Chorus, Flanger, And Phaser (Cho/Fln Phaser) - Korg pa 900 User Manual

Chorus, Flanger, and Phaser (Cho/Fln
Phaser)
26: Stereo Chorus
This effect adds thickness and warmth to the sound by modulat-
ing the delay time of the input signal. You can add spread to the
sound by offsetting the phase of the left and right LFOs from
each other.
Stereo In - Stereo Out
Left
LEQ HEQ
EQ Trim
LEQ HEQ
EQ Trim
Right
LFO: Tri / Sine
LFO Waveform Triangle, Sine
a
LFO Phase
–180...+180
[degree]
LFO Frequency
0.02...20.00
[Hz]
b Src Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync Off, On
MIDI,
BPM 40.00...
c
300.00
Base Note r...w
Times x1...x32
L Pre Delay
0.0...50.0
[msec]
d
R Pre Delay
0.0...50.0
[msec]
Depth 0...100
Src Off...Tempo
e
Amt –100...+100
f EQ Trim 0...100
Low,
Pre LEQ Fc
Mid-Low
g
High,
Pre HEQ Fc
Mid-High
Pre LEQ Gain
–15.0...+15.0
[dB]
h
Pre HEQ Gain
–15.0...+15.0
[dB]
-Wet, -
Wet/Dry 1:99...Dry...99:1
, Wet
i
Src Off...Tempo
Amt –100...+100
d: L Pre Delay [msec]
d: R Pre Delay [msec]
Setting the left and right delay time individually allows you to
control the stereo image.
FX Amt
Chorus
Chorus
FX Amt
LFO Phase
Selects the LFO Waveform
Sets the LFO phase difference
between the left and right
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the delay time for the left
channel
Sets the delay time for the right
channel
Sets the depth of LFO modulation
Selects the modulation source for
the LFO modulation depth
Sets the modulation amount of the
LFO modulation depth
Sets the EQ input level
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Selects the cutoff frequency (high or
mid-high) of the high-range
equalizer
Gain of the Low EQ
Gain of the High EQ
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source

Chorus, Flanger, and Phaser (Cho/Fln Phaser)

27: Black Chorus/Flanger
This models a Danish-made stereo chorus + pitch modulator &
flanger. Although this effect was originally intended for guitar, it
was also used by numerous keyboard players. Used with electric
piano, it produces a distinctive tone.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
+
Chorus
Input Gain
Right
LFO
Speed [Hz] 0.10...10.0 Sets the LFO speed
Intensity 1...100 Sets the intensity of LFO modulation
Select a mode
0: Chorus
Mode 0, 1, 2
1: Pitch Modulation
2: Flanger
Width 0...2 Sets the LFO modulation depth
Input Gain 1...100 Sets the input gain
Select a output mode
Output Mode 0, 1 0: Mono
1: Stereo
Dry, 1:99 ...
Wet/Dry Balance between the wet and dry signal
99:1, Wet
Table , "Selects a modulation source for
Source Off...Tempo
Wet/Dry, " on page 358
Table , "Sets the modulation amount for
Amount –100 ... +100
Wet/Dry, " on page 358
Mode
Intensity
Increasing the "Intensity" value will strengthen the modulation
effect. This controls the effect, direct, and feedback values. The
values that are controlled will depend on the "Mode" setting.
Effects
373
Wet / Dry
Mode & Intensity
+
Mono
-
+
Output Mode
Stereo
Wet / Dry