Controlling Effects - Korg KROSS Parameter Manual

Appendices
• When you set the Pan (SEQ> MIX) in Sequencer mode, or
when you re-select the song or return to the beginning of the
measure in Sequencer mode, Panpot messages (except for
RND) will be transmitted by each track where the Status is
BTH, EXT, or EX2. See "Pan" on page 106, GLOBAL G–
MIDI> OUT "Track MIDI Out" on page 162.
Post insert effect pan (CC#08) [Bn, 08, vv]
(vv: value, where 00 is far left, 64 is center, and 127 is far right)
When the above CC# is assigned to the Assignable Pedal, using
that pedal will transmit Post Insert Effect Panpot messages, and
the panning of the sound following the insert effect will change.
When this message is received, the result will be the same as when
the controller is used.
• In Program mode, this message is transmitted/received on the
global MIDI channel. In Combination, and Sequencer modes,
this message is transmitted/received on the MIDI channel
specified for each insert effect.
• When you set Pan: #8 (S–FX ROUTING> MIXER) in
Sequencer mode, or when you re-select the song or return to the
beginning of the measure in Sequencer mode, Post Insert Effect
Panpot messages will be transmitted by each track whose
Status is BTH, EXT, or EX2. For more information, please see
the "10–3: IFX (Insert FX Setup)" section on page 133.

Controlling effects

Effect control 1 (CC#12) [Bn, 0C, vv]
Effect control 2 (CC#13) [Bn, 0D, vv]
When the above CC# is assigned to the Assignable Pedal, using
that pedal will transmit Effect Control 1/2 messages, and the
specified dynamic modulation will be controlled. When this
message is received, the result will be the same as when the
controller is used.
Although various types of control change can be selected as
dynamic modulation sources, Effect Control 1 (CC#12) and 2
(CC#13) are dedicated for dynamic modulation.
Effect 1 depth (Send 2) (CC#91) [Bn, 5B, vv]
Effect 3 depth (Send 1) (CC#93) [Bn, 5D, vv]
When the above CC# is assigned to the Assignable Pedal, using
that pedal will transmit Effect 1 Depth (Send 2) or Effect 3 Depth
(Send 1) messages, and the send level 1 or 2 to the master effects
MFX1 or MFX2 will be controlled respectively. When this
message is received, the result will be the same as when the
controller is used.
On the corresponding MIDI channels, this will simultaneously
control the timbre/track setting as well as the setting following the
Insert Effect.
• In Combination, and Sequencer modes, the actual send level of
the timbre/track is determined by multiplying this value with
the send 1/2 settings for each oscillator (P–FX ROUTING>
SEND). (See "Send 1 (MFX1)," "Send 2 (MFX2)" on page 91,
GLOBAL G–MIDI> OUT "Track MIDI Out" on page 162)
• When you adjust Send 1 (MFX1) or Send 2 (MFX2) (S–FX
ROUTING> SEND) in Sequencer mode, or when you re-select
a song or return to the beginning of the measure in Sequencer
mode, Send 1/2 will be transmitted by each track where the
Status is BTH, EXT, or EX2. (see "Send1 (MFX1)" on
page 132).
Effect 2 depth (IFX1–5 on/off) (CC#92) [Bn, 5C, vv]
Effect 4 depth (MFX1, 2 on/off) (CC#94) [Bn, 5E, vv]
Separately from the effect on/off settings in each mode, Effect
Global SW (GLOBAL> SYSTEM) allows you to turn off insert
effects IFX1–5 and master effects MFX1, 2. For master effects
MFX1 and 2, you can also use the REALTIME CONTROLS
section EFFECT row's MASTER FX to turn them off.
If you uncheck Enable IFX1–5, or Enable MFX1&2, the
corresponding message will be transmitted with vv=0 [00]. If you
check these settings, the corresponding message will be
316
transmitted with vv=127 [7F]. If you uncheck these settings, the
corresponding effect(s) will be turned off as a group. If you check
these settings, the on/off settings of each mode will be used. The
same applies to reception. (vv of 00 is off, and 01 or greater is the
original setting.) These messages are transmitted/received on the
global MIDI channel. ("IFX 1–5 on/off" - "MFX 1, 2 on/off" on
page 60, page 62)
Note: These messages are defined simply for use in adjusting the
effect levels, and may not have the same function on another
instrument connected to the KROSS.
Using various controllers
Here we will explain typical ways to use the various controllers.
Foot controller (CC#04) [Bn, 04, vv]
If the above CC# is assigned as the Assignable Pedal function, this
message will be transmitted when the controller is used.
• In Combination and Sequencer modes, transmission/reception
of this message can be turned on/off independently for each
timbre/track (Enable Foot Pedal/Switch C/S–MIDI
FILTER>3).
Damper pedal (CC#64) [Bn, 40, vv]
This message is transmitted when you use a damper pedal
(optional DS-1H) connected to the DAMPER jack, and the damper
effect will be turned on/off. If the DS-1H is used, a half-damper
effect can be applied.
In Combination and Sequencer modes, transmission/reception of
this message can be turned on/off independently for each timbre/
track (Enable Damper C/S–MIDI FILTER>3).
SW1 modulation (CC#80) [Bn, 50, vv]
SW2 modulation (CC#81) [Bn, 51, vv]
If the above CC# are assigned as the function of SW1 or SW2,
using the switch will transmit this message with vv=127 [7F] for
ON, and vv=00 [00] for OFF.
• In Combination and Sequencer modes, transmission/reception
of these messages can be turned on/off independently for each
timbre/track (Enable SW1, Enable SW2 C/S–MIDI
FILTER>3)
Foot switch (CC#82) [Bn, 52, vv]
If the above CC# is assigned as the function of the ASSIGNABLE
SWITCH, using the switch will transmit this message with vv=127
[7F] for ON, and vv=00 [00] for OFF.
• In Combination and Sequencer modes, transmission/reception
of this message can be turned on/off independently for each
timbre/track ("Enable Foot Switch" C/S–MIDI FILTER>3.
Sostenuto (CC#66) [Bn, 42, vv]
If the above CC# is assigned as the function of the ASSIGNABLE
SWITCH, using the switch will transmit this message with vv=127
[7F] for ON, and vv=00 [00] for OFF, and the sostenuto effect will
be turned on/off. When this message is received, the result will be
the same as when the controller is used (OFF for vv=63 [3F] or
below, and ON for vv=64 [40] or above).
Soft pedal (CC#67) [Bn, 43, vv]
If the above CC# is assigned as the function of the ASSIGNABLE
SWITCH, using the switch will transmit, and the soft pedal effect
will be turned on. When this message is received, the result will be
the same as when the controller is used.
When "Foot controller (CC#04)"–"Soft pedal (CC#67)" are used
on the KROSS, the specified alternate modulation or dynamic
modulation etc. will be controlled. When these messages are
received, the result will be the same as if the controller had been
used. For "SW1 modulation (CC#80)"–"Soft pedal (CC#67)," vv
of 63 [3F] or less will be OFF, and 64 [3F] or greater will be ON.
Controlling via the controllers of a connected