Table of Contents
Advertisement
Arming Individual Security System
(For base unit)
When the "Individual Security System" setting is enabled, the individual window and door circuits of
the security system can be armed separately.
●
Note
This feature is only available when the "Individual Security System" is enabled (installation settings).
Consult with the management company or the company that installed the system.
●
The screen is displayed the security alarm delay screen and setting the Not-home setting is not
available. Set the Not-home setting ( page37) before setting the security alarm.
●
When the call sub-base unit is connected, the base unit cannot be operated at the same time that
the sub-base unit is operated.
1
Close and lock all windows and doors
equipped with magnet switches
●
The security system cannot be enabled if the
Note
windows and doors are not properly closed and
locked.
●
Due to the effect of the magnets, the security
system may arm even if the windows and doors are
not completely closed. Close and lock the windows
and doors before arming the security system.
2
Press the MENU button in the
waiting state (nothing is
displayed on the screen)
●
The Top Menu screen appears.
3
Touch
●
The Security Setting screen
appears.
●
Touch
if using Living
mode.
4
Touch
for the security system
circuit you wish to arm
●
The security system arms immediately for
windows and after approximately 60 seconds
for the front entrance door. Once armed, the
"Security has been turned on." message
appears.
●
The Security SET indicator appears in green.
Touch to arm the security system for
●
both windows and doors. (Window circuits
arm immediately, and the door circuit arms
after approximately 60 seconds.)
does not appear if only the Security 1 circuit
Note
is configured.
192
復旧/警報音停止
RESET/ STOP ALARM
MENU button
電源
POWER
Press
<When using Living mode>
Touch
Touch
Touch
any one
●
The configured security system circuit
appears. (Up to 4 security circuits
can be configured.)
Open: A window or door connected to
the system is open.
Close: All windows and doors connected
to the system are closed.
Continued on the next page
●
The security system delay start message plays
while the user arms the security system. A
sound will be played 30 seconds before the
security system is armed. 15 seconds before
the security system arms, an audible
countdown is triggered every approximately
5 seconds until the security system arms. Once
armed, the audible "Security has been turned
on." message is triggered. (Default value)
●
The security system arms immediately for
both the windows and front entrance door
when all security system circuits are set to
"Security alarm delay setting: Off"
(
page 108).
Touch
to arm the security system
immediately.
●
Touch
to disarm the security system.
●
Arming the security system while windows and doors
Note
installed with magnet switches are open causes the
audible security lock-up message (
page 227) to be
triggered, the "Check that all windows and doors are
locked." message appears, and the Security SET indicator
flashes in green. Close and lock the windows and front
entrance door to arm the security system. Touch
if you desire to disarm the security system.
●
The same message that plays from the base unit
also plays from the sub-base unit and extension
speakers if connected.
●
The system can be configured not to play the
message when the security system is armed. A
confirmation sound "beep" can also be enabled.
(
See page 108 for information on the Security Off
Sound). (The sound used when disarming the
security system is also changed.)
The security system can be armed without
Installer
Setting
the countdown when the security system
delay is nearly over.
Consult with the management
company or the company that
installed the system.
5
When leaving your home, exit from
the condominium unit entrance and
lock the front entrance door
●
Exit from the condominium unit entrance
within the security system delay time.
(
Page 197)
●
Press the OFF button when not going out.
(The security system will arm after the
security alarm delay time elapses.)
●
The security system delay time can be
shortened by operating the door phone.
(
page 194)
After approx. 5 seconds
復旧/警報音停止
RESET/ STOP ALARM
電源
警戒
SET
POWER
Security SET indicator appears in green
(flashes during the delay time)
After approx. 5 seconds
●
The individual Security Setting
screen appears.
193
Advertisement
Table of Contents
