P–Fx Routing - Korg KROSS Parameter Manual

Hide thumbs Also See for KROSS:
Table of Contents

Advertisement

16: P–FX ROUTING
Here you can adjust settings for the insert effects. For instance,
you can:
• Select the insert effects
• Route a sound to an insert effect
• Create detailed settings for insert effects
For more information, please see "Effect Guide" on page 207.
16–1: BUS
Routing Map
This graphic shows an overview of the insert effects.
Here you can view the status of the input bus to the insert effect
Bus Select, the effect you're editing, and its on/off status and chain
status.
This page lets you adjust the routing of the oscillators to the insert
effects. To adjust the other settings shown in this graphic, please
see "16–3: Insert FX Setup" on page 60.
Bus (Bus Select)
This specifies the output bus for oscillators 1 and 2.
L/R: The oscillators will be output to the L/R bus. Normally you
will choose L/R.
IFX1...5: Output to the IFX1–5 busses.
Off: The oscillator will not be output from the L/R bus, or IFX1–
5. If you want the oscillator output to be connected directly to a
master effect, turn this Off and use the SEND page parameters
Send1 (to MFX1) and Send2 (to MFX2) to adjust the send levels.
FX Control Bus
Sends the output of oscillators 1, 2 to an FX Control bus (two-
channel mono FX Ctrl 1 or 2).
Use the FX Control busses when you want a separate sound to
control the audio input of an effect. You can use two FX Control
busses (each is a two-channel mono bus) to control effects in
various ways.
For more information, please see the "FX Control Bus" section on
page 209.
DKIT-SET (Use DKit Setting)
This is shown and can be edited if the program's Oscillator Mode
is set to Drums.
On (checked): The Bus Select, FX Control Bus, Send 1, and
Send 2 settings (Global DKIT> VOICE) for each key of the
selected drum kit will be used. Check this if you want to apply an
individual insert effect to each drum instrument.
Tip: In most preloaded drumkits, the drum instruments have the
same Bus Select settings according to their type, as follows.
Snares → IFX1
Kicks → IFX2
Other → IFX3
Cymbals→ IFX3
Toms, percussions, and other → IFX4
Off (unchecked): The sound is not output to the L/R bus or the
IFX1–5 buses. Turn this Off if you want the output of the drum
program to be connected directly to a master effect. Use Send1 (to
MFX1) and Send2 (to MFX2) to adjust the send levels.
16–2: SEND
OSC1
Send1 (to MFX1)
Sets the volume (send level) where the output of oscillator 1 will
be sent to master effect 1. This applies only when Bus Select (P–
FX ROUTING> BUS) is set to L/R or Off.
If Bus Select is set to IFX1–IFX5, the send levels to master
effects 1 and 2 are set by Send 1 and Send 2 (P–FX ROUTING>
MIXER) after passing through IFX1–5.
Send2 (to MFX2)
Sets the volume (send level) where the output of oscillator 1 will
be sent to master effect 2.
OSC2
[L/R, IFX1...5, Off]
Send1 (to MFX1)
Send2 (to MFX2)
Sets the volume (send level) where the output of OSC2 will be
sent to master effects 1 and 2 (see "OSC1:").
[Off, FC1, FC2]
[Off, On]
16: P–FX ROUTING 16–1: BUS
CC#93 controls OSC 1/2's Send 1 level, and CC#91 controls
the Send 2 level. These are controlled on the global MIDI
Channel (G–MIDI> BASIC). The actual send level is
determined by multiplying these values with the send levels
of each oscillator.
[000...127]
[000...127]
[000...127]
[000...127]
59

Advertisement

Table of Contents
loading

Table of Contents