Activating The Emergency Alarm - Panasonic Windea VGDT18143W Simple Manual

Disarming Security Alarms (disable any active security and security preliminary alarms) (for Base Unit)
1
Touch on the base unit
while the preliminary security alarm
or security alarm is active
● The "Enter the security number." screen
appears.
● Security alarms are disarmed if no
security number has been configured.
Step 2 and subsequent steps do not
need to be performed.
2
Enter the security number
●
The entered security number appears.
●
Note The security alarm and security preliminary alarm
remain active if no operation is performed for 10
seconds. If this happens, repeat the procedure
1
from Step .
● Touch if in the security number is entered
incorrectly. All numbers will be cleared.
3
Touch
● If the entered security number is correct, the
Security SET indicator turns off, and the
security alarm is disarmed.
After the security disarmed message is
triggered, and the "Security has been turned
off." message appears on the screen, the
Top Menu screen appears. (The Mode
Change screen appears instead if using
Living mode. Select Living mode.)
●
If the entered security number is incorrect,
the system returns to the "Enter the security
number." screen. If this happens, repeat the
procedure from Step .
2
● All security system alarms are disarmed when this
Note
procedure is performed.
(This is also applicable when the "Security
Individual Alarm" is enabled.)
●
The security disarmed message can be
disabled or changed to a simple
sound alarm.
Security Off Sound
settings ( Page 108)
170
Security Alarm Activations
電源
警戒
FIRE FIRE GAS GAS Not Home NOT HOME SET OPEN OPEN
POWER
Security SET
indicator flashes
Touch
in green
Touch
the numeric
buttons
Touch
● The figure illustrates an example of entering "1234".
Touch
any one
● When using Living mode

Activating the Emergency Alarm

Note
Confirm that system components are properly installed before using the system.
If the EMERGENCY Button or Other Emergency Button is Pressed
If the EMERGENCY button or other Emergency button is pressed, the system
reports the state of emergency.
(Siren)
Emergency.
EMERGENCY button
flashes in red
復旧/警報音停止
RESET/ STOP ALARM
STOP ALARM button
Emergency icon
flashes in red
MENU button
電源
Call sub-base unit Door phone
POWER
ALARM indicator Alarm display indicator
Flashes in red Flashes in red
Alarm is sounding Alarm is sounding
● For base unit
Note does not appear in the call sub-base
unit with monitor.
● The Emergency icon will turn off after
approximately 3 minutes, and the area around
the MENU button will flash in red.
●
If the pressed EMERGENCY button is reset,
the alarm stops. Also, the area around the
MENU button, ALARM indicator on the call
sub-base unit, and door phone alarm display
indicator turn off.
● The EMERGENCY button, area around the
Note
MENU button, and alarm display indicator
continues to flash until the pressed
EMERGENCY button is reset.
●
The emergency icon can also be turned off
within 3 minutes. ( Page 155)
● If some other Emergency button is pressed,
the EMERGENCY buttons on the base unit
and sub-base unit do not flash.
How to stop the alarm sound
● Press the STOP ALARM button.
The alarm can be also be turned off
from the building manager room.
Procedures during alarms
● Confirm the alarm
details and then
perform the appropriate
非常
EMERG.
procedures such
as notifying
復旧/警報音停止
neighbors.
復旧/警報音停止
RESET/ STOP ALARM
電源
POWER
非常
EMERG.
How to reset the EMERGENCY button
on the base unit and call sub-base unit
Press the EMERGENCY button again
The EMERGENCY button turns off.
How reset other Emergency buttons
Press the button or pull the drawstring
again.
Model WTF4510W
Open the Emergency button and reset
the protection board.
1 Remove the cover.
2 Pull the button forward.
1
Cover
2
Button
3 Reposition the protection board back
to its original position and place it
inside the main unit.
Back of the cover
3
Press to
reset.
Protection board
● The alarm sound can be disabled.
Installer
setting The alarm display for the Emergency
icon etc. will still appear on the
display, or the report will be sent.
● Reports made to the building
manager room and door phone can
be delayed by approximately
30 seconds.
Consult with the management
company or the company that
installed the system.
171