Korg KROSS Parameter Manual page 112

Sequencer mode
Loop End
Specifies the last measure of the loop.
Multi REC
Select this if you want to record two or more tracks
simultaneously. It is linked with the on/off setting in the SEQ>
REC page. (see page 108)
SMP (PAD SAMPLER) On/Off
This specifies whether track 15 is used for the pad sampler or as a
conventional track.
This is linked with the SEQ> PROG page's Pad Sampler Rec &
Play setting.
On (checked): Track 15 is used for the pad sampler. In this case,
the track program that's assigned to track 15 is disabled (does not
sound); instead, the on/off events of the pad sampler are recorded
as note-on/off events of the MIDI channel that's assigned to track
15.
Off (unchecked): Track 15 is used as a conventional track. Turn
this off if there are not enough program tracks.
When you strike pads 1-16, samples will sound regardless of this
setting.
STEP (STEP SEQ On/Off)
This specifies whether track 16 is used for the step sequencer or as
a conventional track.
On (checked): Track 16 is used for the step sequencer. In this
case, a drum program is assigned to track 16.
Off (unchecked): Track 16 is used as a conventional track.
If this is On, a drum program is assigned automatically. Even
if you then turn this Off again, the drum program will still be
assigned. Select the program that you want to use as a
conventional timbre.
It is linked with the on/off setting in the SEQ> PROG page.
Track Info
The following information is shown for each track.
• The category of the program
timbre
SEQ> PROG page Status: when set to INT, BTH
SEQ> MIX page Sound: when set to Play
Note: INT is shown if the User category is selected.
• Mute
SEQ> PROG page Status: INT, BTH
SEQ> MIX page Sound: when set to Mute
• Dummy arpeggiator
SEQ> PROG page Status: Off
SEQ> ASSIGN page ARP Assign: when set to A or B
• Pad sampler
COMBI> PROG page PAD SAMPLER On/Off: when set to On
• Step sequencer
COMBI> PROG page STEP SEQ On/Off: when set to On
• Status
COMBI> PROG page Status: when set to Off, EXT, or EX2
• Solo On
Indicates that the Solo function is on
Track Select
Select the MIDI track that you want to record.
01...16: Select the track that you want to record or edit. Use the
cursor buttons   to make the selection.
When Multi REC is off, this also selects the record-enabled track.
When Multi REC is on, the Play/Rec/Mute buttons (SEQ> REC)
select the record-enabled tracks, regardless of the Track Select
setting.
104
[M001...M999]
[Off, On]
[Off, On]
[Off, On]
etc. that's assigned to the
(see page 138)
[01...16]
If other tracks are set to the same MIDI channel as the
selected track, and their Status is set to INT or BTH, they'll
be controlled by the keyboard as well.
Additionally, other tracks set to the same MIDI channel as the
selected track, and their Status set to EXT, EX2, or BTH, will
transmit MIDI to external devices. For another look at this,
please see the table below.
MIDI Channel Status
OFF
INT
Same as the
EXT
selected MIDI Track
EX2
BTH
Different from the
Any setting
selected MIDI Track
Keyboard
This shows the number of the track that will sound when you play
the keyboard.
Battery/AC Icon
Indicates the power supply and the remaining battery capacity.
(see page 2)
Keyboard Keyboard
plays Internal Transmits MIDI
Sounds Out
No No
Yes No
No Yes
No Yes
Yes Yes
No No
[ , , ]