Roland VersaUV LEJ-640 Service Notes page 213

I/S MENU NOW PROCESSING..
CAP AGING
NOW PROCESSING..
I/S MENU
WIPER AGING
I/S MENU NOW PROCESSING..
CAP AGING
NOW PROCESSING..
I/S MENU
WIPER AGING
Remove all cartridges
before pressing ENTER
CARTRIDGE
I/S MENU
IC CHECK
CARTRIDGE
CARTRIDGE
SLOT 1
CAP AGING
COMPLETED
Error (beeps 2 times)
CAP AGING
FAILED !!
WIPER AGING
COMPLETED
Error (beeps 2 times)
WIPER AGING
FAILED !!
CAP AGING
COMPLETED
Error (beeps 2 times)
CAP AGING
FAILED !!
WIPER AGING
COMPLETED
Error (beeps 2 times)
WIPER AGING
FAILED !!
Set cartridge to SLOT1 All cartridges must be removed before entering IC
CHECK menu.
IC CHECK
It detects Ink Cartridge IC, writes and loads
SLOT1 INSERT
information, and checks the communication. First of all,
it confirms if there is the driver for IC detection. The
following display indicates that error is found on driver.
Error
IC CHECK
SLOT1 ERROR
Next, IC communication is checked individually by
Normal
SLOT. When a cartridge is inserted, it automatically
IC CHECK
starts to communicate with the cartridge IC and checks
it. Display shows [OK], when the communication is
SLOT1 OK
done properly.
As cartridge is removed, the next cartridge SLOT
From SLOT1 to 6 in order
number to be inserted is displayed. Starting from
SLOT1, it continues to SLOT6 in order. When checking
Set cartridge to SLOT6
SLOT6 is completed, the following message is
IC CHECK
displayed.
SLOT6 INSERT
It returns to IC CHECK menu by pressing ENTER key.
Error
When communication is failed, it displays as below.
IC CHECK
SLOT6 ERROR
Normal
IC CHECK It returns to IC CHECK menu by pressing ENTER key.
SLOT6 OK
*Any cartridge can be used for this check as long as it
has IC chip on it.
*No information is written on IC chip during this check.
IC CHECK (Normally, the count of the cartridge installation is
written. However, the count of the installation in this
COMPLETED
check is not written.)
*Before this IC check, make sure Cartridge Sensor is
working properly.
SL1 : SERIAL
Serial No. of the Ink Cartridge IC is displayed.
1402A30C010000A5
SL1 : INK TYPE
Ink type of the Ink Cartridge IC is displayed.
eUV K
SL1 : CAPACITY
Ink capacity of the Ink Cartridge IC is displayed.
200cc
SL1 : LOT NO.
Lot No. of the Ink Cartridge IC is displayed.
40216A
SL1 : CONSUM.
Ink consumption of the Ink Cartridge is displayed.
100.000cc
4-5
This is to confirm that the capping is
done properly within the operation range.
The cap move up and down 20 times in
this menu.
The wiper move back and forth 20 times
in this menu.
After this menu is performed, the Cap remain
opened. Perform [I/S CONTROL] >
[HEAD UP/DOWN] > [MIDDLE] to move down the
Head Carriage, then perform [I/S CONTROL] >
[CAP] > [CLOSE] to cap the Print Head.
The Wiper Unit move up and down 20 times
in this menu.
After this menu is performed, the Cap remain
opened. Perform [I/S CONTROL] >
[HEAD UP/DOWN] > [MIDDLE] to move down the
Head Carriage, then perform [I/S CONTROL] >
[CAP] > [CLOSE] to cap the Print Head.
The Head Carriage move up and down 20
times in this menu.
IC CHECK
SYSTEM ERROR
IC CHECK
COMPLETED
IC CHECK
SLOT1 ERROR