Roland VersaUV LEJ-640 Service Notes page 210

4-1 SERVICE MODE
+ POWER ON
SERVICE MENU PRINT MENU
PRINT MENU HEAD RANK
PRINT MENU
HEAD ADJUST
MENU
[ MENU ] key
SERVICE MENU
HEAD RANK
HEAD 1
HEAD RANK
HEAD 6
HEAD ADJUST
BIAS/VERTICAL
HEAD ADJUST
HORIZONTAL
HEAD ADJUST
BI-DIR.DEFAULT
HEAD ADJUST
STANDARD HEAD
This menu is used for adjusting Head Alignment. Refer to [4-4 HEAD ALIGNMENT].
HEAD RANK 1
This menu is used for entering the HEAD RANK for each HEAD with
35 digit number and alphabet. The digits can be changed with [left]
1234567 (1/5)
and [right] keys and parameters can be changed with [up] and [down]
keys. The digit being changed is marked with an under bar. Press the
[ENTER] key to save the settings.
HEAD RANK 6
Warning sound goes off when the calculation for verification, CHECK
1234567 (1/5)
SUM, is not correct, in order to avoid input error.
BIAS/VERTICAL PERFORMING
TEST PRINT
Set Head Height to LOW or MIDDLE.
Head height is set to MIDDLE automatically for printing.
Feeds media for visual check of the test pattern, by pressing [up] or [down] keys
while in [TEST PRINT] menu. Also by pressing [up] or [down] keys again after
feeding, media returns to the original position.
BIAS/VERTICAL
--- VIEW ---
HORIZONTAL
PERFORMING
TEST PRINT
Set Head Height to LOW.
Head height is set to LOW, MIDDLE and HIGH automatically for printing.
H1
HORIZONTAL
DT1, Low 2
HORIZONTAL
H1
DT3, Low 2
HORIZONTAL H1
DT1, Middle 2
HORIZONTAL
H1
DT3, Middle 2
HORIZONTAL H1
DT1, High 2
HORIZONTAL
H1
2
DT3, High
Cursor can be moved with [left] and [right] keys, and value can be selected with [up] and [down] keys.
The value being selected is marked with an under bar. It returns to the former menu by pressing [left]
key when the cursor is on the head of the left end. H4 is defined as the standard head in this case.
Default: 0 Range: -30 to +30dot (changeable by 0.5dot) 0.5dot is indicated as 1/2.
BI-DIR.DEFAULT
TEST PRINT
TEST PRINT
123456
Set the head height to LOW.
Head height is set to LOW, MIDDLE and HIGH automatically for printing.
Cursor can be moved with [left] and [right] keys, and the heads can be turned ON/OFF
with [up] and [down] keys. Press [ENTER] key to start the test print of the selected
heads. It returns to the former menu by pressing [left] key when the cursor is on the
left end.
BI-DIR.DEFAULT H1 H2
DT1, Low 2
BI-DIR.DEFAULT H1 H2
DT3, Low 2
BI-DIR.DEFAULT H1 H2
DT1, Middle 2
BI-DIR.DEFAULT
H1 H2
DT3, Middle 2
BI-DIR.DEFAULT H1 H2
DT1, High
2
BI-DIR.DEFAULT
H1 H2
DT3, High 2
Cursor can be moved with [left] and [right] keys, and value can be selected with [up] and [down] keys.
The value being selected is marked with an under bar. It returns to the former menu by pressing [left]
key when the cursor is on the left end.
Default: It can be changed starting from the standard value (15) with [up] and [down] keys.
Range: 0 to +60dot (changeable by 0.5dot which is indicated as 1/2.
STANDARD HEAD
3 > 3
4-2
TEST PRINT
TEST PRINT
H2 H3
H5 H6
1 3
2 1
H2 H3 H5 H6
1 3
2 1
H2 H3
H5 H6
1 3
2 1
H2 H3 H5 H6
1 3
2 1
H2 H3
H5 H6
1 3
2 1
H5 H6
H2 H3
1 3
2 1
PERFORMING
TEST PRINT
H4 H5 H6
H3
2 1 3
1 3
H3 H4 H5 H6
1 3 2 1 3
H4 H5 H6
H3
2 1 3
1 3
H4 H5 H6
H3
1 3 2 1 3
H3
H4 H5 H6
1 3
2 1 3
H3
H4 H5 H6
1 3
2 1 3
This menu is hidden normally.
It appears when Base Head Menu is enabled
on Bit6 of PAGE2 in SYSTEM SWITCH menu.