Voice Resonator - Korg KROSS Parameter Manual

036: 2Voice Resonator

This effect resonates the input signal at a specified pitch. You can
set the pitch, output level, and pan settings for two resonators
individually. You can control the resonance intensity via an LFO.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Resonator
Trim
+
Resonance
Resonator
Trim
Right
Invert: On/Off
D -mod
LFO
Control Mode
Manual
Paramter Value
Control Manual, LFO,
Control
Mode Dmod
LFO/Dmod
Mod Invert Off, On
Invert
LFO Freq
LFO [Hz] 0.02...20.00
[Hz]
Dmod
Dmod Src Off...Tempo
Source
BPM/MIDI
MIDI Sync Off, On
Sync
MIDI,
←
BPM 40.00...
300.00
←
Base Note ...
←
Times x1...x32
←
Mod. Depth –100...+100
←
Trim 0...100
Voice1
V1 Pitch C0...B8
Pitch
Voice1
Fine [c] –50...+50
Fine [cents]
Lvl Level 0...100
Voice1
V1 Reso –100...+100
Resonance
High Damp
HDamp[%] 0...100
[%]
L6...L1, C,
←
Pan
R1...R6
Voice2
V2 Pitch C0...B8
Pitch
Fine [c] Fine [cents] –50...+50
Lvl Level 0...100
Voice2
V2 Reso –100...+100
Resonance
Wet / Dry
High Damp
Level
Pan
Level Pan
High Damp
Wet / Dry
Pitch, Fine [cents]
Explanation
Switches the controls
of resonance intensity
p.237
Reverses the Voice 1
and 2 control when
LFO/Dmod is selected
p.237
Sets the speed of the
LFO
Selects the
modulation source
that controls
resonance intensity
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency p.223
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Selects the type of
notes that specify the
LFO speed p.223
Sets the number of
notes that specify the
LFO speed p.223
Sets the amount of
resonance intensity
control via LFO/
Dmod
Sets the input level at
the resonator
Sets the voice1 Pitch
for resonance p.237
Fine-adjusts the voice
1 pitch for resonance
p.237
Sets the Voice1
output level
Sets the intensity of
resonance when
Control Mode =
Manual p.237
Sets the damping
amount of resonant
sound in the high
range p.237
Sets the Voice1 stereo
image
Sets the voice 2 Pitch
for resonance p.237
Fine-adjusts the voice
2 pitch for resonance
p.237
Sets the Voice2
output level
Sets the intensity of
resonance when
Control Mode =
Manual p.237
Single size effects 036: 2Voice Resonator
High Damp
HDamp[%] 0...100
[%]
L6...L1, C,
←
Pan
R1...R6
Dry, 1 :99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Control Mode
Voice 1 Resonance
Voice 2 Resonance
This parameter determines the resonance intensity.
When "Control Mode" = Manual, the "Resonance" parameter sets
the intensity of resonance. If the "Resonance" parameter has a
negative value, harmonics will be changed, and resonance will
occur at a pitch one octave lower.
When "Control Mode" = LFO, the intensity of resonance varies
according to the LFO. The LFO sways between positive and
negative values, causing resonance to occur between specified
pitches an octave apart in turn.
When "Control Mode" = Dmod, the resonance is controlled by the
dynamic modulation source. If P.Bend is assigned as the
modulation source, the pitch an octave higher and lower can be
controlled, similar to when LFO is selected for Control Mode.
LFO/Dmod Invert
When "Control Mode" = LFO or Dmod, the controlled phase of
either Voice 1 or 2 will be reversed. When the resonance pitch is
set for Voice 1 (Resonance has a positive value), Voice 2 will
resonate at a pitch an octave below (Resonance has a negative
value).
Voice 1 Pitch
Voice 1 Fine [cents]
Voice 2 Pitch
Voice 2 Fine [cents]
The Pitch parameter specifies the pitch of resonance by note name.
The "Fine" parameter allows for fine adjustment in steps of cents.
High Damp [%]
This sets the amount of damping amount for the high frequencies
of the resonant sound. Lower values create a metallic sound with a
higher range of harmonics.
Sets the damping
amount of resonant
sound in the high
range p.237
Sets the Voice2 stereo
image
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
237