Advertisement
18-14
GROUP 18- TRIM AND SEATS
15.
Pull
the
bottom
corners of
the cover frame and hog r ing
the
cover
to
the
frame.
16. Replace
the two
rear
seat
back buttons and
the rear cover
panel.
17. Install
the
seat back on
the
hinges and tighten the hinge as-
sembly
to seat
cushion
retaining
bolts.
18. Hog ring the seat back lower
valance panel
to
the seat cushion.
19. Replace
the
side valance and
install the
seat
in the
car.
FAIRMONT REAR SEAT
REAR SEAT CUSHION COVER
1. Remove
the
rear seat cushion
from
the
car by lifting on the
front of the seat and pulling
it
forward.
2. Remove the cushion cover hog
ring3 and
turn
back the corner.
Remove the seat cushion buttons.
SEAT BELTS
GENERAL
INFORMATION
The
seat
and
sash
belts are factory
installed
in
their proper locations. If
the seat belts
or
sash
belts are
re-
moved for
any
reason, they
should
be
installed
as shown
in
Fig.
9
&
10.
I
I'
3. Remove
rear seat cushion
pad
assembly, upper and lower.
4. Inspect
the
pad assembly and
spring assemblies and repair or
re-
place as necessary.
5.
Transfer the listing
wires
to
the
new
cover.
6. Replace
pad assemblies,
upper
and lower.
7. Replace
the
seat
cushion
but-
ton:s and hog ring
the corner in
position.
Replace
the cushion in
the
car.
REAR SEAT BACK COVER
1.
Remove
the
rear seat
cushion
and undo
the two
screws
holding
thP. lower end of the rear seat
back
in
the
car.
2. Lift
the
seat back to
disen-
gage it from the uppP.r hooks and
remove the seat back from the
car.
3. Undo the hog rings retaining
the lower filler flap and remove
it
from the seat back.
4. Undo the hog rings retaining
Sealer should be placed
around all
seat
belt
anchor
bolt holes in the
floor pan.
Belt
assemblies
must be installed in
matched
sets as received
and must
not be interchanged between models
.
The position
of
inboard front
seat
belts
at
the
tunnel
shall be pointing
in
a forward
direction
,
plus
or
minus
the upper filler flap and remove the
bolts holding the
armrest assembly
in
position. Remove the armrest by
drawing it back through the seat.
5. Remove
the seat back buttons
and all hog
rings retaining the seat
back
cover.
6. Remove
pad assembly.
7. Inspect
the pad and spring as-
semblies
and repair or replace
83
necessary.
8.
Transfer the listing wires to
the new cover.
9. Replace
pad assembly.
10. Hog ring the seat back cover
in
position.
11. Replace
the armrest and hog
ring the upper filler flap
in
position.
12.
Hog
ring the lower filler flap
in place.
13.
Engage
the seat back on the
upper hooks and replace
the two
seat back attaching
screws.
14. Replace
the rear
seat
cushion.
15 degrees
.
If
a component
portion
(buckle por-
tion, retractor portion.
etc) of a
seat
belt
or sash
belt
assembly is non
functional or
damaged
the entire
assembly
(buckle,
tongue
and
shoulder
harness portions) must
be
replaced.
V6W~
S'TD
J!lt.
7J
0Nl
V
'Ottt./IIQCW'"UIIIII"N~
.-Loot
,..,n,
Jr&J
~#lrJ
o.._,
BOLT
J
MCMJLD:;:Jt
BOLT -
-
/
16"
1
I 1
'8"
BOLT
J
MOI..rUD
..;
Pit
,
MG
V~
;
KEI
'('
16
PL.f.
"'
" • " ' " '
WAV'
.
,'.
l:.
t1f..R
"'
i'l!"t:R
......
~'
$
l/r1'A1If
OtlfPIT
.-tCIOf'
,...,.n
BELT
&3::i!,
COMI,
RT. SU.f
BELT .lS..OT.
PaT.
lJ!!
.t.T
t.A.P
aol.T
s.auu.a
..;
PACD
FIG. 9-
Seat Belt Installation
Advertisement
