Panasonic Windea VGDT18143W Simple Manual page 57

Set the security number in the following
procedure when
is touched
1
Enter the 4 digit security number
Note Touch when wrong number is entered.
All the numbers are erased.
2
Touch
●
Security number is set.
●
Returns to the Security Setting screen.
Security Off Sound
To set the sound played in the door phone, set in "External Security Door Phone Sound".
Note
( Page 109)
3
Select one of "Voice/Imitation Sound/
Off", and touch
Sound message is played.
When security is turned on: Security has
been turned on.
Voice
When door closure security is on: Beep,
(Initial setting)
Check that all windows and doors are locked.
When security is turned off: Security has
been turned off.
Notification sound is sounded.
Imitation
When security is turned on: Beep
When door closure security is on: Beeps
Sound
When security is turned off: Short beeps
Off No message or notification sound is sounded.
Security Alarm Delay
●
This setting is available when set to "Permit changes to delay setting: Yes" with the installation setting.
Note
(Consult with the management company or the company that installed the system.)
●
"Security Alarm Delay" does not appear when set to "Permit changes to delay setting: No".
3
Touch of the security circuit to
change, select one of "Off/30sec./60sec./
120sec./300sec.", and touch
It will go into security vigilance state immediately
Off
after setting the security.
It will go into security vigilance state approximately
30sec.
30 seconds after setting the security.
It will go into security vigilance state approximately
60sec.
60 seconds after setting the security.
It will go into security vigilance state approximately
120sec.
120 seconds after setting the security.
300sec. It will go into security vigilance state approximately
300 seconds after setting the security.
Security 1/Security 3/Security 4: Off
Initial setting
Security 2: 60 sec.
108
2
1
Touch the
numeric buttons
● When entered as 1234
Security Off Sound screen
1 2
Touch Touch
any one
Security Alarm Delay screen
Touch
any one
2
1
Touch
any one
Security Preliminary Alarm
●
This setting is available when set to "Permit changes to delay setting: Yes" with the installation setting.
Note
(Consult with the management company or the company that installed the system.)
●
"Security Preliminary Alarm" does not appear when set to "Permit changes to delay setting: No".
3
Touch
select one of "Off/30sec./60sec./120sec./
Touch
300sec.", and touch
Off
30sec.
60sec.
120sec.
300sec.
Initial setting
Absence Mode By Security
This setting is available when set to "Living mode: On" and "Circuit setting: External security" with the installation setting.
Note
(Consult with the management company or the company that installed the system.)
3
Select either of "On/Off", and touch
On
Off
(Initial setting)
External Security Door Phone Sound
An installation setting is required to disarm security vigilance with the external security set switch.
Note
(Consult with the management company or the company that installed the system.)
3
Select one of "Voice/Imitation Sound/
Off", and touch
Voice
(Initial setting)
Imitation
Sound
Touch
Off
Setting According to Your Preferences
Security Preliminary Alarm screen
of the security circuit to change,
Security alarm is immediately sounded when the door
is opened while security alarm is set.
Security preliminary alarm is sounded for approximately
30 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
Security preliminary alarm is sounded for approximately
60 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
Security preliminary alarm is sounded for approximately
120 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
Security preliminary alarm is sounded for approximately
300 seconds when the door is opened when security
vigilance is set, then security alarm is sounded.
1
Security 1/Security 3/Security 4: Off Touch
Security 2: 60 sec.
any one
Absence Mode By Security screen
Sets the living mode automatically to "Absence mode"
when the external security setting is performed.
Changing the setting of the security setting
Note
for the Absence mode is not available.
The Living mode is not changed even
when the external security is set.
Sound message is played from the unit entrance (door phone).
When security is turned on: Security has been turned on.
When door closure security is on: Beep, Check that all windows
and doors are locked.
When security is turned off: Security has been turned off.
Notification sound is sounded from the unit entrance (door phone).
When security is turned on: Beep
When door closure security is on: Beeps
When security is turned off: Short beeps
No message or notification sound is sounded
from the unit entrance (door phone).
Touch
any one
2
Touch
2
Touch
1
Touch
any one
Door Phone Sound screen
2
Touch
1
Touch
109
any one