Stereo Chorus - Korg KROSS Parameter Manual

Effect Guide
←
RotorRatio
MicDistnce Mic Distance 0...100
←
Mic Spread
←
Wet/Dry
Src Source
Amt Amount
Mode
This parameter sets how the modulation source switches between
rotation and stop.
When "Mode" = Toggle, the speaker rotates or stops alternately
each time you press the pedal or move the modulation wheel.
Via MIDI, rotation will switch between start and stop each
time the modulation amount exceeds 64.
When "Mode" = Moment, the speaker rotates by default, and
stops only when you press the pedal or move the modulation
wheel.
Via MIDI, modulation values above 64 make the speaker
rotate, and values below 64 make it stop.
Speed Switch
This parameter controls how the rotation speed (slow and fast) is
switched via the modulation source.
When "SMode" = Toggle, the speed will switch between slow and
fast each time you press the pedal or move the modulation wheel.
Via MIDI, the speed will switch each time the modulation
amount exceeds 64.
When "Mode" = Moment, the speed is usually slow. It becomes
fast only when you press the pedal or move the modulation wheel.
Via MIDI, modulation values above 64 set the speed to Fast,
and values below 64 set it to Slow.
Manual Speed
If you wish to control the rotation speed manually, instead of
switching between Slow and Fast, select a modulation source in
the "Manual Speed" parameter. If you don't want to use manual
control, set this to Off.
Horn Acceleration
Rotor Acceleration
On a real rotary speaker, the rotation speed accelerates or
decelerates gradually after you switch the speed. The "Horn" and
"Rotor Acceleration" parameters set the transition times between
fast and slow speeds.
Mic Distance
Mic Spread
This is a simulation of stereo microphone settings.
Microphone
Mic Distance
Rotary Speaker (Top View)
252
Adjusts the (low-
frequency) rotor
Stop, speed. Standard
0.50...2.00 value is 1.00.
Selecting "Stop" will
stop the rotation
Sets the distance
between the micro-
phone and rotary
speaker p.252
Sets the angle of left
0...100 and right micro-
phones p.252
Dry, Sets the balance
1:99...99:1, between the effect
Wet and the dry input
Selects a modulation
Off...Tempo
source for Wet/Dry
Sets the modulation
–100...+100
amount for Wet/Dry
Rotary Speaker - Mic Placement
Mic Spread
Microphone
Mic Distance
Note:Effects 064–120 can be selected only for the master effect.
The master effect does not output a Dry (direct) sound; only the
Wet (effect) sound is output, and then mixed with the Dry (direct)
sound in the L/R bus.
The parameter names and effect block diagrams are shown in the
same way as for the other effects that can also be used as an insert
effect, but please note the following points.
• "Wet/Dry" parameter: This controls the level of the Wet (effect)
sound. The Dry (direct) sound is not output.
• The output for the Dry (direct) sound is not shown in the effect
block diagram.
("In/Out" on page 210)

064: Stereo Chorus

This effect adds thickness and warmth to the sound by modulating
the delay time of the input signal. You can add spread to the sound
by offsetting the phase of the left and right LFOs from each other.
Stereo In - Stereo Out
Left
LEQ HEQ
EQ Trim
LEQ HEQ
EQ Trim
Right
LFO: Tri / Sine
Paramter Value
LFO Tri (Triangle),
LFO
Waveform Sine
LFO Phase
←
–180...+180
[deg]
LFO Freq
LFO [Hz] 0.02...20.00
[Hz]
Src Source Off...Tempo
–20.00...
Amt Amount
+20.00
BPM/MIDI
MIDI Sync Off, On
Sync
MIDI,
←
BPM 40.00...
300.00
←
Base Note ...
←
Times x1...x32
←
Depth 0...100
L Pre Delay
L Dly[ms] 0.0...50.0
[ms]
R Pre Delay
R Dly[ms] 0.0...50.0
[ms]
PreEQ Trim Pre EQ Trim 0...100
Low EQ Low,
Pre LEQ Fc
Frequency Mid-Low
High EQ High,
Pre HEQ Fc
Frequency Mid-Hi
Low EQ Gain
LEQ [dB] –15.0...+15.0
[dB]
Wet / Dry
Chorus
Chorus
Wet / Dry
LFO Phase
Explanation
Selects the LFO
Waveform
Sets the LFO phase
difference between
the left and right
p.226
Sets the speed of the
l
LFO p.226
Selects a modulation
source for LFO speed
Sets the modulation
amount of LFO speed
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency
p.223
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Selects the type of
notes that specify the
LFO speed p.223
Sets the number of
notes that specify the
LFO speed p.223
Sets the depth of LFO
modulation
Sets the delay time
for the left channel
p.253
Sets the delay time
for the right channel
p.253
Sets the EQ input
level
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
Sets the gain of the
Low EQ