Roland VersaUV LEJ-640 Service Notes page 216

SUB MENU
CLOCK
SUB MENU
DIP SW CHECK
SUB MENU
KEY CHECK
SUB MENU
LCD/LED/BUZ CHK
SUB MENU
PORT CHECK
SUB MENU
MAINTE. MSG.
SUB MENU
PAPERSIDE SENSE
SUB MENU
MEDIA CLAMP CHK
SERVICE MENU MOTOR MENU
MOTOR MENU AGING
CLOCK
DATE
CLOCK
TIME
This menu is to display and edit the date and time. When it detects the battery exhaustion, [B] is indicated on the time display. In this case,
battery needs to be replaced. However, [B] does not disappear automatically when the battery is replaced. [B] is deleted, when the time is
newly set up with [ENTER] key on the time edit menu.
When the real time clock is not active due to battery exhaustion, the maintenance operation may be performed improperly, such that it
performs cleaning every time the main power is turned on. The time set here is used for periodic maintenance operations and the time record
of Event Log function. Be aware that it affects the maintenance operations if the time is changed.
When this setting is changed, it is recorded on Event Log. The time before change is used for the log time, and the new time is recorded as an information.
DIP SW CHECK
0110 0000
bit # [1 2 3 4 5 6 7 8]
KEY CHECK
NONE
Abbreviated
Returns when completed
Waiting for incoming data
DETECTING...
00: 0B
Receiving data from network
NETWORK
B3:1073741624B
MAINTE. MSG.
NONE 100 hours
PAPERSIDE SENS
OUTPUT LEVEL
PAPERSIDE SENS
SENSOR AUTOTEST
NOW PROCESSING...
AGING
SCAN
AGING
FEED
AGING
BOTH
4-8
DATE
DATE
05/09/10 05/09/10
[Year/Month/Day]
[Year/Month/Day]
Display
TIME
TIME
01:01:59 01:01:59
Display
TIME
TIME
01:01:59 B
01:01:59
This menu is to check Dip Switch. It displays the real-time status of the No.1 to 8 from the left.
[0] is OFF and [1] is ON.
This menu is to check the operation of panel keys. On this menu, it shows [NONE] on the lower
LCD when any key has not been pressed. It shows the key name when some key is pressed. And
it shows a message of [KEY ERROR] when two keys or more are pressed at the same time, and it
is considered that no button is pressed. You can exit this menu with the [left] key. Therefore, the
[left] key needs to be the last button to be pressed in order to check all keys. As long as the [left]
key is pressed at the last, the order of pressing other keys can be random. When it is left without
pressing any key for 10 seconds, or pressing the [left] key, it exits this menu. At this time, the
names of the keys that never been pressed are displayed with a buzzer. This means that if a
buzzer does not go off when exiting, all keys are checked properly. The power cannot be turned
off with the sub power key while performing this menu.
This menu is to check LCD, LED and buzzer. When this menu is selected, it sequentially performs
the functions of LCD, LED and buzzer. The functions are the followings, LCD back light,
ON/OFF of buzzer, and display of all LCD dots available on LCD.
Confirm that all functions operate properly, visually and by the sound.
This menu is to confirm the data input from network. The check sum and input data byte are
shown on the lower LCD. On the left, it displays the check sum in hexadecimal of 2 digits. On the
right, it displays the input data byte in decimal of max. 10 digits. They are cleared when [ENTER]
key is pressed. The input data byte overflows at 4GB(4294967296B) and resets to 0.
* When transffering from VersaWorks, send the data from [Send Native File].
This menu is to set up the timing to show the message for maintenance. It displays the message
suggesting to perform maintenance when the total print time reaches the specified hours.
Range: NONE, 10 to 999 hours (in 10 hour unit)
OUTPUT LEVEL
0.73V
SENSOR AUTOTEST
NOW PROCESSING...
When 2 MEDIA CLAMP is detected. (beep one time)
MEDIA CLAMP CHK
COMPLETED
When 1 MEDIA CLAMP is detected. (beep one time)
MEDIA CLAMP CHK
FOUND 1 CLAMP
When MEDIA CLAMP is not detected. (beep two times)
MEDIA CLAMP CHK
FAILED
SCAN
SCAN : Aging for Scan Motor. The Head Carriage runs maximum
printing width in Scan direction.
NOW AGING
FEED : Aging for Feed Motor.
Grit Roller runs 100mm back and forth.
BOTH : The Head Carriage runs maximum printing width in
FEED
Scan direction, and at the same time, Grit Roller runs
NOW AGING
100mm back and forth.
To stop Aging, press the [ENTER] key. The Head Carriage returns
BOTH back to the capping position, and it returns to the former menu
after the heads are capped. Make sure not to perform Aging for
NOW AGING
excessive time when the heads are filled with ink, in order to
prevent the heads from being damaged by dried ink.
When Aging is performed with ink filled, it runs with performing
the Flushing. No Flushing when ink is not filled.
Edit
Edit
It shows [B], when
battery is dead.
B
Default: NONE
0.5V, NOISE 1
This menu is for checking the detection of
the Media Clamp.