Single Size Effects - Korg KROSS Parameter Manual

Single size effects

About the names of parameters listed in the effect
parameter tables
Two parameter names are listed in these tables.
The parameter name shown at left is the name that's shown in the
display of the KROSS. The parameter name shown at right is the
full name of the parameter. If a "←" is shown, the name shown in
the display of the KROSS is the full parameter name.
Explanations of the parameter will use the full name.
000: No Effect
Select this option when you do not use any effects. The Insert
Effect section outputs unprocessed signals and the Master Effect
section mutes the output.
001: Stereo Compressor
This effect compresses the input signal to regulate the level and
give a "punchy" effect. It is useful for guitar, piano, and drum
sounds. This is a stereo compressor. You can link left and right
channels, or use each channel separately.
Stereo In - Stereo Out
Left
EQ Trim
LEQ HEQ
Envelope - Control
Envelope Select
Envelope - Control
EQ Trim
LEQ HEQ
Right
Paramter Value
L/R Mix,
Envelope
Env Sel L/R Individ-
Select
ually
Sens Sensitivity 1...100
←
Attack 1...100
←
PreEQ Trim 0...100
Low EQ Low,
Pre LEQ Fc
Frequency Mid-Low
High EQ High,
Pre HEQ Fc
Frequency Mid-High
Low EQ
LEQ [dB] –15.0...+15.0
Gain [dB]
High EQ
HEQ [dB] –15.0...+15.0
Gain [dB]
←
Out Level 0...100
Src Source Off...Tempo
Amt Amount –100...+100
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Wet / Dry
Compressor
Output Level
Output Level
Compressor
Wet / Dry
Explanation
Determines whether
the left and right
channels are linked or
used separately p.217
Sets the sensitivity
p.217
Sets the attack level
p.218
Sets the EQ input
level
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
Sets the gain of the
Low EQ
Sets the gain of the
High EQ
Sets the output level
of the compressor
p.229
Selects the
modulation source
for the compressor
output level
Sets the modulation
amount for the
compressor output
level
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
Single size effects 000: No Effect
Envelope
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
Sensitivity
Output Level
The "Sensitivity" parameter sets the sensitivity of the compressor.
If this parameter is set to a higher value, lower level sounds will be
boosted. With a higher Sensitivity, the overall volume level is
higher. To adjust the final volume level, use the "Output Level"
parameter.
Level
Wet
Dry
Attack
This parameter controls the attack level.
Level
Attack=80
Attack=20
Dry
002: Red Comp
When playing chords on an electric piano or similar instrument,
it's helpful to use a compressor to keep each note smooth and well-
balanced. In addition to a distinctive percussive accent, it will also
provide a long sustain. This effect models a popular compressor
with a clean sound that's perfect for pop and funk music.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Compressor
Envelope - Control
Right
Paramter Value
Sens Sensitivity 1...100
←
Attack 1...100
←
Level 0...100
Dry, 1 : 99...
Wet/Dry Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Compressor - Sensitivity
Sensitivity=100
Sensitivity=40
Time
Compressor - Attack
Wet
Time
Wet / Dry
Output Level
Wet / Dry
Explanation
Sets the sensitivity
Sets the attack level
Sets the output level
of the compressor
Sets the balance
between the effect
and the dry input
Selects the
modulation source
for the compressor
output level
Sets the modulation
amount for the
compressor output
level
217