Unlocking The Unit Entrance; Useful Functions (Continuation Function); Configure The Not-Home Setting - Panasonic Windea VGDT18143W Simple Manual

Unlocking the Unit Entrance

Note
You can lock and unlock the unit entrance if the electronic lock system installed in your unit is connected to
the condominium HA system.
Press the UNLOCK button flashing in green
while talking with the unit entrance
●
The unit entrance is unlocked, the UNLOCK
button turns off for approximately 2 seconds,
and then it starts to flash in green again.
● The call automatically ends approximately
5 seconds after pressing the UNLOCK button,
and then the UNLOCK button and the
TALK button turn off.
Note
● The call is not automatically terminated
while the unit entrance is unlocked even
if the UNLOCK button is pressed.
Useful Functions
Continuation Function
!
Convenient
You can extend the call time when you are talking with the main entrance, unit entrance, building
manager room (with video capability), or other unit and want to extend the time to 1 minute or more.
Use the Continuation function to extend the call up to 3 minutes.
(Normally, the call ends automatically after approximately 1 minute.)
Press the TALK button when the
"beep, beep" sound plays and the
TALK button flashes
● The TALK button starts flashing approximately
50 seconds after the call starts. You can talk
for an additional minute after the initial minute
finishes.
The TALK button starts flashing again
after approximately 1 minute and
50 seconds you start the call.
●
The call can be extended up to two times.
The maximum calling time including extended
time is approximately 3 minutes.
When talking with the building manager room (without video capability)
● A "beep, beep" sound plays approximately 3 minutes and 50 seconds after the call starts and the TALK
button starts flashing. Press the TALK button during the call to continue. You can talk for an additional 3
minutes after the initial 4 minutes are finished. (The TALK button starts flashing again approximately 6
minutes and 50 seconds after you start the call.)
● The call can be extended up to two times. The maximum talking time including extended time is
approximately 10 minutes.
36
Receiving a Call
(For call sub-base unit)
(illuminated UNLOCK button)
Lights up in red when unlocked
Turns off when locked
UNLOCK
button
VGD13113W VGD13113W
非常
EMERG.
ロビー ロビー
警報 警報 管理 管理
ALARM ALARM MANAGER MANAGER LOBBY LOBBY
Flashes in green
室内呼 解錠
UNLOCK
EXTENSION
呼出音量 (When it can be locked
VOLUME
通話
TALK
or unlocked)
Press Press
Turns off in approx.
2 seconds and then
flashes in green again
VGD13113W VGD13113W
非常
EMERG.
警報 警報 管理 管理 ロビー ロビー
MANAGER MANAGER
ALARM ALARM LOBBY LOBBY
解錠
室内呼
UNLOCK
EXTENSION
呼出音量
VOLUME
通話
TALK
TALK button

Configure the Not-home Setting

(For base unit)
Use this function when you are out or away from home. If the Not-home function is set and the
base unit receives a call, the call sound rings, then the Not-home message (
and the visitor's voice is automatically recorded. (
recorded when using a base unit with sound and video recording function.)
Configure the Not-home setting with the Living mode when using the "Absence/Sleeping/
Note
Home" switching function with that mode. (
Configure the Not-home Setting
1
Press the MENU button in the
waiting state (nothing is
displayed on the screen)
● The Top Menu screen appears.
2
Touch
3
Not-home setting is
configured
● switches to .
● The NOT HOME indicator lights up
in red.
NOT HOME
indicator
lights up in red
4
Press the OFF button to exit
●
It will return to the waiting state (nothing
is displayed on the screen).
Note The screen will automatically turn off
when no operation is performed for
30 seconds.
page 103) plays,
page 27) (A video of the visitor is also
Page 85)
復旧/警報音停止
RESET/ STOP ALARM
MENU button
電源
火災 ガス 留守 警戒 戸締り OPEN Press
FIR E GAS NOTHOME S ET
POWER
Touch
復旧/警報音停止
RESET/ STOP ALARM
電源
火災 FIR E ガス GAS 留守 NOTHOME 警戒 S ET 戸締り OPEN
POWER
終了
OFF
Press
37