Advertisement
18-8
GROUP 18 TRIM AND SEATS
FIG. 2-Front Seat Cushion
5.
Transfer the listing wires to
the
new cover.
6.
With the seat cushion assembly
right
side up,
make
sure that
the pads
are stacked properly and centered;
then place the
cover over
the pads
to
hold
them in
position.
7.
Carefully turn
the
seat assem-
bly
over so that
the pads do not shift
out of
position.
8.
After
centering
the cover
and
straightening the seams along
the
front edge of the cushion, fasten
the
cover
to
the front of the seat frame
with hog
rings
.
Make sure
that
the
hog
rings encircle
the listing
wire
.
In-
stall I
hog
ring in
e.ach hole provided
in the seat cushion frame
.
9.
At the
rear
of
the
seat assem-
bly. pull the cover
taut
over
the
pads.
and install
hog rings
at the
seat frame
.
10.
Fasten the side of
the
cover
to
the seat frame side with
hog rings
throu~h
the holes provided
(Fig.
2).
11.
In
sta
ll
the
seat
back
12. Install
the seat
tracks to
the
cushion anu the seat assembly
in the
car
.
REAR SEAT CUSHION COVER
1. Remove
the
rear
seat cushion
from the car by lifting on the front of
the seat
and
pulling it forward
.
2. Remove the cushion cover hog
rings and remove the cushion cover
from the
seat
frame.
3. Inspect the pad and replace it
if
necessary
.
4.
Transfer the listing wire to the
new cushion
cover.
5. Position the new cushion cover
on the seat
frame
and springs and at-
tach it in place
with
hog rings
1
Fig.
4)
6. Install the
seat
cushion in the
car.
NOTE
Two types
of
rear
seat and
se~t
back
springing
are
employed
and, 1f
replacement
of a frame
and
spring
assembly
is required, it must be of
the
same
type
as
that removed.
FRONT SEAT BACK COVER
Repairs to
seat
backs are per-
formed
out
of
the car and are
usually limited to replacement of
torn
or
burned
seat
covers. In a few
instances,
the pads may be damaged
and
require replacement.
Fig. 3 shows a front seat back
build-up.
1.
Remove the seat back.
2. Remove
the
ash receptacle and
ash receptacle
retainer,
if
equipped
.
3. Remove the hog rings retain-
ing
the
seat
back cover to the frame.
Unhook the listing wires from the
seat spring assembly
tabs, and re-
move the cover
(Fig.
3)
4. Transfer the listing wire to the
new
seat
back cover.
S. Inspect the
seat
pad and spring
assemblies, and repair or
replace
as
necessary
6.
Careiully
place the cover over
the
seat
frame
and
pad
assembly.
Pull the cover
taut
over the pads,
hook the listing wires on the seat
spring assembly tabs and install the
hog rings
(Fig.
3)
7. Cut a hole in the cover for the
ash receptacle retainer, if equipped,
and install the receptacle assembly.
8. Install the seat back to the seat
cushion
.
REAR SEAT BACK COVER
I. Remove the rear seat back
from the car.
2.
Remove the hog rings retaining
the seat back cover to the frame and
remove the rear
seat
back cover.
3. Transfer the listing wires' to the
new
cover.
4. Position the new cover on the
pad
and seat
frame and secure it in
place with hog rings
(Fig.
5)
5. Install the rear
seat
back in
the car.
Advertisement
