Advertisement
18-6
Section
PART
18-2
SEATS
Pare
Section
Pare
1
~nch
Seats
-
Removal and Installation
Seat
and
Seat Track
....
18·6
18·6
18-6
18-6
18-6
18·8
18-8
Rear Seat Back Cover
.
.
..
....
..
..
.. .. ....
.. ..
18··8
Front Seat Cushion and Back
Rear Seat Cushion and Back
Front Seat
Cushion
Cover
Rear
Seat
Cushion
Cover
Front Seat
Back Cover
D
BENCH SEATS
REMOVAL AND INSTALLATION
SEAT AND SEAT TRACK
Work,
other than that of minor
nature,
is
more easily performed
when the front
seat
assembly is
removed
from
the car.
1.
Remove the nuts retaining the
seat
tracks to the floor pan. Lift
the
seat assembly
from the car
(Fig.
I)
and disconnect and remove
the release cable.
2. Remove the
seat
tracks from
the
seat frame.
3. Transfer the
seat
adjusting
lever knob
and
the retracting
springs,
if necessary, to the new track
assembly.
4. Position the seat tracks on the
seat frame and
install the retaining
bolts
and
release cable.
5. Position the
seat
assembly in
the
car and
install the retaining bolts
and nuts.
Release Cable Adjustment. Re-
lease
cable
maladjustment will af-
fect only the
side
of the seat. In
case
the latch retaining the track
fails to release, turn the release
cable
turnbuckle or eye bolt enough
turns to
shorten
the release cable
travel
sufficiently
to release the
track
latch. If the latch fails to
secure
the
seat
travel, turn the
release cable turnbuckle or eye bolt
to
lengthen
the
release cable enough
to allow the latch to
snap
in the
locking position.
2 Bucket Seats -
Removal and Installation
Front Seat and Seat Track
..
.. .. ..
18·11
18-11
18·11
18-12
18-14
.18-14
Front Seat Cushion Cover
Front Seat Back Cover ..
..
..
..
Rear Seat Cushion Cover
Seat Belts- General Information
FRONT SEAT CUSHION
AND/OR BACK
1. Remove the front seat and seat
track from the car if the cushion is to
be replaced.
2. To replace the seat cushion,
remove the seat assembly from 'the
seat track.
3. Remove the bolts and washers
attaching the seat back to the seat
cushion frame. Before being able
to remove the attaching bolts, it is
necessary to remove the seat backs
and seat cushion trim from the
bolts.
4. Position the seat back assem-
bly on the seat. Install the bolts
and washers
attaching the seat
back to the seat and fasten the
seat back and seat cushion cover
trim with hog rings.
5. Position the seat cushion on the
seat track and install the retaining
bolts if removed.
6. Install the front seat and seat
track in the car.
REAR SEAT CUSHION
AND/OR BACK
1.
Lift the front edge of the rear
seat cushion and pull it forward to
remove it from the car.
2. Remove 2 rear seat back attach-
ing screws located at the bottom of
the seat back.
3. Lift up on the seat back to dis-
engage the seat from the upper
hooks and remove the seat back from
the car.
4. Position the seat back in the car
and engage the seat with the upper
hooks.
5. Install the seat back lower
retaining screws. Then install the
rear seat cushion.
FRONT SEAT CUSHION
COVER
Fig. 2 shows a front seat cushion
build-up. Seat cushions for all models
are built-up in basically the same
manner. Therefore, when installing
new seat cushion covers or pads,
refer to Fig. 2 for the location of
listing wires, hog rings, anti-squeak
pads, and seat pad stack-up.
1.
Remove the seat and seat track
assembly.
2. Remove the bolts and washers
attaching the seat back to the
seat
cushion frame.
3. Remove the
seat
back assem-
bly.
4. Remove the hog rings retaining
the seat cushion cover and remove
the cover
(Fig.
2). Inspect the pad
and replace it if necessary.
Advertisement
