Comp - Mt.delay (Compressor - Multitap Delay) - Korg KROSS Parameter Manual

115: Comp - Mt.Delay (Compressor -
Multitap Delay)
This effect combines a mono compressor and a multitap delay.
You can change the order of the effects.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Compressor
EQ Trim LEQ HEQ
+ Comp
Output Level
Right
Envelope - Control
Paramter Value
Compressor
C Sens Sensitivity 1...100
C Attack Attack 1...100
Level Out Level 0...100
C EQ Trim Pre EQ Trim 0...100
Low EQ Gain
C LEQ –15...+15
[dB]
High EQ
C HEQ –15...+15
Gain [dB]
Multitap Delay
Tap1
DT1[ms] 0.0...548.0
Time [ms]
←
Tap1 Level 0...100
Tap2
D T2[ms] 0.0...548.0
Time [ms]
Feedback
Fback(T2) –100...+100
(Tap2)
High Damp
HiDamp [%] 0...100
[%]
Dry,
D W/D [Dly]Wet/Dry 1 : 99...99 : 1,
Wet
Src [Dly]Source Off...Tempo
Amt [Dly]Amount –100...+100
Comp
→Delay,
←
Routing
Delay →
Comp
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Wet / Dry
Routing
Multitap Delay
Feedback
Delay
(2)
(1)
High Damp
Mt.Dly Wet / Dry
Wet / Dry
Explanation
Sets the sensitivity
p.217
Sets the attack level
p.217
Sets the compressor
output level p.217
Sets the EQ input
level
Sets the gain of Low
EQ
Sets the gain of High
EQ
Sets the Tap1 delay
time
Sets the Tap1 output
level p.267
Sets the Tap2 delay
time
Sets the Tap2
feedback amount
Sets the damping
amount in the high
range p.266
Sets the multitap
delay effect balance
Selects the Wet/Dry
modulation source
for the multitap delay
Sets the Wet/Dry
modulation amount
for the multitap delay
Switches the order of
the compressor and
multitap delay
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
Single size effects 113: Early Reflections
116: Limiter - Mt.Delay (Limiter -
Multitap Delay)
This effect combines a mono limiter and a multitap delay. You can
change the order of the effects.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Limiter
+ Limiter
Gain Adjust
Right
Envelope - Control
Paramter Value
Limiter
1.0 : 1...
L Ratio Ratio
50.0 : 1, Inf : 1
Threshold
Thrsh [dB] –40...0
[dB]
L Attack Attack 1...100
←
Release 1...100
Gain Adjust –Inf,
L Gain [dB]
[dB] –38...+24
Multitap Delay
Tap1
D T1[ms] 0.0...1360.0
Time [ms]
←
Tap1 Level 0...100
D T2 [ms] Tap2 Time 0.0...1360.0
Feedback
F.back(T2) –100...+100
(Tap2)
High Damp
HiDamp [%] 0...100
[%]
Dry, 1 : 99...
D W/D [Dly]Wet/Dry
99 : 1, Wet
Src [Dly]Source Off...Tempo
Amt [Dly]Amount –100...+100
Limiter →
←
Routing Delay, Delay
→ Limiter
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Routing Wet / Dry
Multitap Delay
Feedback
Delay
(2)
(1)
High Damp
Mt.Dly Wet / Dry
Wet / Dry
Explanation
Sets the signal
compression ratio
p.218
Sets the level above
which the
compressor is applied
p.218
Sets the attack time
Sets the release time
Sets the limiter
output gain p.218
Sets the Tap1 delay
time
Sets the Tap1 output
level p.267
Sets the Tap2 delay
time
Sets the Tap2
feedback amount
Sets the damping
amount in the high
range p.266
Sets the multitap
delay effect balance
Selects the multitap
delay's Wet/Dry
modulation source
Sets the multitap
delay's Wet/Dry
modulation amount
Switches the order of
the limiter and
multitap delay
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
279