Cho/Flng - Mt.dly (Chorus/Flanger - Multitap Delay) - Korg KROSS Parameter Manual

119: Cho/Flng - Mt.Dly (Chorus/
Flanger - Multitap Delay)
This effect combines a mono chorus/flanger and a multitap delay.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Chorus/Flanger
+ Chorus/Flanger
EQ
LEQ HEQ
Trim
Feedback
Right
LFO: Tri / Sine
Paramter Value
Chorus/Flanger
LFO Freq
F LFO[Hz] 0.02...20.00
[Hz]
LFO Tri (Triangle),
LFO
Waveform Sine
F Depth Depth 0...100
Delay Time
Dly[ms] 0.0...50.0
[ms]
F.back Feedback –100...+100
F EQ Trim Pre EQ Trim 0...100
[Low EQ
F LEQ –15...+15
Gain [dB]
High EQ
F HEQ –15...+15
Gain [dB]
–Wet...–1 : 99,
F W/D Wet/Dry Dry,
1 : 99...Wet
Multitap Delay
Tap1
D T1[ms] 0.0...489.0
Time [ms]
←
Tap1 Level 0...100
Tap2
D T2[ms] 0.0...489.0
Time [ms]
Feedback
Fback(T2) –100...+100
(Tap2)
High Damp
HiDamp [%] 0...100
[%]
[Dly]Wet/Dry Dry, 1 : 99...
D W/D
99 : 1, Wet
Src [Dly]Source Off...Tempo
Amt [Dly]Amount –100...+100
–Wet...
←
Wet/Dry –99 : 1, Dry,
99 : 1...Wet
Src Source Off...Tempo
Amt Amount –100...+100
Single size effects 119: Cho/Flng - Mt.Dly (Chorus/Flanger - Multitap Delay)
Wet / Dry
Multitap Delay
Feedback
Delay
(2)
Cho/Flng (1) Mt.Dly
High Damp
Wet / Dry Wet / Dry
Wet / Dry
Explanation
Sets the speed of the
LFO
Selects the LFO
Waveform
Sets the depth of LFO
modulation
Sets the delay time
Sets the feedback
amount
p.257
Sets the EQ input
level
Sets the gain of Low
EQ
Sets the gain of High
EQ
Sets the effect
balance of the
chorus/flanger p.226,
p.257
Sets the Tap1 delay
time
Sets the Tap1 output
level
p.267
Sets the Tap2 delay
time
Sets the Tap2
feedback amount
Sets the damping
amount in the high
range p.266
Sets the multitap
delay effect balance
Selects the Wet/Dry
modulation source
for the multitap delay
Sets the Wet/Dry
modulation amount
for the multitap delay
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
120: Reverb - Gate
This effect combines a mono reverb and a gate.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Reverb
EQ Trim
+ Pre Delay
LEQ HEQ
Right
Input Reverb Mix
Input
Gate+Dmpr
D-mod
Paramter Value
Reverb
Reverb Time
R Time[s] 0.1...10.0
[sec]
High Damp
HiDmp[%] 0...100
[%]
Pre Delay
R Dly[ms] 0...200
[ms]
Reverb Dry, 1 : 99...
Rev Bal
Balance 99 : 1, Wet
R EQ Trim Pre EQ Trim 0...100
Low EQ Low,
R LEQ Fc
Frequency Mid-Low
High EQ High,
R HEQ Fc
Frequency Mid-High
Low EQ Gain
R LEQ [dB] –15.0...+15.0
[dB]
High EQ
R HEQ –15.0...+15.0
Gain [dB]
Gate
Envelope
G Env Sel Dmod, Input
Select
Src Source Off...Tempo
G Thresh Threshold 0...100
←
Polarity +, –
Input Reverb Dry, 1 : 99...
InMix
Mix 99 : 1, Wet
←
G Attack 1...100
←
Release 1...100
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Wet / Dry
Gate
Reverb
Reverb
Balance
Wet / Dry
Envelope - Control
Envelope Select
Gate
Explanation
Sets the reverber-
ation time
Sets the damping
amount in the high
range
Sets the delay time of
the reverb sound and
gate control signal
Sets the reverb effect
balance
Sets the EQ input
level
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
Sets the gain of Low
EQ
Sets the gain of High
EQ
Switches between
modulation source
control and input
signal control p.282
Selects the
modulation source
that controls the gate
when Envelope Select
is set to Dmod p.282
Sets the gate
threshold level p.282
Switches between
non-invert and invert
of the gate on/off
state p.220
Sets the balance
between the dry and
reverb sounds of the
gate control signal
p.282
Sets the attack time
p.220
Sets the release time
p.220
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
281