately
1 minute, and the area around the MENU
button will flash in red.
● If the Call button is reset, the call alarm stops,
and the area around the MENU button turns off.
Note
●
If a reset is performed within 20 seconds of the
button being pressed, the Call 1 icon flashes for
approximately 20 seconds after the button is
pressed, and then turns off.
● The Call 1 icon can also be turned off within
1 minute. ( Page 155)
●
Up to 4 Call buttons can be connected. The
screen display appears in accordance with the
configured installation settings.
How to stop the call sound
● Press the STOP ALARM button.
Call procedures
● Confirm the call details and then perform
the appropriate procedures.
● The screen displayed during calls
Installer
can also be changed.
Setting
● The location of the caller can also
be announced.
● Calls can continue after the
pressed button is released.
(self-retention)
● The volume of the base unit
ringtone can be changed.
Consult with the management
company or the company that
installed the system.
164
Call button
Press
(Beeps)
STOP ALARM
button
復旧/警報音停止
RESET/ STOP ALARM
Call 1 icon
flashes in yellow
MENU button
電源
POWER
Call sub-base unit
Call is ringing
● For base unit
Note does not appear in the call
sub-base unit with monitor.

Making Emergency Call Alarms

Note
Confirm that system components are properly installed before using the system.
Configure the emergency call alarm as the call function.
Installer
Setting
The emergency call alarm can also be configured as the toilet or bathroom
announcement. (Consult with the management company or the company that installed
the system.)
When the Call Button is Pressed
When the Call button is pressed, the system
reports the call.
● The Call 1 icon will turn off after approximately
3 minutes, and the area around the MENU
button will flash in red.
● If the Call button is reset, the alarm stops. Also,
the area around the MENU button, ALARM
indicator on the call sub-base unit, and door
phone alarm display indicator turn off.
●
If a reset is performed within 20 seconds of the
Note
button being pressed, the Call 1 icon flashes for
approximately 20 seconds after the button is
pressed, and then turns off.
● The Call 1 icon can also be turned off within
3 minute. ( Page 155)
● Up to 4 call buttons can be connected. The
screen display appears in accordance with the
configured installation settings.
How to stop the alarm sound
● Press the STOP ALARM button.
(The alarm can also be turned off from
the building manager room.)
Procedures during alarms
● Confirm the alarm details and then perform
the appropriate procedures.
● The screen displayed during
Installer
emergency calls can also be
Setting
changed.
● The location of the caller can also be
announced.
● Alarms can continue after the pressed
button is released. (self-retention)
● Reports made to the building
manager room and door phone can
be delayed.
●
Playback of the alarm from the door
phones can be disabled.
●
Reports made to the building
manager room can also be disabled.
Consult with the management
company or the company that
installed the system.
Call button
Press
(Siren) Please come
immediately.
STOP ALARM
button
復旧/警報音停止
RESET/ STOP ALARM
Call 1 icon
flashes in red
MENU button
電源
POWER
Call sub-base unit
ALARM indicator
Flashes in red
Alarm is sounding
● For base unit
Door phone
Alarm display indicator
Flashes in red
Alarm is sounding
Note does not appear in the call
sub-base unit with monitor.
165