Advertisement
17-38
GROUP
17-
BODY, DOORS AND WINDOWS
R.P.O.
DOOR VENT WINDOW FRAME
1.
Remove
the door trim panel and
the watershield.
2.
Remove the i:mer and
outer
door belt line weatherstrips
by prying
them loose from the
door.
3.
Remove
the
window lower
stop (power windows) and completely
lower the door window.
4. Remove the
front
glass run
adjusting bolt,
lock
nut
and washer.
5.
Remove the
front glass run
from the division
bar retainer at
the vent frame
by
sliding
the run
down and removing
it from the
door through the inner panel
access
hole
.
6. Remove
the
three
screws
re-
taining
the vent frame
to the door
frame
.
Remove the vent
window
assembly and place it
on a bench
.
7. Remove the screws
retaining
the upper vent pivot
to the
vent
frame
assembly.
Remove the nut
retaining the lower
pivot bolt
and
remove the spring nylon
bushings,
washer and stop washer.
8. Remove
two screws
from
the
top
of the assembly and
remove the
four rivets retaining
the
vent
frame
and division bar
weatherstrip.
Sepa-
rate the frame and
division
bar.
9
.
Using suitable tool,
remove the
glass. Remove the weatherseal.
INSTALLATION
1. Position
new weatherseal to
the vent glass.
2.
Lubricate
the weatherseal with
rubber lubricant
and
seat
the glass
assembly in
its
channel.
3. Position the division bar to
the vent frame
.
Position the
vent
frame and division
bar weatherstrip
and install
the four
rivets and
two
screws at the top of
the frame.
4.
Assemble
the
vent
tension
spring to
the lower pivot
and adjust
the pivot spring
tension
so
that the
window will stay
open
at
highway
speeds.
5. Position the
frame
assembly on
the door and
install the three retain-
ing
screws.
6. Position
the glass front run in
the door and slide it
into the vent
frame retainer.
7.
Loosely install
the
front
run
adjusting bolt and
nut.
8. Raise the window
halfway
and
loosely in stall the lower
glass
stop.
9. Adjust the front run and
tighten the retaining
nut.
10. Lower the window so that
the top of
th~
glass is le·1el with the
window opening belt line.
11. Install the belt line weather-
strips.
12. Install the door watershield
and trim panel.
FRONT DOOR GLASS-
REMOVAL
1.
Remove the trim panel and
position the water shield away from
the access
holes.
2.
After removing the
stop,
lower the glass until the regu-
lator arm roller
is
out of the glass
channel.
3. Unsnap and remove the belt
weatherstrips, loosen the front run
attaching
bolt
at
the
mounting
bracket, and remove the bracket
attaching bolt from the inner panel.
4. Remove the front run from
the division bar by pulling rearward
on the edges of the run.
5. Remove the glass.
INSTALLATION
l. Disconnect
the glass
retainer
and
remove the
channel
from the
glass.
2. Install
the channel,
using new
retainers.
3.
Simultaneously, position the
glass
and
run in the door, and install
the belt weatherstrips.
4. Position the regulator
arm
rol-
ler in the
channel.
and finally posi-
tion the run in the division bar.
5.
Connect
the run and bracket,
making necessary lateral adjustment.
6. Install the stop, making neces-
sary adjustment.
7.
Carefully
position the water
shield.
the inner panel, and
install
the trim panel.
FRONT
DOOR WINDOW
REGULATOR
REMOVAL
1. Remove the trim panel and
p~
sition
the water shield away from the
access
holes.
2. Disconnect the regulator from
the glass channel roller.
3. Raise the glass by hand and
secure
it in the raised position.
4. Remove the regulator retaining
bolts (Fig. 3).
and
remove the regu-
lator through the door access hole.
INSTALLATION
1. Position the regulator inside
the door and install the retaining
bolts snugly.
2. Lower the glass and connect
the regulator.
3. Check the operation of the
glass, adjust it if necessary, and
tighten the retaining bolts.
4. Carefully position the water
shield to the inner panel and install
the trim panel.
REAR DOOR GLASS
REMOVAL
l. Remove the door trim panel
and watershield.
2. Remove the two screws retain-
ing
the
regulator
roller channel
bracket to the lower window channel
(Fig.
4)
.
3. Remove the lower stop as-
sembly.
4. Remove the screw and nut re-
taining the rear run retainer and
stationary
glass. Move the run re-
tainer and glass back and down
in
the door.
5. Remove the door belt, outside
w~atherstrip
.
6. Tilt the door window down
and then lift it out of the door.
7.
Disconnect
the glass retainers
and
remove
the glass from the
lower
channel.
INSTALLATION
I. Install the lower
channel on
the
glass
using new retainers.
2. Position the glass and channel
assembly in the door.
3. Position the rear run retainer
and
stationary
glass assembly and
install the retainer screw and nut.
4. Install the regulator roller chan-
nel bracket
on
the window channel.
5. Install the lower window stop.
6. Install the door trim water-
shield
and the door trim panel.
7. Install the window outside belt
weatherstrip.
Advertisement
