D11: Multitap Cho/Delay (Multitap Chorus/Delay) - Korg KROSS Parameter Manual

Effect Guide
D11: Multitap Cho/Delay (Multitap
Chorus/Delay)
This effect has six chorus blocks with different LFO phases. You
can produce a complex stereo image by setting a different delay
time and depth for each block. You can control the delay output
level via a modulation source.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
+
Right
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
LFO: Triangle
D -mod
On/Off Control
Paramter
Tap1
Tap1 [ms] Delay (000)
[ms]
Dep Tap1 Depth
Status Tap1 Status
Tap2
Tap2 [ms] Delay (180)
[ms]
Dep Tap2 Depth
Status Tap2 Status
Tap3
Tap3 [ms] Delay (060)
[ms]
Dep Tap3 Depth
Status Tap3 Status
Tap4
Tap4 [ms] Delay (240)
[ms]
Dep Tap4 Depth
Status Tap4 Status
Tap5
Tap5 [ms] Delay (120)
[ms]
Dep Tap5 Depth
Status Tap5 Status
Tap6
Tap6 [ms] Delay (300)
[ms]
Dep Tap6 Depth
288
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap4 Delay
Tap5 Delay
Tap6 Delay
Panning Preset
Value Explanation
Sets the Tap1 (LFO
0...650 phase=0 degrees)
delay time
Sets the Tap1 chorus
0...30
depth
Selects on, off, or
Always On,
modulation source
Always Off,
for the control of Tap1
On→Off ,
output
Off→On
p.288
Sets the Tap2 (LFO
0...650 phase=180 degrees)
delay time
Sets the Tap2 chorus
0...30
depth
Selects on, off, or
Always On,
modulation source
Always Off,
for the control of Tap2
On→Off (Dm),
output
Off→On (Dm)
p.288
Sets the Tap3 (LFO
0...2000 phase=60 degrees)
delay time
Sets the Tap3 chorus
0...30
depth
Always On,
Selects on, off, or
Always Off,
modulation source
On→Off
for the control of Tap3
(Dm),
output
Off→On
p.288
(Dm)
Sets the Tap4 (LFO
0...2000 phase=240 degrees)
delay time
Sets the Tap4 chorus
0...30
depth
Always On,
Selects on, off, or
Always Off,
modulation source
On→Off
for the control of Tap4
(Dm),
output
Off→On
p.288
(Dm)
Sets the Tap5 (LFO
0...2000 phase=120 degrees)
delay time
Sets the Tap5 chorus
0...30
depth
Always On,
Selects on, off, or
Always Off,
modulation source
On→Off
for the control of Tap5
(Dm),
output
Off→On
p.288
(Dm)
Sets the Tap1 (LFO
0...2000 phase=300 degrees)
delay time
Sets the Tap6 chorus
0...30
depth
Status Tap6 Status
LFO Freq
LFO [Hz]
[Hz]
Panning
Pan Preset
Preset
Tap1
Feedback
Feedback
Wet / Dry
Src Source
Amt Amount
Wet / Dry
←
Wet/Dry
Src Source
Amt Amount
Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (dm): Output level is switched from on to off depending
on the modulation source.
Off→On (dm): Output level is switched from off to on depending
on the modulation source.
Combining these parameters, you can change from 4-phase chorus
to two-tap delay by crossfading them gradually via the modulation
source during a performance.
Panning Preset
This parameter selects combinations of stereo images of the tap
outputs.
Always On,
Selects on, off, or
Always Off,
modulation source
On→Off
for the control of Tap6
(Dm),
output
Off→On
p.288
(Dm)
Sets the speed of the
0.02...13.00
LFO
1 : L 1 2 3 4 5 6 R Selects the stereo
2 : L 135 246 R panning pattern for
3 : L 1 3 5 2 4 6 R each tap
4 : L 1 4 5 6 3 2 R p.288
Sets the Tap1
–100...+100
feedback amount
Selects the
modulation source
for the Tap output
Off...Tempo
level, feedback
amount, and effect
balance
Sets the modulation
–100...+100 amount of Tap1
feedback amount
Sets the balance
Dry, 1 : 99...
between the effect
99 : 1, Wet
and the dry input
Selects a modulation
Off...Tempo
source for Wet/Dry
Sets the modulation
–100...+100
amount for Wet/Dry