Mixer - Korg KROSS Parameter Manual

16–4: MIXER
Pan: #8 Bus Select
Here you can adjust the post-IFX mixer settings.
1 (IFX1)
Pan: #8 (CC#8)
Specifies the panning immediately after the insert effect.
You can use CC#8 to control this.
Bus Select
Specifies the bus where the signal will be sent immediately after
the insert effect.
L/R: The signal will be sent to the L/R bus.
Off: The signal will not be sent directly to the L/R outputs. This
setting is useful if you want to:
• Use Send 1 or Send 2 to route the signal entirely through the
master effects, without sending the dry signal to the outputs.
• Use the FX Control Bus to route the signal to an effects side-
chain, such as a gate or vocoder, without being heard directly at
the outputs.
S1 (Send1)
S2 (Send2)
These adjust the level where the post-IFX signal is sent to master
effects 1 and 2. This is valid if Chain is set to Off.
You can use CC#93 to control the Send 1 level, and CC#91 to
control the Send 2 level. The global MIDI channel specified
by MIDI Channel (G–MIDI> BASIC) is used for these
messages.
FX Control Bus
Sends the post-IFX signal to the FX Control busses. For more
information, please see the "FX Ctrl Bus (FX Control Bus)"
section on page 54.
If you're using FX Control Bus as an input signal for Vocoder
etc., a feedback loop will occur if you output to the same bus
as specified here and oscillation will occur. Set this with care
to avoid creating a loop.
2...5 (IFX2...5)
The parameters for for insert effects 2–5 are exactly the same as
those for insert effect 1. See "1 (IFX1)" above.
16–1...4: FUNCTION
V
• 0: Write Program, Write/Initialize Program
• 1: Solo Setting see page 63
• 2: Compare see page 64
• 3: Auto Song Setup see page 64
• 4: Add to Favorite see page 64
• 5: Copy Insert Effect see page 66
• 6: Swap Insert Effect see page 66
For more information, please see the "Program: Function" section
on page 63.
17: P–IFX
Here you can edit the parameters of the insert effect you selected
in the P–FX ROUTING> IFX page.
17–1: IFX1(Insert Effect1)
FX Control Bus
[L000...C064...R127]
[Off, L/R]
Effect On/Off
This turns the insert effect on and off. It is linked with the on/off
setting in the IFX page.
IFX1 Parameters
This tab shows the parameters for IFX1, as selected on the Insert
FX Setup page.
For details on the specific parameters of each effect, please see
page 217.
[000...127]
[000...127]
17–2: IFX2 (Insert Effect2),
17–3: IFX3 (Insert Effect3),
17–4: IFX4 (Insert Effect4),
17–5: IFX5 (Insert Effect5),
[Off, FC1, FC2]
The parameters for IFX2–IFX5 are the same as for IFX1.
V
• 0: Write Program, Write/Initialize Program
• 1: Solo Setting
• 2: Compare
• 3: Auto Song Setup
• 4: Add to Favorite
• 5: Copy Insert Effect
• 6: Swap Insert Effect
For more information, please see the "Program: Function" section
on page 63.
see page 63
Effect On/Off
Effect dynamic modulation (Dmod) is controlled on the
global MIDI Channel (G–MIDI> BASIC). For more
information, please see the "Dynamic Modulation Source
List" section on page 298.
17–1...5: FUNCTION
see page 63
see page 64
see page 64
see page 64
see page 66
see page 66
17: P–IFX 16–4: MIXER
[Off, On]
see page 63
61