Siemens SINUMERIK 840D sl Programming Manual page 12

Table of contents
6.3.8 Measuring drills - special applications (from measuring cycles SW 6.3) ................................ 6-55
6.4 CYCLE973 Calibrating workpiece probes................................................................................ 6-56
6.4.1 Function overview .................................................................................................................... 6-56
6.4.2 Calibrating in the reference groove.......................................................................................... 6-59
6.4.2.1 General information.................................................................................................................. 6-59
6.4.2.2 Programming example ............................................................................................................. 6-61
6.4.2.3 Operational sequence .............................................................................................................. 6-62
6.4.3 Calibration on surface .............................................................................................................. 6-62
6.4.3.1 General information.................................................................................................................. 6-62
6.4.3.2 Programming example ............................................................................................................. 6-64
6.4.3.3 Operational sequence .............................................................................................................. 6-65
6.5 CYCLE974 workpiece: 1-point measurement.......................................................................... 6-66
6.5.1 Function overview .................................................................................................................... 6-66
6.5.2 1-point measurement and ZO determination ........................................................................... 6-69
6.5.2.1 General information.................................................................................................................. 6-69
6.5.2.2 Programming example ............................................................................................................. 6-70
6.5.2.3 Operational sequence .............................................................................................................. 6-71
6.5.3 1-point measurement and tool offset ....................................................................................... 6-71
6.5.3.1 General information.................................................................................................................. 6-71
6.5.3.2 Programming example ............................................................................................................. 6-73
6.5.3.3 Operational sequence .............................................................................................................. 6-75
6.5.4 1-point measurement with reversal and tool offset .................................................................. 6-75
6.5.4.1 General information.................................................................................................................. 6-75
6.5.4.2 Programming example ............................................................................................................. 6-77
6.6 CYCLE994 workpiece: 2-point measurement.......................................................................... 6-79
6.6.1 Function overview .................................................................................................................... 6-79
6.6.1.1 General information.................................................................................................................. 6-79
6.6.1.2 Programming example ............................................................................................................. 6-83
6.6.1.3 Operational sequence .............................................................................................................. 6-86
6.7 Complex example for tool measurement ................................................................................. 6-88
7 Miscellaneous functions.......................................................................................................................... 7-1
7.1 Log measurement results........................................................................................................... 7-1
7.1.1 Overview of the logging cycles................................................................................................... 7-1
7.1.2 Log file........................................................................................................................................ 7-1
7.1.3 Handling the log cycles .............................................................................................................. 7-2
7.1.3.1 General information.................................................................................................................... 7-2
7.1.3.2 CYCLE100 Logging ON ............................................................................................................. 7-2
7.1.3.3 CYCLE101 Logging OFF ........................................................................................................... 7-2
7.1.3.4 CYCLE105(PAR1) Creating log content .................................................................................... 7-3
7.1.3.5 CYCLE106(PAR1) Logging sequence control ........................................................................... 7-3
7.1.3.6 CYCLE113(PAR1,PAR2) Read system date and time.............................................................. 7-3
7.1.3.7 CYCLE118(PAR1,PAR2,PAR3,PAR4,PAR5)............................................................................ 7-3
7.1.3.8 Programming example for formatting a single number.............................................................. 7-4
7.1.3.9 Programming example for formatting three numbers ................................................................ 7-4
7.1.4 Variables when logging .............................................................................................................. 7-5
7.1.5 Selection of the log content........................................................................................................ 7-6
7.1.6 Log format .................................................................................................................................. 7-7
7.1.7 Log header ................................................................................................................................. 7-8
7.1.8 Example: Creating a measurement result log............................................................................ 7-9
7.2 Measuring cycle support in the program editor (up to measuring cycles SW 5.4) .................. 7-12
7.2.1 Measuring cycle support files................................................................................................... 7-12
7.2.2 Load the measuring cycle support ........................................................................................... 7-13
7.2.3 Assigning calls and measuring cycles ..................................................................................... 7-13
xii
Programming Manual, Release 04/2006, 6FC5398-4BP10-0BA0
Measuring cycles