Korg KROSS Parameter Manual page 318

Appendices
CC#
85...88 Controller (CC#85...88)
89, 90 –
91 Effect depth 1 (send 2 level)
Effect depth 2 (Insert Effect 1–5 On/
92
Off)
93 Effect depth 3 (send 1 level)
Effect depth 4 (Effect On/Off for
94
master effect 1/2)
95 –
96 Data increment
97 Data decrement
98 NRPN(LSB)
99 NRPN(MSB)
100 RPN(LSB)
101 RPN(MSB)
102...119 –
You can assign any control change number (CC#00–119) to the
ARP control. In this case, buttons will transmit values of 0 (Off) or
127 (On).
*1 In the KROSS sequencer, bank select messages are normally
specified as program change events ("MIDI Event Edit").
However in some cases this will be insufficient when you wish
to change banks on an external device. In such cases, you can
use CC#00 and CC#32 to specify the banks.
For information on the relation between bank select numbers
and the banks of your external device, refer to the owner's
manual for your external device.
*2 Unlike conventional control changes, pitch bend range, fine
tune, and coarse tune settings are made using RPC (Registered
Parameter Control) messages. In Program, Combination, and
Sequencer modes, you can use RPC messages to control the
bend range and tuning for each program, Timbre
(Combination), or Track (Sequencer).
The procedure is to use an RPN (Registered Parameter Num-
ber) message to select the parameter that you wish to edit, and
then use Data Entry to input a value for that parameter. To
select the parameter, use CC#100 (with a value of 00...02) and
CC#101 (with a value of 00). use CC#06 and CC#38 to enter
the data.
The data entry values for each parameter and the corresponding
settings are as follows.
310
Control Value
0...127
–
0...127
0...63(Off),
64...127(On)
0...127
0...63(Off),
64...127(On)
–
0
0
–
–
0
1
2
0
–
for controlling AMS or Dmod
–
send 2 level
turn Insert effect 1...5 on/off
send 1 level
Effect On/Off for master effect 1/2
–
LSB of NRPN
MSB of NRPN
selects the pitch bend range
controls Fine Tune
controls Coarse Tune
MSB of RPN
–
RPN=0 (Pitch bend range)
CC#06 CC#38 Parameter value (Semitone steps)
0 00
12 00
00
24
00
127
RPN=1 (Fine tune)
CC#06 CC#38 Parameter value (1 cent steps)
00
0
00
64
127 00
127 127
RPN=2 (Coarse tune)
CC#06 CC#38 Parameter value (Semitone steps)
0 00
00
40
64 00
88 00
127 00
For example, if in Sequencer mode you wish to set a MIDI
track that is receiving channel 1 to a transpose (coarse tuning)
value of –12, you would first transmit [B0, 64, 02]
(64H=CC#100) and [B0, 65, 00] (65H=CC#101) to the
KROSS to select the RPN coarse tune. Then you would set this
to –12 by transmitting [B0, 06, 34] (06H=CC#6), 34H=52 (cor-
responds to –12), and [B0, 26, 00] (26H=CC#38, 00H=0).
*3 The volume of the KROSS is determined by multiplying the
Volume (CC#07) with the Expression (CC#11). In Sequencer
mode when you stop the song playback and return the location
to the beginning of the track, the Volume will be set to the
starting value, and the Expression will be set to the maximum
value (127).
*4 A value of 64 will correspond to the value specified by the
program parameter. 0 is the minimum, and 127 is the
maximum. Changing from 63–1 or from 65–126 will adjust the
effect from the program parameter setting toward the minimum
Function
0
+12
+24
+24
-100
0
+98
+99
-24
-24
0
+24
+24
*5
*5
*2
*2
*2