Prog (Track Program ) - Korg KROSS Parameter Manual

0–2: PROG (Track Program )
Category/Program
Select
Location
Track
Info
Location
This display shows the current position in the song.
(see page 103)
Song Select
Select the song that you want to record or play back.
(see page 103)
SMP (PAD SAMPLER) On/Off
This specifies whether track 15 is used for the pad sampler or as a
conventional track.
(see page 104)
STEP (STEP SEQ On/Off)
This specifies whether track 16 is used for the step sequencer or as
a conventional track.
(see page 104)
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons   to switch tracks. The
selected track is called the "active track," and is indicated by
square brackets [ ].
Note: If the song is stopped, this is synchronized with Track
Select.
Status
This sets whether the Track controls the internal sounds, external
MIDI devices, or both.
When controlling external MIDI devices, it also allows you to
choose the internal Bank Select numbers (as set by the front-panel
buttons), or use custom Bank Select settings to match the external
device.
Off: Use this to disable the Track. With this setting, the Track's
Program will not sound, and MIDI data will not be transmitted.
INT: The track will sound when you play back the performance
data recorded on the MIDI track. If you use Track Select to select
a MIDI track that is set to INT, the KROSS's sound generator will
produce sound when played. MIDI data will not be transmitted to
an external device.
BTH: Both INT and EXT are operative. When the musical data
recorded in the MIDI track is played back, or when you select a MIDI
track that is set to BTH and play the controllers of the KROSS, the
internal tone generator of the KROSS will sound, and MIDI data will
also be transmitted to an external device.
EXT: When the musical data recorded in the MIDI track is played
back, or when you select a MIDI track that is set to EXT and play
the controllers of the KROSS, MIDI data will be transmitted to an
external device, but the internal tone generator of the KROSS will
not sound.
When you select another song or return to the beginning of the
song, the program change, volume, pan pot, portamento, sends 1
and 2, post IFX pan, and post IFX sends 1 and 2 of each MIDI
track set to EXT will be transmitted via MIDI. (See G–MIDI>
OUT: SEQ Mode "Track MIDI Out" on page 162)
STEP SEQ On/Off
PAD SAMPLER
Song Select
On/Off
[001:01.000...999:16.479]
[000...127]
[Off, On]
[Off, On]
[Off, INT, BTH, EXT, EX2]
0: SEQ 0–2: PROG (Track Program )
EX2: The values of Bank Select MSB and Bank Select LSB (S–
TRACK> MIDI) will be effective. Instead of the program bank
numbers A–g(d) that can be selected on the KROSS, the bank
number specified by Bank Select will be transmitted via MIDI.
The rest is the same as for EXT.
MIDI data is transmitted and received on the MIDI channel
that is specified separately for each MIDI track by the MIDI
Channel.
Keyboard,
Status Sequencer, & MIDI In
play Internal Sounds
OFF No
INT Yes
EXT No
EX2 No
BTH Yes
Category: Index No.
Program Select
Selects the program that will be used by each MIDI track.
The lower line displays part of the program name.
The program that you select here will be used when the song is
played or recorded from the beginning. If the program is changed
while recording, the program change will be recorded as MIDI
data, and the program will change during playback. You can also
change the program manually during playback. However, the
program will change at any point where program change data is
already recorded.
Note: You can't select a program if Pad Sampler On/Off is on.
If the Status is either INT or BTH, programs can be selected
by receiving MIDI program change messages. Also, when
the song is changed or when the song returns to the
beginning, tracks where the Status is EXT, EX2 or BTH will
transmit the bank and program numbers via MIDI. Tracks
where the Status is EX2 will show Bank as "–" and will
transmit the bank number that was selected in the Bank
Select (S–TRACK> MIDI) parameter. (see "Track MIDI
Out" on page 162)
Various ways to change the program for a track
• Choose Program Select, and turn the VALUE dial.
• If you've chosen Program Select and use the sound select list
(see "Sound select list" on page 70).
• Transmit MIDI program change messages from a connected
external MIDI device (if the track Status is INT or BTH).
Note: MIDI program changes are transmitted using the Bank No.
that's specified in Program mode. This is a different number than
the Category Index No. shown on this page. Please be aware of
this.
• You can also use the above methods to switch programs while
a song is playing. If you switch programs while recording, the
program change data will be recorded, and the program will
switch at that point in the song during playback. You can also
use the function Event Edit to add program change data to a
track.
Track Info.
Shows the settings of tracks 1–16 for the parameter that you're
editing.
Note: If this is disabled because of the setting of another
parameter, "–" is shown.
Keyboard & Sequencer Transmit
MIDI Out
No
No
Yes (using the Bank Select message of the
track's Program)
Yes (using the Bank Select message specified
on the MIDI tab of the Track Param page)
Yes
[PIANO...USER: 000...127]
[Program name]
105