Korg KROSS Parameter Manual page 147

a. If the MIDI Channel of multiple tracks used by the
arpeggiator is set only to 01, refer to the lines for "01 only." If
the MIDI Channel settings are 01 and one other channel, such
as 01 and 02, then refer to the lines for "01 02, etc." If the
MIDI Channel settings are 01 and multiple other MIDI
channels, such as 01 and 02 and 03, then refer to the line for
"01 02 03, etc."
b. Correction is necessary only if the tracks used by a single
arpeggiator are using only MIDI Channel 01. In some cases,
correction may also be necessary if the two arpeggiators use
the same MIDI channel.
Depending on the combination settings, it may also be
necessary to change the track settings as well.
The preceding illustration shows the example of copying the
combination "SYNTH PAD 039 (C013): Reed Rhythm" with
Auto adjust Arp setting for Multi REC un-checked in Copy
From Combination. Select a new song, and execute the copy to
see the result. (For more about the arpeggiator settings in this
combination, see page 84.)
Using these settings as an example, determine whether correction
is necessary, and if so, what needs to be corrected.
Arpeggiator Run A and B are checked, and MIDI Channel 01
and 02 are selected. Correction is necessary for one of the
arpeggiators. If you execute multi-track recording with these
settings, T01–T06 will have the same MIDI channel, meaning that
the synth pad played from the keyboard (T05) and the performance
data for the rhythmically gated synths played by arpeggiator A
(T01, 02, 03, 04, 06) will be combined, and your performance will
not be reproduced when you play back. T15 is a dummy track used
to trigger arpeggiator A.
1. So that the rhythm performance data of the gated notes
generated by arpeggiator A will be recorded separately,
change the MIDI channel of T06.
Select the S–TRACK> MIDI page, and change the T06 MIDI
Channel to 03.
2. Add settings for triggering arpeggiator A.
For track 12 (or any unused track), turn Status Off, and set the
MIDI Channel to 01. (T12 will be a dummy track used to trig-
ger arpeggiator A.)
3. Select the S–ARP> ASSIGN page. Set the track 12 Assign
to A.
This will produce the following settings.
Track T01 T02 T03 T04 T05
Assign Off Off Off Off Off
Status INT INT INT INT INT
MIDI Ch. 01 03 01 01
This completes the corrections. In the Sequencer P0: Play/REC–
Preference page, set Track Select to any track whose MIDI
channel is 01. Check the Multi REC check box and perform
multi-track recording (REC tracks T01, 06, 07, 10, 16).
T06 T07 T08 T09 T12 T16
A B B B A
INT INT INT INT Off Off
01 03 02 02 02 01 01
Sequencer: FUNCTION Copy from Program
Copy from Program
Copy from Program is available on all of the tabs under the SEQ,
S–INPUT/CTRL, S–LOOP/TONE, S–TRACK, S–ZONE/
DELAY, S–MIDI FILTER, S–ARP, S–DRUM TRACK, S–STEP
SEQ, S–FX ROUTING pages.
This command copies settings from the program you specify to the
currently selected song.
This is the same function as in Combination mode; for details,
please see "Copy from Program" on page 95.
This command in Sequencer mode differs from its behavior in
Combination mode in that the channels assigned to the tracks of
the song will be preserved regardless of the with Arp setting of
the copy-destination track's MIDI Channel. (See step 4.)
Load Template Song
Load Template Song is available on all of the tabs under the SEQ,
S–INPUT/CTRL, S–LOOP/TONE, S–TRACK, S–ZONE/
DELAY, S–MIDI FILTER, S–ARP, S–DRUM TRACK, S–STEP
SEQ, S–FX ROUTING pages.
This command loads a template song.
The built-in sequencer contains sixteen different preset template
songs (P00–15) that contain settings for programs and effects
appropriate for various musical styles. You are also free to create
your own favorite settings for programs, track parameters, and
effects, and save them as one of sixteen user template songs
(U00–15). For more information, please see the "Save Template
Song (Save as User Template Song)" section on page 140.
1. In From, specify the template song that you wish to load.
2. If you check Copy Pattern to Track too?, the Copy Pattern
To Track dialog box will appear automatically after Load
B
Template Song has been executed.
If you execute without checking this, only the template song
you specified in step 2 will be loaded.
When you execute, song settings other than Play Loop will be
copied.
If in step 2 you checked Copy Pattern to Track too? and
pressed the OK button, the Copy Pattern To Track dialog box
will appear.
Use the From field to select the drum pattern that you want to
copy.
Press the SEQUENCER
selected pattern will play.
This dialog box is the same as in the function Copy To Track.
3. In To Track, select the copy destination track.
(START/STOP) button; the
139