St.multimodefltr (Stereo Multi Mode Filter) - Korg KROSS Parameter Manual

Effect Guide
←
Wet/Dry
Src Source
Amt Amount
Phase [deg]
Offsetting the left and right phases alters how modulation is
applied to the left and right channels, creating a swelling effect.
–180
LFO Waveform
LFO Freq [Hz]
Step Freq [Hz]
When "LFO Waveform" is set to StpTri (Step-Tri), LFO is a step-
shape, Tri (Triangle) waveform. The "LFO Freq [Hz]" parameter
sets the original triangle waveform speed. Changing the "Step
Freq [Hz]" parameter enables you to adjust the width of the steps.
When "LFO Waveform" is set to Rndm (Random), the "Step Freq
[Hz]" parameter uses a random LFO cycle.
LFO Frequency
Step Frequency
Step-Tri
BPM
Step Base Note
Times
The width of an LFO step, or a cycle of random LFO, is obtained
by multiplying the length of a note ( ... ) (selected for "Step Base
Note," in relation to the tempo specified in "BPM," or the MIDI
Clock tempo if "BPM" is set to MIDI) by the number specified in
the "Times" parameter.
Wet/Dry
The effect sound's phase will be reversed when you set this
parameter in the range of values from –Wet to –1:99.
226
Sets the balance
–Wet...
between the effect
–99 : 1, Dry,
and the dry input
99 : 1...Wet
p.226
Selects a modulation
Off...Tempo
source for Wet/Dry
Sets the modulation
–100...+100
amount for Wet/Dry
LFO Phase
0 +90 +180 [degree]
–90 0 [degree]
Random Filter LFO
Step Frequency
Random
015: St.MultiModeFltr (Stereo
Multi Mode Filter)
This is a multi-mode filter with four types; low pass, high pass,
band pass, and band reject. You can use LFO or dynamic
modulation to vary the cutoff frequency or resonance.
Stereo In - Stereo Out
Left
Multimode Filter
Trim
LPF
HPF
Filter Type
BPF
BRF
Multimode Filter
Trim
Right
LFO Shape
LFO: Tri / Sine
Paramter Value
LPF, HPF, BPF,
←
Filter Type
BRF
←
Trim 0...100
←
Cutoff 0...100
Src Source Off...Tempo
Amt Amount –100...+100
←
Resonance 0...100
Src Source Off...Tempo
Amt Amount –100...+100
Depth LFO Depth 0...100
LFO Tri (Triangle),
LFO
Waveform Sine
LFO Phase
←
–180...+180
[deg]
LFO Freq
LFO [Hz] 0.02...20.00
[Hz]
Src Source Off...Tempo
–20.00...
Amt Amount
+20.00
BPM/MIDI
MIDI Sync Off, On
Sync
MIDI,
←
BPM 40.00...
300.00
←
Base Note ...
←
Times x1...x32
←
Drive Sw Off, On
←
DriveLevel 0...100
←
Drive Gain 0...100
←
Low Boost 0...100
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Wet / Dry
Driver
Output
Driver
Output
Wet / Dry
LFO Phase
Explanation
Selects the type of
filter
Sets the input level
Sets the cutoff frequency
(center frequency)
Selects the
modulation source of
the cutoff
Sets the modulation
amount of the cutoff
Sets the resonance
amount
Selects the source that
will modulate the
amount of resonance
Sets the amount by
which the resonance
will be modulated
Sets the depth of how
the LFO will modulate
the cutoff frequency
Selects the LFO
Waveform
Sets the LFO phase
difference between the
left and right p.226
Sets the speed of the
LFO p.226
Selects a modulation
source for LFO speed
Sets the modulation
amount of LFO speed
When this is on, the LFO
speed is set by BPM, Base
Note, and Times, instead
of Frequency p.223
MIDI syncs to the system
tempo; 40–300 sets the
tempo manually for this
individual effect p.223
Selects the type of
notes that specify the
LFO speed p.223
Sets the number of
notes that specify the
LFO speed p.223
Switches distortion
on/off within the filter
Sets the output level
Sets the distortion
amount
Sets the amount of
low-range boost
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry